Nissan Murano Z51 (2008 year). Manual — part 299
PWO-2
< COMPONENT DIAGNOSIS >
CIGARETTE LIGHTER
COMPONENT DIAGNOSIS
CIGARETTE LIGHTER
Wiring Diagram - CIGARETTE LIGHTER -
INFOID:0000000003372920
JCMWM3147GB
Revision: 2008 October
2009 Murano
PWO
CIGARETTE LIGHTER
PWO-3
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3148GB
Revision: 2008 October
2009 Murano
PWO-4
< COMPONENT DIAGNOSIS >
POWER SOCKET
POWER SOCKET
Wiring Diagram - POWER SOCKET -
INFOID:0000000003372921
JCMWM3149GB
Revision: 2008 October
2009 Murano
PWO
POWER SOCKET
PWO-5
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JCMWM3150GB
Revision: 2008 October
2009 Murano
PWO-6
< COMPONENT DIAGNOSIS >
POWER SOCKET
JCMWM3151GB
Revision: 2008 October
2009 Murano
PWO
PRECAUTIONS
PWO-7
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000004770036
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Revision: 2008 October
2009 Murano
PWO-8
< ON-VEHICLE REPAIR >
CIGARETTE LIGHTER
ON-VEHICLE REPAIR
CIGARETTE LIGHTER
Exploded View
INFOID:0000000003372924
Removal and Installation
INFOID:0000000003372925
REMOVAL
1.
Remove console finisher assembly. Refer to
.
2.
Pull out cigarette lighter (1).
3.
Disconnect cigarette lighter connector (A).
4.
Pull out cigarette lighter socket (2) by pushing the cigarette
lighter ring pawl (B) from the cigarette lighter socket hole
(square) (C).
5.
Remove cigarette lighter ring (3) from console finisher assembly
while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of cigarette lighter socket, cigarette lighter ring, and console finisher assembly.
1
: Cigarette lighter
2
: Cigarette lighter socket
3
: Cigarette lighter ring
JPMIA0784ZZ
D
: Cut out
JPMIA0785ZZ
Revision: 2008 October
2009 Murano
PWO
POWER SOCKET
PWO-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER SOCKET
FRONT POWER SOCKET
FRONT POWER SOCKET : Exploded View
INFOID:0000000003372928
FRONT POWER SOCKET : Removal and Installation
INFOID:0000000003372929
REMOVAL
1.
Remove front console pocket. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (B) from the
inner socket hole (square) (C).
4.
Remove ring (2) from front console pocket while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and front console pocket.
CONSOLE POWER SOCKET
CONSOLE POWER SOCKET : Exploded View
INFOID:0000000003372932
Console Power Socket with DVD Player
Console Power Socket without DVD Player
1
: Inner socket
2
: Ring
JPMIA0782ZZ
D
: Cut out
JPMIA0783ZZ
1
: Inner socket
2
: Ring
JPMIA0788ZZ
Revision: 2008 October
2009 Murano
PWO-10
< ON-VEHICLE REPAIR >
POWER SOCKET
CONSOLE POWER SOCKET : Removal and Installation
INFOID:0000000003372933
REMOVAL (WITH DVD PLAYER)
1.
Remove console rear finisher. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (B) from the
inner socket hole (square) (C).
4.
Remove ring (2) from console box while pressing pawls.
REMOVAL (WITHOUT DVD PLAYER)
1.
Remove console finisher assembly. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (B) from the
inner socket hole (square) (C).
4.
Remove ring (2) from console box while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and console box.
LUGGAGE ROOM POWER SOCKET
1
: Inner socket
2
: Ring
JPMIA0786ZZ
D
: Cut out
JPMIA0789ZZ
D
: Cut out
JPMIA0787ZZ
Revision: 2008 October
2009 Murano
PWO
POWER SOCKET
PWO-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
LUGGAGE ROOM POWER SOCKET : Exploded View
INFOID:0000000003372930
LUGGAGE ROOM POWER SOCKET : Removal and Installation
INFOID:0000000003372931
REMOVAL
1.
Remove luggage side finisher lower (RH). Refer to
2.
Disconnect power socket connector (A).
3.
Remove retainer (1) and remove power socket assembly.
4.
Pull out inner socket (2) by pushing the ring pawl (D) from the
inner socket hole (square) (C).
5.
Remove ring (3) from luggage side finisher lower (RH) while
pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and luggage side finisher lower (RH).
1
: Inner socket
2
: Ring
3
: Retainer
JPMIA1299ZZ
B
: Cut out
JPMIA1300ZZ
Revision: 2008 October
2009 Murano
RAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
N
O
P
CONTENTS
REAR AXLE
2WD
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
ON-VEHICLE MAINTENANCE . . . . . .
REAR WHEEL HUB AND HOUSING . . . . .
Inspection . . . . . . . . . . . . . . . . ..
ON-VEHICLE REPAIR . . . . . . . . ..
REAR WHEEL HUB AND HOUSING . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ...
Wheel Bearing . . . . . . . . . . . . . . ...
AWD
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ..
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Commercial Service Tool . . . . . . . . . .
ON-VEHICLE MAINTENANCE . . . . .
REAR WHEEL HUB AND HOUSING . . . ...
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
ON-VEHICLE REPAIR . . . . . . . . .
REAR WHEEL HUB AND HOUSING . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Disassembly and Assembly . . ...
FINAL DRIVE SIDE . . . . . . . . . . . . .
FINAL DRIVE SIDE : Disassembly and Assembly .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Revision: 2008 October
2009 Murano
RAX-2
< SYMPTOM DIAGNOSIS >
[2WD]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000003544416
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
NVH in RAX and RSU sections
NVH in WT
section
NVH in WT
section
NVH in BR
section
Possible cause and SUSPECTED PARTS
Im
pro
per in
st
a
lla
ti
on
,
lo
os
en
es
s
Part
s int
e
rference
Whe
e
l be
ari
n
g
da
m
age
REAR AXLE AND RE
AR SUSPENSI
ON
TIRE
ROA
D
WHEEL
BRAKE
Symptom
REAR AXLE
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
Revision: 2008 October
2009 Murano
PREPARATION
RAX-3
< PREPARATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000003544417
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2008 October
2009 Murano
RAX-4
< ON-VEHICLE MAINTENANCE >
[2WD]
REAR WHEEL HUB AND HOUSING
ON-VEHICLE MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000003544418
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
Revision: 2008 October
2009 Murano
REAR WHEEL HUB AND HOUSING
RAX-5
< ON-VEHICLE REPAIR >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
ON-VEHICLE REPAIR
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000003544438
Removal and Installation
INFOID:0000000003544439
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-115, "REAR WHEEL SENSOR : Exploded
.
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-42, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Never depress brake pedal while caliper assembly is removed.
4.
Remove disc rotor. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
5.
Remove cotter pin, then loosen suspension arm mounting nut of axle housing. Refer to
6.
Remove wheel hub and bearing assembly.
7.
Remove parking brake shoe and parking brake cable from back plate. Refer to
8.
Remove anchor block mounting nuts, and then remove anchor block and back plate from axle housing.
9.
Remove stabilizer connecting rod (upper side) with power tool. Refer to
.
10. Remove radius rod (axle housing side). Refer to
11. Remove coil spring. Refer to
12. Set suitable jack under axle housing.
13. Remove front lower link (shock absorber side) with power tool. Refer to
14. Remove front lower link (axle housing side). Refer to
.
15. Separate suspension arm from axle housing so as not to damage ball joint boot using ball joint remover,
and then remove axle housing from the vehicle.
1.
Ball seat
2.
Bushing
3.
Cotter pin
4.
Axle housing
5.
Back plate
6.
Anchor block
7.
Wheel hub and bearing assembly
Refer to
JPDIG0095GB
Revision: 2008 October
2009 Murano
RAX-6
< ON-VEHICLE REPAIR >
[2WD]
REAR WHEEL HUB AND HOUSING
CAUTION:
Temporarily tighten nuts to prevent damage to threads and to prevent the ball joint remover from
coming off.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and steering knuckle.
• Never reuse cotter pin.
Inspection
INFOID:0000000003544440
INSPECTION AFTER REMOVAL
Wheel Hub and Bearing Assembly
Check the wheel hub and bearing assembly for wear, cracks, and damage. Replace if necessary.
Axle Housing
Check the axle housing for wear, cracks, and damage. Replace if necessary.
Ball Joint Inspection
Check for boot breakage, axial looseness, and torque of suspension arm ball joint. Refer to
.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Adjust parking brake operation (stroke). Refer to
PB-3, "Inspection and Adjustment"
.
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст