Nissan Murano Z51 (2008 year). Manual — part 5
LIFTING SWITCH (REAR)
ADP-61
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-204, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK LIFTING SWITCH (REAR)
ADP-61, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power seat switch. Refer to
ADP-207, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003312403
1.
CHECK LIFTING SWITCH (REAR)
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch (lifting switch rear) connector.
3.
Check continuity between power seat switch (lifting switch rear) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power seat switch. Refer to
ADP-207, "Removal and Installation"
.
Driver seat control unit
Ground
Continuity
Connector
Terminal
B452
15
Not existed
16
Power seat switch (lifting switch rear)
Condition
Continuity
Terminal
35
15
Lifting switch rear (up)
Operate
Existed
Release
Not existed
16
Lifting switch rear (down)
Operate
Existed
Release
Not existed
Revision: 2008 October
2009 Murano
ADP-62
< COMPONENT DIAGNOSIS >
TILT SWITCH
TILT SWITCH
Description
INFOID:0000000003312404
Tilt switch is equipped to the steering column. The operation signal is inputted to the automatic drive positioner
control unit when the tilt switch is operated.
Component Function Check
INFOID:0000000003312405
1.
CHECK FUNCTION
1.
Select “TILT SW-UP”, “TILT SW-DOWN” in “Data monitor” mode with CONSULT-III.
2.
Check tilt switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003312406
1.
CHECK TILT SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between tilt & telescopic switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TILT SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
Status
TILT SW-UP
Tilt switch (up)
Operate
ON
Release
OFF
TILT SW-DOWN
Tilt switch (down)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Tilt & telescopic switch
Connector
Terminals
M102
2
Ground
Battery voltage
3
Automatic drive positioner control unit
Tilt & telescopic switch
Continuity
Connector
Terminal
Connector
Terminal
M75
1
M102
2
Existed
13
3
Revision: 2008 October
2009 Murano
TILT SWITCH
ADP-63
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-205, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK TILT SWITCH
ADP-63, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace tilt & telescopic switch. Refer to
ADP-208, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003312407
1.
CHECK TILT SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic switch connector.
3.
Check continuity between tilt & telescopic switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace tilt & telescopic switch. Refer to
ADP-208, "Removal and Installation"
.
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
1
Not existed
13
Tilt switch
Condition
Continuity
Terminal
1
2
Tilt switch (upward)
Operate
Existed
Release
Not existed
3
Tilt switch (downward)
Operate
Existed
Release
Not existed
Revision: 2008 October
2009 Murano
ADP-64
< COMPONENT DIAGNOSIS >
TELESCOPIC SWITCH
TELESCOPIC SWITCH
Description
INFOID:0000000003312408
Telescopic switch is equipped to the steering column. The operation signal is inputted to the automatic drive
positioner control unit when the telescopic switch is operated.
Component Function Check
INFOID:0000000003312409
1.
CHECK FUNCTION
1.
Select “TELESCO SW-FR”, “TELESCO SW-RR” in “Data monitor” mode with CONSULT-III.
2.
Check telescopic switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003312410
1.
CHECK TELESCOPIC SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between tilt & telescopic switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TELESCOPIC SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
Status
TELESCO SW-FR
Telescopic switch (forward)
Operate
ON
Release
OFF
TELESCO SW-RR
Telescopic switch (backward)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Tilt & telescopic switch
Connector
Terminals
M102
5
Ground
Battery voltage
4
Automatic drive positioner control unit
Tilt & telescopic switch
Continuity
Connector
Terminal
Connector
Terminal
M75
7
M102
5
Existed
19
4
Revision: 2008 October
2009 Murano
TELESCOPIC SWITCH
ADP-65
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-205, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK TELESCOPIC SWITCH
ADP-65, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace tilt & telescopic switch. Refer to
ADP-208, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003312411
1.
CHECK TELESCOPIC SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic switch connector.
3.
Check continuity between tilt & telescopic switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace tilt & telescopic switch. Refer to
ADP-208, "Removal and Installation"
.
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
7
Not existed
19
Telescopic switch
Condition
Continuity
Terminal
1
5
Telescopic switch (for-
ward)
Operate
Existed
Release
Not existed
4
Telescopic switch (back-
ward)
Operate
Existed
Release
Not existed
Revision: 2008 October
2009 Murano
ADP-66
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
SEAT MEMORY SWITCH
Description
INFOID:0000000003312412
Memory switch and set switch is equipped on the seat memory switch installed to the driver side door trim.
The operation signal is inputted to the driver seat control unit when the memory switch and set switch is oper-
ated.
Component Function Check
INFOID:0000000003312413
1.
CHECK FUNCTION
1.
Select “MEMORY SW 1”, “MEMORY SW 2”, “SET SW” in “Data monitor” mode with CONSULT-III.
2.
Check seat memory switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000003312414
1.
CHECK SEAT MEMORY SWITCH SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Turn ignition switch ON.
4.
Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK MEMORY SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect seat memory switch connector.
3.
Check continuity between driver seat control unit harness connector and seat memory switch harness
connector.
Monitor item
Condition
Status
MEMORY SW 1
Memory switch 1
Push
ON
Release
OFF
MEMORY SW 2
Memory switch 2
Push
ON
Release
OFF
SET SW
Set switch
Push
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Terminals
B452
27
Ground
5
28
29
Revision: 2008 October
2009 Murano
SEAT MEMORY SWITCH
ADP-67
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-204, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK MEMORY SWITCH GROUND CIRCUIT
Check continuity between seat memory switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK SEAT MEMORY SWITCH
ADP-67, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace seat memory switch. Refer to
ADP-206, "Removal and Installation"
.
5.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003312415
1.
CHECK SEAT MEMORY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect seat memory switch connector.
3.
Check continuity between seat memory switch terminals.
Driver seat control unit
Seat memory switch
Continuity
Connector
Terminal
Connector
Terminal
B452
27
D13
1
Existed
28
2
29
3
Driver seat control unit
Ground
Continuity
Connector
Terminal
B452
27
Not existed
28
29
Seat memory switch
Ground
Continuity
Connector
Terminal
D13
4
Existed
Revision: 2008 October
2009 Murano
ADP-68
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace seat memory switch. Refer to
ADP-206, "Removal and Installation"
.
Seat memory switch
Condition
Continuity
Terminal
4
1
Memory switch 1
Push
Existed
Release
Not existed
2
Memory switch 2
Push
Existed
Release
Not existed
3
Set switch
Push
Existed
Release
Not existed
Revision: 2008 October
2009 Murano
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-69
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000003600949
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000003600950
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Is the inspection result normal?
YES
>> Changeover switch function is OK.
NO
>> Refer to
ADP-69, "CHANGEOVER SWITCH : Diagnosis Procedure"
.
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000003600951
1.
CHECK CHANGEOVER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK CHANGEOVER SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
MIR CHNG SW-R/L
When operating the changeover toward the right or left side.
: ON
Other than above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D14
10
Ground
5
11
Automatic drive positioner control unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
2
D14
11
Existed
14
10
Revision: 2008 October
2009 Murano
ADP-70
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-205, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch (changeover switch).
Refer to
ADP-70, "CHANGEOVER SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (changeover switch). Refer to
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-40, "Intermittent Incident"
>> INSPECTION END
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000003600952
1.
CHECK CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-66, "Removal and Installation"
MIRROR SWITCH
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
2
Not existed
14
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
10
7
Changeover switch
LEFT
Existed
Other than above
Not existed
11
RIGHT
Existed
Other than above
Not existed
Revision: 2008 October
2009 Murano
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-71
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
MIRROR SWITCH : Description
INFOID:0000000003600953
It operates angle of the door mirror face.
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSITIONER CONTROL UNIT.
MIRROR SWITCH : Component Function Check
INFOID:0000000003600954
1.
CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.
Is the inspection result normal?
YES
>> Mirror switch function is OK.
NO
>> Refer to
ADP-71, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000003600955
1.
CHECK MIRROR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK MIRROR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
MIR CON SW-UP/DN
When operating the mirror switch toward the up or down side.
: ON
Other than above.
: OFF
MIR CON SW-RH/LH
When operating the mirror switch toward the right or left side.
: ON
Other than above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D14
4
Ground
5
12
13
15
Automatic drive positioner control unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
3
D14
15
Existed
4
13
15
12
16
4
Revision: 2008 October
2009 Murano
ADP-72
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-204, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK MIRROR SWITCH
Check door mirror remote control switch (mirror switch).
Refer to
ADP-72, "MIRROR SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (mirror switch). Refer to
.
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-40, "Intermittent Incident"
>> INSPECTION END
MIRROR SWITCH : Component Inspection
INFOID:0000000003600956
1.
CHECK MIRROR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
3
Not existed
4
15
16
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
4
7
Mirror switch
RIGHT
Existed
Other than above
Not existed
13
LEFT
Existed
Other than above
Not existed
15
UP
Existed
Other than above
Not existed
12
DOWN
Existed
Other than above
Not existed
Revision: 2008 October
2009 Murano
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-73
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-66, "Removal and Installation"
Revision: 2008 October
2009 Murano
ADP-74
< COMPONENT DIAGNOSIS >
POWER SEAT SWITCH GROUND CIRCUIT
POWER SEAT SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000003312424
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Check continuity between power seat switch connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace harness or connector.
Power seat switch
Ground
Continuity
Connector
Terminal
B459
35
Existed
Revision: 2008 October
2009 Murano
TILT &TELESCOPIC SWITCH GROUND CIRCUIT
ADP-75
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
TILT &TELESCOPIC SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000003639906
1.
CHECK TILT & TELESCOPIC SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic switch connector.
3.
Check continuity between tilt & telescopic switch and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace harness.
Tilt & telescopic switch
Ground
Continuity
Connector
Terminal
M102
1
Existed
Revision: 2008 October
2009 Murano
ADP-76
< COMPONENT DIAGNOSIS >
FRONT DOOR SWITCH (DRIVER SIDE)
FRONT DOOR SWITCH (DRIVER SIDE)
Description
INFOID:0000000003312432
Detects front door (driver side) open/close condition.
Component Function Check
INFOID:0000000003312433
1.
CHECK FUNCTION
1.
Select “DOOR SW-DR” in “Data monitor” mode with CONSULT-III.
2.
Check the front door switch (driver side) signal under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000003312434
1.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door switch (driver side) connector.
3.
Check signal between BCM connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector and front door switch (driver side) connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
Monitor item
Condition
Status
DOOR SW-DR
Front door switch
(driver side)
Open
ON
Close
OFF
(+)
(–)
Signal
(Reference value)
Front door switch(driver side)
Connector
Terminals
B34
2
Ground
JPMIA0011GB
BCM
Front door switch(driver side)
Continuity
Connector
Terminal
Connector
Terminal
M123
150
B34 2
Existed
BCM
Ground
Continuity
Connector
Terminal
M123
150
Not existed
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст