Nissan Murano Z51 (2008 year). Manual — part 366
SRC-272
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1146 CURTAIN MODULE RH
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000003367703
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
1.
Replace RH side curtain air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2008 October
2009 Murano
B1147 CURTAIN MODULE RH
SRC-273
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1147 CURTAIN MODULE RH
Description
INFOID:0000000003367704
DTC B1147 [GND-SHORT] CURTAIN MODULE RH
For RH side curtain air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite
sensor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of collision whose acceleration exceeds the specified level, the ignition materials are ignited by electric
ignition system. The system burns and introduces the chemical reaction of gas generating materials to gener-
ate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
RH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
RH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic
INFOID:0000000003367705
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-274, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1147
CURTAIN MODULE RH
[GND-SHORT]
RH side curtain air bag module circuit is
shorted to ground
• Disconnection of wiring harness and
short
• Internal breakdown in RH side cur-
tain air bag module
• Replace air bag diagnosis sensor
unit
Revision: 2008 October
2009 Murano
SRC-274
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1147 CURTAIN MODULE RH
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000003367706
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
1.
Replace RH side curtain air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2008 October
2009 Murano
B1148 CURTAIN MODULE RH
SRC-275
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1148 CURTAIN MODULE RH
Description
INFOID:0000000003367707
DTC B1148 [SHORT] CURTAIN MODULE RH
For RH side curtain air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite
sensor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of collision whose acceleration exceeds the specified level, the ignition materials are ignited by electric
ignition system. The system burns and introduces the chemical reaction of gas generating materials to gener-
ate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
RH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
RH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic
INFOID:0000000003367708
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-276, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1148
CURTAIN MODULE RH
[SHORT]
RH side curtain air bag module circuit
are shorted to each other
• Disconnection of wiring harness and
short
• Internal breakdown in RH side cur-
tain air bag module
• Internal breakdown in air bag diag-
nosis sensor unit
Revision: 2008 October
2009 Murano
SRC-276
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1148 CURTAIN MODULE RH
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000003367709
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
1.
Replace RH side curtain air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2008 October
2009 Murano
B1150 CURTAIN MODULE LH
SRC-277
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1150 CURTAIN MODULE LH
Description
INFOID:0000000003367710
DTC B1150 [OPEN] CURTAIN MODULE LH
For LH side curtain air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of collision whose acceleration exceeds the specified level, the ignition materials are ignited by electric
ignition system. The system burns and introduces the chemical reaction of gas generating materials to gener-
ate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic
INFOID:0000000003367711
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-278, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1150
CURTAIN MODULE LH
[OPEN]
LH side curtain air bag module circuit is
open
• Disconnection of wiring harness and
open
• Internal breakdown in LH side cur-
tain air bag module
• Internal breakdown in air bag diag-
nosis sensor unit
Revision: 2008 October
2009 Murano
SRC-278
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1150 CURTAIN MODULE LH
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000003367712
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
1.
Replace LH side curtain air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2008 October
2009 Murano
B1151 CURTAIN MODULE LH
SRC-279
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1151 CURTAIN MODULE LH
Description
INFOID:0000000003367713
DTC B1151 [VB-SHORT] CURTAIN MODULE LH
For LH side curtain air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of collision whose acceleration exceeds the specified level, the ignition materials are ignited by electric
ignition system. The system burns and introduces the chemical reaction of gas generating materials to gener-
ate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic
INFOID:0000000003367714
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-280, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1151
CURTAIN MODULE LH
[VB-SHORT]
LH side curtain air bag module circuit is
shorted to some power supply circuit
• Disconnection of wiring harness and
short
• Internal breakdown in LH side cur-
tain air bag module
• Internal breakdown in air bag diag-
nosis sensor unit
Revision: 2008 October
2009 Murano
SRC-280
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1151 CURTAIN MODULE LH
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000003367715
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
1.
Replace LH side curtain air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2008 October
2009 Murano
B1152 CURTAIN MODULE LH
SRC-281
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1152 CURTAIN MODULE LH
Description
INFOID:0000000003367716
DTC B1152 [GND-SHORT] CURTAIN MODULE LH
For LH side curtain air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of collision whose acceleration exceeds the specified level, the ignition materials are ignited by electric
ignition system. The system burns and introduces the chemical reaction of gas generating materials to gener-
ate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic
INFOID:0000000003367717
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“”SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-282, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1152
CURTAIN MODULE LH
[GND-SHORT]
LH side curtain air bag module circuit is
shorted to ground
• Disconnection of wiring harness and
short
• Internal breakdown in LH side cur-
tain airbag module
• Internal breakdown in air bag diag-
nosis sensor unit
Revision: 2008 October
2009 Murano
SRC-282
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1152 CURTAIN MODULE LH
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000003367718
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
1.
Replace LH side curtain air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2008 October
2009 Murano
B1153 CURTAIN MODULE LH
SRC-283
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1153 CURTAIN MODULE LH
Description
INFOID:0000000003367719
DTC B1153 [SHORT] CURTAIN MODULE LH
For LH side curtain air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In case of collision whose acceleration exceeds the specified level, the ignition materials are ignited by electric
ignition system. The system burns and introduces the chemical reaction of gas generating materials to gener-
ate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic
INFOID:0000000003367720
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-284, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1153
CURTAIN MODULE LH
[SHORT]
LH side curtain air bag module circuit
are shorted to each other
• Disconnection of wiring harness and
short
• Internal breakdown in LH side cur-
tain air bag module
• Internal breakdown in air bag diag-
nosis sensor unit
Revision: 2008 October
2009 Murano
SRC-284
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1153 CURTAIN MODULE LH
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000003367721
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
1.
Replace LH side curtain air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2008 October
2009 Murano
B1154, B1155, B1156, B1157 DIAGNOSIS SENSOR UNIT
SRC-285
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1154, B1155, B1156, B1157 DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000004185622
Checks the entire SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
on the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.
OPERATION
It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally.
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
INSTALLATION
Air bag diagnosis sensor unit is installed under the center console with fixed bolts.
DTC Logic
INFOID:0000000004185623
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-177, "Diagnosis Description"
NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-285, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004185624
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1154
B1155
B1156
B1157
CONTROL UNIT
Air bag diagnosis sensor unit is mal-
functioning or out of the specification
• Malfunction in air bag diagnosis sen-
sor unit
• Configuration in air bag diagnosis
sensor unit does not match the vehi-
cles specification
Revision: 2008 October
2009 Murano
SRC-286
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
B1154, B1155, B1156, B1157 DIAGNOSIS SENSOR UNIT
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2008 October
2009 Murano
B1170, B1171, B1172, B1173 DIAGNOSIS SENSOR UNIT
SRC-287
< COMPONENT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1170, B1171, B1172, B1173 DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000004185625
Checks the entire SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
on the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.
OPERATION
It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally.
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
INSTALLATION
Air bag diagnosis sensor unit is installed under the center console with fixed bolts.
DTC Logic
INFOID:0000000004185626
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-177, "Diagnosis Description"
NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-287, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000004185627
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1170
B1171
B1172
B1173
CONTROL UNIT
Air bag diagnosis sensor unit is mal-
functioning or out of the specification
• Malfunction in air bag diagnosis sen-
sor unit
• Configuration in air bag diagnosis
sensor unit does not match the vehi-
cles specification
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст