Nissan Pathfinder (2006 year). Manual — part 382
AUTOMATIC DRIVE POSITIONER
SE-61
C
D
E
F
G
H
J
K
L
M
A
B
SE
2006 Pathfinder
2.
CHECK SLIDING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat
switch LH connector.
2.
Check continuity between driver seat control unit connector P2
terminals 11, 26 and power seat switch LH connector P8 termi-
nals 1, 7.
3.
Check continuity between driver seat control unit connector P2
terminals 11, 26 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK SLIDING SWITCH
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Replace driver seat control unit. Refer to
NG
>> Replace power seat switch LH. Refer to
11 - 7
: Continuity should exist.
26 - 1
: Continuity should exist.
11 - Ground
: Continuity should not exist.
26 - Ground
: Continuity should not exist.
LIIA1125E
Terminal
Condition
Continuity
7
3
Sliding switch ON (BACKWARD operation)
Yes
Other than above
No
1
Sliding switch ON (FORWARD operation)
Yes
Other than above
No
LIIA1126E
SE-62
AUTOMATIC DRIVE POSITIONER
2006 Pathfinder
Reclining Switch Inspection
EIS007VK
1.
CHECK FUNCTION
With CONSULT-II
With “RECLN SW-FR, RECLN SW-RR” on the DATA MONITOR,
operate the reclining switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Reclining switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK RECLINING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and power seat switch LH.
2.
Check continuity between driver seat control unit connector P2
terminals 12, 27 and power seat switch LH connector P8 termi-
nals 9, 10.
3.
Check continuity between driver seat control unit connector P2
terminals 12, 27 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item [OPERATION
or UNIT]
Contents
RECLN SW-FR
“ON/
OFF”
ON/OFF status judged from the reclining switch
(FR) signal is displayed.
RECLIN SW-RR
“ON/
OFF”
ON/OFF status judged from the reclining switch
(RR) signal is displayed.
PIIA0313E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
P2
12
Ground
Reclining switch ON
(BACKWARD oper-
ation)
0
Other than above
Battery voltage
27
Reclining switch ON
(FORWARD opera-
tion)
0
Other than above
Battery voltage
PIIA4580E
12 - 9
: Continuity should exist.
27 - 10
: Continuity should exist.
12 - Ground
: Continuity should not exist.
27 - Ground
: Continuity should not exist.
LIIA1127E
AUTOMATIC DRIVE POSITIONER
SE-63
C
D
E
F
G
H
J
K
L
M
A
B
SE
2006 Pathfinder
3.
RECLINING SWITCH INSPECTION
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Replace driver seat control unit. Refer to
NG
>> Replace power seat switch LH. Refer to
Lifting Switch (Front) Circuit Inspection
EIS007VL
1.
CHECK FUNCTION
With CONSULT-II
With “LIFT FR SW-UP, LIFT FR SW-DN” on the DATA MONITOR,
operate the lifting switch (front) to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Lifting switch (front) circuit is OK.
NG
>> GO TO 2.
Terminal
Condition
Continuity
9
3
Reclining switch ON (BACKWARD operation)
Yes
Other than above
No
10
Reclining switch ON (FORWARD operation)
Yes
Other than above
No
LIIA1128E
Monitor item [OPERATION
or UNIT]
Contents
LIFT FR SW-DN
"ON/
OFF"
ON/OFF status judged from the FR lifter switch
(DOWN) signal is displayed.
LIFT RR SW-UP
"ON/
OFF"
ON/OFF status judged from the RR lifter switch
(UP) signal is displayed.
PIIA0323E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
P2
13
Ground
Lifting switch (front) ON
(DOWN operation)
0
Other than above
Battery voltage
28
Lifting switch (front) ON
(UP operation)
0
Other than above
Battery voltage
PIIA4583E
SE-64
AUTOMATIC DRIVE POSITIONER
2006 Pathfinder
2.
CHECK LIFTING SWITCH (FRONT) CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and power seat switch LH.
2.
Check continuity between driver seat control unit connector P2
terminals 13, 28 and power seat switch LH connector P8 termi-
nals 5, 6.
3.
Check continuity between driver seat control unit connector P2
terminals 13, 28 and ground
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK LIFTING SWITCH (FRONT)
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Replace driver seat control unit. Refer to
NG
>> Replace power seat switch LH. Refer to
.
13 - 5
: Continuity should exist.
28 - 6
: Continuity should exist.
13 - Ground
: Continuity should not exist.
28 - Ground
: Continuity should not exist.
LIIA1129E
Terminals Condition
Continuity
5
3
Lifting switch (front) ON (DOWN operation)
Yes
Other than above
No
6
Lifting switch (front) ON (UP operation)
Yes
Other than above
No
LIIA1130E
AUTOMATIC DRIVE POSITIONER
SE-65
C
D
E
F
G
H
J
K
L
M
A
B
SE
2006 Pathfinder
Lifting Switch (Rear) Circuit Inspection
EIS007VM
1.
CHECK FUNCTION
With CONSULT-II
With “LIFT RR SW-UP, LIFT RR SW-DN” on the DATA MONITOR,
operate the rear lifting switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Rear lifting switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK LIFTING SWITCH (REAR) CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and power seat switch LH.
2.
Check continuity between driver seat control unit connector P2
terminals 14, 29 and power seat switch connector P8 terminals
2, 8.
3.
Check continuity between driver seat control unit connector P2
terminals 14, 29 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item [OPERATION or
UNIT]
Contents
LIFT RR SW-UP
“ON/OFF”
Operation (ON)/open (OFF) status judged from
the RR lifter switch (UP) signal is displayed.
LIFT RR SW-DN
“ON/OFF”
Operation (ON)/open (OFF) status judged from
the RR lifter switch (DOWN) signal is displayed.
PIIA0323E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
P2
14
Ground
Rear lifting switch ON
(DOWN operation)
0
Other than above
Battery voltage
29
Rear lifting switch ON
(UP operation)
0
Other than above
Battery voltage
PIIA4586E
14 - 8
: Continuity should exist.
29 - 2
: Continuity should exist.
14 - Ground
: Continuity should not exist.
29 - Ground
: Continuity should not exist.
LIIA1131E
SE-66
AUTOMATIC DRIVE POSITIONER
2006 Pathfinder
3.
CHECK LIFTING SWITCH (REAR)
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Replace driver seat control unit. Refer to
NG
>> Replace power seat switch LH. Refer to
.
Power Seat Switch Ground Inspection
EIS007VN
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch LH.
3.
Check continuity between power seat switch LH connector P8
terminal 3 and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Repair or replace harness.
Terminals
Condition
Continuity
8
3
Lifting switch (rear) ON (DOWN operation)
Yes
Other than above
No
2
Lifting switch (rear) ON (UP operation)
Yes
Other than above
No
LIIA1132E
3 - Ground
: Continuity should exist.
LIIA1133E
AUTOMATIC DRIVE POSITIONER
SE-67
C
D
E
F
G
H
J
K
L
M
A
B
SE
2006 Pathfinder
Pedal Adjusting Switch Circuit Inspection
EIS007VO
1.
CHECK FUNCTION
With CONSULT-II
With “PEDAL SW-FR, PEDAL SW-RR” on the DATA MONITOR,
operate the pedal adjusting switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Pedal adjusting switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK PEDAL ADJUSTING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and pedal adjusting switch.
2.
Check continuity between driver seat control unit connector P2
terminals 15, 30 and pedal adjusting switch connector M96 ter-
minals 2, 3.
3.
Check continuity between driver seat control unit connector P2
terminals 15, 30 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item [OPERATION or
UNIT]
Contents
PEDAL SW-FR
“ON/OFF”
Operation (ON)/open (OFF) status judged
from the pedal adjusting switch (FR) signal is
displayed.
PEDAL SW-RR
“ON/OFF”
Operation (ON)/open (OFF) status judged
from the pedal adjusting switch (RR) signal is
displayed.
PIIA4590E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
P2
15
Ground
Pedal adjusting switch ON
(BACKWARD operation)
0
Other than above
Battery voltage
30
Pedal adjusting switch ON
(FORWARD operation)
0
Other than above
Battery voltage
PIIA4591E
15 - 2
: Continuity should exist.
30 - 3
: Continuity should exist.
15 - Ground
: Continuity should not exist.
30 - Ground
: Continuity should not exist.
LIIA0726E
SE-68
AUTOMATIC DRIVE POSITIONER
2006 Pathfinder
3.
CHECK PEDAL ADJUSTING SWITCH
Check continuity between pedal adjusting switch as follows.
OK or NG
OK
>> GO TO 4.
NG
>> Replace pedal adjusting switch.
4.
CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector M96 ter-
minal 1 and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace or replace harness.
Terminals
Condition
Continuity
2
1
Pedal adjusting switch ON (BACKWARD operation)
Yes
Other than above
No
3
Pedal adjusting switch ON (FORWARD operation)
Yes
Other than above
No
LIIA1014E
1 - Ground
: Continuity should exist.
LIIA1015E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст