Nissan Murano Z51 (2008 year). Manual — part 90
BCM (BODY CONTROL MODULE)
DEF-51
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
NOTE:
• *1: With Intelligent Key system
• *2: Without Intelligent Key system
• *3: With auto light system
• *4: Without BOSE audio system
• *5: With TPMS
Wiring Diagram - BCM -
INFOID:0000000004749674
UP TO VIN: JN8AZ18U*9W100000, JN8AZ18W*9W200000 (EXCEPT FOR MEXICO),
151
(G)
Ground
Rear window defog-
ger relay control
Output
Rear window de-
fogger
Active
0 V
Not activated
Battery voltage
Terminal No.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
Revision: 2008 October
2009 Murano
DEF-52
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
JN8AZ18U*9W710000, JN8AZ18W*9W810000 (FOR MEXICO)
JCMWM3152GB
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
DEF-53
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JCMWM3153GB
Revision: 2008 October
2009 Murano
DEF-54
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
JCMWM3154GB
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
DEF-55
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JCMWM3155GB
Revision: 2008 October
2009 Murano
DEF-56
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
JCMWM3156GB
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
DEF-57
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JCMWM3157GB
Revision: 2008 October
2009 Murano
DEF-58
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
FROM VIN: JN8AZ18U*9W100001, JN8AZ18W*9W200001 (EXCEPT FOR MEXICO),
JCMWM3158GB
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
DEF-59
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JN8AZ18U*9W710001, JN8AZ18W*9W810001 (FOR MEXICO)
JCMWM3159GB
Revision: 2008 October
2009 Murano
DEF-60
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
JCMWM3160GB
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
DEF-61
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JCMWM3161GB
Revision: 2008 October
2009 Murano
DEF-62
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
JCMWM3162GB
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
DEF-63
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JCMWM3163GB
Revision: 2008 October
2009 Murano
DEF-64
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
JCMWM3164GB
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
DEF-65
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
Fail-safe
INFOID:0000000004749675
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
JCMWM3165GB
Revision: 2008 October
2009 Murano
DEF-66
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
Display contents of CONSULT
Fail-safe
Cancellation
B2013: ID DISCORD BCM-S/L
Inhibit engine cranking
Erase DTC
B2014: CHAIN OF S/L-BCM
Inhibit engine cranking
Erase DTC
B2190: NATS ANTENNA AMP
Inhibit engine cranking
Erase DTC
B2191: DIFFERENCE OF KEY
Inhibit engine cranking
Erase DTC
B2192: ID DISCORD BCM-ECM
Inhibit engine cranking
Erase DTC
B2193: CHAIN OF BCM-ECM
Inhibit engine cranking
Erase DTC
B2195: ANTI SCANNING
Inhibit engine cranking
Ignition switch ON
→
OFF
B2557: VEHICLE SPEED
Inhibit steering lock
When normal vehicle speed signals are received from ABS actua-
tor and electric unit (control unit) for 500 ms
B2560: STARTER CONT RELAY
Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
• Starter control relay signal
• Starter relay status signal
B2601: SHIFT POSITION
Inhibit steering lock
500 ms after the following signal reception status becomes consis-
tent
• Selector lever P position switch signal
• P range signal (CAN)
B2602: SHIFT POSITION
Inhibit steering lock
5 seconds after the following BCM recognition conditions are ful-
filled
• Ignition switch is in the ON position
• Selector lever P position switch signal: Except P position (battery
voltage)
• Vehicle speed: 4 km/h (2.5 MPH) or more
B2603: SHIFT POSI STATUS
Inhibit steering lock
500 ms after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
• Selector lever P position switch signal: Except P position (battery
voltage)
• Selector lever P/N position signal: Except P and N positions (0 V)
B2604: PNP SW
Inhibit steering lock
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-
age)
- P range signal or N range signal (CAN): ON
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
B2605: PNP SW
Inhibit steering lock
500 ms after any of the following BCM recognition conditions are
fulfilled
• Ignition switch is in the ON position
- Power position: IGN
- Selector lever P/N position signal: Except P and N positions (0 V)
- Interlock/PNP switch signal (CAN): OFF
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: P or N position (battery volt-
age)
- PNP switch signal (CAN): ON
B2606: S/L RELAY
Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст