Nissan Pathfinder (2006 year). Manual — part 268
POWER WINDOW SYSTEM
GW-25
C
D
E
F
G
H
J
K
L
M
A
B
GW
2006 Pathfinder
WIWA1039E
GW-26
POWER WINDOW SYSTEM
2006 Pathfinder
Terminal and Reference Value for Main Power Window and Door Lock/Unlock
Switch
EIS007RG
Terminal
Wire Color
Item
Condition
Voltage (V)
(Approx.)
1
R
Rear power window LH
UP signal
When rear LH switch in
main power window and door
lock/unlock switch is operated
UP
Battery voltage
2
BR
Limit switch and encoder ground
—
0
3
LG
Rear power window LH
DOWN signal
When rear LH switch in
main power window and door
lock/unlock switch is operated
DOWN
Battery voltage
5
P
Rear power window RH
DOWN signal
When rear RH switch in
main power window and door
lock/unlock switch is operated
DOWN
Battery voltage
7
Y
Rear power window RH
UP signal
When rear RH switch in
main power window and door
lock/unlock switch is operated
UP
Battery voltage
8
L/W
Front power window motor RH UP
signal
When power window motor is
operated UP
Battery voltage
9
Y
Limit switch signal
Front power window LH is
between fully-open and just
before fully-closed position (ON)
0
Front power window LH is
between just before fully-closed
position and fully-closed position
(OFF)
5
10
W/R
RAP signal
When ignition switch ON
Battery voltage
Within 45 seconds after ignition
switch is turned to OFF
Battery voltage
More than 45 seconds after igni-
tion switch is turned to OFF
0
When front door LH or RH open
or power window timer operates
0
11
G/Y
Front power window motor RH
DOWN signal
When power window motor is
operated DOWN
Battery voltage
12
GR
Front power window motor LH
DOWN signal
When power window motor is
operated DOWN
Battery voltage
13
LB
Encoder pulse signal
When power window motor oper-
ates
15
W/R
Encoder power supply
When ignition switch ON or
power window timer operates
10
16
O
Front power window motor LH UP
signal
When power window motor is
operated UP
Battery voltage
17
B
Ground
—
0
19
L
Battery power supply
—
Battery voltage
OCC3383D
POWER WINDOW SYSTEM
GW-27
C
D
E
F
G
H
J
K
L
M
A
B
GW
2006 Pathfinder
Terminal and Reference Value for BCM
EIS007RH
Refer to
BCS-12, "Terminals and Reference Values for BCM"
Work Flow
EIS007RI
1.
Check the symptom and customer's requests.
2.
Understand the outline of system. Refer to
.
3.
According to the trouble diagnosis chart, repair or replace the cause of the malfunction.
Refer to
GW-29, "Trouble Diagnoses Symptom Chart"
4.
Does power window system operate normally? Yes, GO TO 5, If No, GO TO 3.
5.
Inspection end.
CONSULT-II Function (BCM)
EIS007RJ
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II INSPECTION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1.
Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
2.
Turn ignition switch ON.
3.
Touch “START (NISSAN BASED VHCL)”.
BCM diagnostic
test item
Diagnostic mode
Content
Inspection by part
WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR
Displays BCM input/output data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS
Displays BCM self-diagnosis results.
CAN DIAG SUPPORT
MNTR
The results of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER
BCM part number can be read.
CONFIGURATION
Performs BCM configuration read/write functions.
BBIA0538E
BCIA0029E
GW-28
POWER WINDOW SYSTEM
2006 Pathfinder
4.
Touch “BCM”.
If “BCM” is not indicated, refer to
5.
Touch “RETAINED PWR”.
6.
Select diagnosis mode.
“ACTIVE TEST”, “WORK SUPPORT” and "DATA MONITOR"
are available.
ACTIVE TEST
WORK SUPPORT
DATA MONITOR
BCIA0030E
LIIA0163E
BCIA0031E
Test Item
Description
RETAINED PWR
This test is able to supply RAP signal (power) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-II screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-II can be operated with ignition switch in OFF position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-II screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-II might be stuck if
“RETAINED PWR” is turned “ON” or “OFF” on CONSULT-II screen when ignition switch is OFF.
Work item
Description
RETAINED PWR
RAP signal’s power supply period can be changed by mode setting. Selects RAP signal’s power
supply period between three steps
●
MODE1 (45 sec.)/MODE2 (OFF)/MODE 3 (2 min.).
Work item
Description
IGN ON SW
Indicates (ON/OFF) condition of ignition switch
POWER WINDOW SYSTEM
GW-29
C
D
E
F
G
H
J
K
L
M
A
B
GW
2006 Pathfinder
Trouble Diagnoses Symptom Chart
EIS007RK
●
Check that other systems using the signal of the following systems operate normally.
BCM Power Supply and Ground Circuit Check
EIS007RL
Refer to
BCS-16, "BCM Power Supply and Ground Circuit Check"
DOOR SW–DR
Indicates (ON/OFF) condition of front door switch driver side
DOOR SW–AS
Indicates (ON/OFF) condition of front door switch passenger side
Symptom
Repair order
Refer to page
None of the power windows can be operated using any switch
1. BCM power supply and ground circuit check
2. Main power window and door lock/unlock
power supply and ground circuit check
3. Replace main power window and door lock/
unlock switch
Front power window LH alone does not operate
1. Front power window motor LH circuit check
2. Replace main power window and door lock/
unlock switch
Front power window RH alone does not operate from power win-
dow and door lock/unlock switch RH
1. Front power window RH circuit check (power
window and door lock/unlock switch operation)
Front power window RH alone does not operate from main power
window and door lock/unlock switch
1. Main power window and door lock/unlock
power supply and ground circuit check
2. Front power window RH circuit check (main
power window and door lock/unlock switch
operation)
Anti-pinch system does not operate normally (Front LH)
1. Door window sliding part malfunction
●
A foreign material adheres to window glass
or glass run rubber.
●
Glass run rubber wear or deformation.
●
Sash is tilted too much, or not enough.
—
2. Limit switch adjusting
3. Limit switch circuit check front LH
4. Encoder circuit check front LH
Rear power window LH alone does not operate from rear power
window switch LH
1. Rear power window LH circuit check (rear
power window switch LH operation)
Rear power window LH alone does not operate from main power
window and door lock/unlock switch
1. Rear power window LH circuit check (main
power window and door lock/unlock switch
operation)
Rear power window RH alone does not operate from rear power
window switch RH
1. Rear power window RH circuit check (rear
window switch RH operation)
Rear power window RH alone does not operate from main power
window and door lock/unlock switch
1. Rear power window RH circuit check (main
power window and door lock/unlock switch
operation)
Power window retained power operation does not operate properly
1. Check the retained power operation mode
setting.
2. Door switch check
3. Replace BCM.
GW-30
POWER WINDOW SYSTEM
2006 Pathfinder
Main Power Window and Door Lock/Unlock Switch Power Supply and Ground
Circuit Check
EIS007RM
1.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between main power window and door lock/
unlock switch connector D7 terminal 10, D8 terminal 19 and
ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 3.
2.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect main power window and door lock/unlock switch.
3.
Check continuity between main power window and door lock/
unlock switch connector D8 terminal 17 and ground.
OK or NG
OK
>> Power supply and ground circuit are OK.
NG
>> Repair or replace harness.
3.
CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM and main power window and door lock/unlock
switch.
3.
Check continuity between BCM connector and main power win-
dow and door lock/unlock switch connectors.
4.
Check continuity between BCM and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
10 - Ground
: Battery voltage
19 - Ground
: Battery voltage
LIIA2297E
17 - Ground
: Continuity should exist.
LIIA1253E
Connector
Terminal
Connector
Terminal
Continuity
A
B
BCM: M20
68
Main power window and
door lock/unlock switch:
D7
10
Yes
C
19
69
Main power window and
door lock/unlock switch:
D8
Yes
Connector
Terminal
Ground
Continuity
A
BCM: M20
68
No
69
No
LIIA2215E
POWER WINDOW SYSTEM
GW-31
C
D
E
F
G
H
J
K
L
M
A
B
GW
2006 Pathfinder
4.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM.
2.
Turn ignition switch ON.
3.
Check voltage between BCM connector M20 terminals 68, 69
and ground.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Replace BCM. Refer to
BCS-27, "Removal and Installa-
Front Power Window Motor LH Circuit Check
EIS007RO
1.
CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between main power window and door lock/
unlock switch connector D7 terminals 12, 16 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Replace main power window and door lock/unlock switch. Refer to
2.
CHECK POWER WINDOW MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect main power window and door lock/unlock switch and
front power window motor LH.
3.
Check continuity between main power window and door lock/
unlock switch connector and front power window motor LH con-
nector.
4.
Check continuity between main power window and door lock/unlock switch connector and ground.
OK or NG
OK
>> Replace front power window motor LH. Refer to
GW-58, "Front Door Glass Regulator"
NG
>> Repair or replace harness.
68 - Ground
: Battery voltage
69 - Ground
: Battery voltage
LIIA0917E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
D7
12
Ground
UP
0
DOWN
Battery voltage
16
UP
Battery voltage
DOWN
0
LIIA1996E
Connector
Terminal
Connector
Terminal
Continuity
A
B
Main power window
and door lock/unlock
switch: D7
12
Front power
window motor
LH: D9
1
Yes
16
5
Yes
Connector
Terminal
Ground
Continuity
A
Main power window and
door lock/unlock switch: D7
12
No
16
No
LIIA2216E
GW-32
POWER WINDOW SYSTEM
2006 Pathfinder
Front Power Window RH Circuit Check (Power Window and Door Lock/Unlock
Switch RH Operation)
EIS007RP
1.
CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor RH.
3.
Turn ignition switch ON.
4.
Check voltage between front power window motor RH connector
and ground.
OK or NG
OK
>> Replace front power window motor RH. Refer to
GW-58, "Front Door Glass Regulator"
.
NG
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between power window and door lock/unlock
switch RH connector D105 terminal 8 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM and power window and door lock/unlock switch
RH.
3.
Check continuity between BCM connector and power window
and door lock/unlock switch RH connector.
4.
Check continuity between BCM and ground.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Repair or replace harness.
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
Front power window
motor RH: D104
1
Ground
UP
0
DOWN
Battery voltage
2
UP
Battery voltage
DOWN
0
LIIA2431E
8 - Ground
: Battery voltage
LIIA1976E
Connector
Terminal
Connector
Terminal
Continuity
A
B
BCM: M20
68
Power window and
door lock/unlock
switch RH: D105
8
Yes
Connector
Terminal
Ground
Continuity
A
BCM: M20
68
No
LIIA2166E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст