Nissan Murano Z51 (2008 year). Manual — part 136
DRIVE PINION
DLN-115
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Assembly
INFOID:0000000003412893
1.
Install a drive pinion adjusting shim of the same thickness as
was installed prior to disassembly. Press pinion rear bearing
outer race into gear carrier, using the drift [SST: ST1713000
(
—
).
CAUTION:
• At first, using a hammer, tap bearing outer race until it
becomes flush to gear carrier.
• Never reuse pinion rear bearing outer race.
2.
Press pinion front bearing outer race into gear carrier, using the
drift [SST: 33230000 (J-25805-01)].
CAUTION:
• At first, using a hammer, tap bearing outer race until it
becomes flush to gear carrier.
• Never reuse pinion front bearing outer race.
3.
Press pinion rear bearing inner race to drive pinion, using the
drift [SST: ST23860000 (
—
)].
CAUTION:
Never reuse pinion rear bearing inner race.
4.
After checking and adjusting the tooth contact and backlash of the drive gear and drive pinion following
the procedure below.
a.
Apply gear oil to the pinion rear bearing, and assemble the drive pinion to the gear carrier.
CAUTION:
Never assemble a collapsible spacer.
b.
Apply gear oil to pinion front bearing, and assemble pinion front
bearing inner race to drive pinion. Using the drifts and stand,
press pinion front bearing inner race to drive pinion as far as
drive pinion nut can be tightened.
CAUTION:
Never reuse pinion front bearing inner race.
c.
Temporarily tighten removed drive pinion nut to drive pinion.
NOTE:
Use removed drive pinion nut only for the preload measurement.
PDIA0056E
PDIA0067E
PDIA0068E
A
: Drift [SST: KV40100610 (J-26089)]
B
: Drift [SST: ST38220000 (
—
)]
C
: Drift [SST: ST23860000 (
—
)]
PDIA0057E
Revision: 2008 October
2009 Murano
DLN-116
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DRIVE PINION
d.
Fit the drive pinion socket (A) [SST: KV38108500 (
—
)]
onto the drive pinion spline. Using the pinion nut wrench (B)
[SST: KV38108400 (
—
)], tighten drive pinion nut to the
specified preload torque.
CAUTION:
Drive pinion nut is tightened with no collapsible spacer. Be
careful not to overtighten it. While measuring the preload,
tighten it by 5
°
to 10
°
.
e.
Apply gear oil to side bearings, and install new side bearing
adjusting shims with the same thickness or re-install the old
ones to the same mounting position they were in prior to disas-
sembly. Set the drifts [SST: KV40100610 (J-26089)] to the right
and left. Install differential case assembly to gear carrier.
CAUTION:
• The drifts shall be placed on the center of the adjusting
shims.
• The pressure shall be as low as possible to install gear
carrier assembly to differential assembly. The maximum
pressure shall be 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).
• If adjusting shims are installed by tapping, gear carrier
may be damaged. Avoid tapping.
f.
Check and adjust the tooth contact. Refer to
g.
Check and adjust the backlash. Refer to
h.
Remove dummy cover set, and remove differential case assembly.
i.
Remove drive pinion nut and press drive pinion assembly out of
gear carrier.
CAUTION:
Never drop drive pinion assembly.
j.
Remove pinion front bearing inner race.
C
: Preload gauge [SST: ST3127S000 (J-25765-A)]
Standard
Pinion bearing preload
: Refer to
.
JSDIA0266ZZ
PDIA0064E
PDIA0445E
Revision: 2008 October
2009 Murano
DRIVE PINION
DLN-117
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
5.
Assemble collapsible spacer to drive pinion.
CAUTION:
• Be careful of the mounting direction of collapsible spacer.
• Never reuse collapsible spacer.
6.
Apply gear oil to pinion front bearing, and assemble pinion front
bearing inner race to drive pinion. Using the drifts and stand,
press pinion front bearing inner race to drive pinion as far as
drive pinion nut can be tightened.
CAUTION:
Never reuse pinion front bearing inner race.
7.
Apply anti-corrosive oil to the thread and seat of drive pinion nut,
and temporarily tighten drive pinion nut to drive pinion.
CAUTION:
Never reuse drive pinion nut.
8.
Fit the drive pinion socket (A) [SST: KV38108500 (
—
)]
onto the drive pinion spline. Using the pinion nut wrench (B)
[SST: KV38108400 (
—
)], adjust the drive pinion nut
tightening torque and pinion bearing preload torque.
CAUTION:
• Adjust the lower limit of the drive pinion nut tightening
torque first.
• If the preload torque exceeds the specified value, replace
collapsible spacer and tighten it again to adjust. Never
loosen drive pinion nut to adjust the preload torque.
• After adjustment, rotate drive pinion back and forth 2 to 3
times to check for unusual noise, rotation malfunction,
and other malfunctions.
9.
Install differential case assembly. Refer to
CAUTION:
Never install rear cover.
10. Install dummy cover set [SST: KV381086S1 (
—
)], and check drive gear runout, tooth contact,
.
11. Remove dummy cover set [SST: KV381086S1 (
—
)], then install rear cover, and side oil seal.
12. Check total preload torque. Refer to
SDIA2525E
A
: Drift [SST: KV40100610 (J-26089)]
B
: Drift [SST: ST38220000 (
—
)]
C
: Drift [SST: ST23860000 (
—
)]
C
: Preload gauge [SST: ST3127S000 (J-25765-A)]
Drive pinion tightening
torque
: Refer to
.
Standard
Pinion bearing preload
: Refer to
PDIA0057E
JSDIA0266ZZ
Revision: 2008 October
2009 Murano
DLN-118
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DRIVE PINION
13. Install electric controlled coupling assembly. Refer to
.
14. Check companion flange runout. Refer to
Adjustment
INFOID:0000000003412894
TOTAL PRELOAD TORQUE
1.
Remove electric controlled coupling assembly. Refer to
2.
Rotate drive pinion back and forth 2 to 3 times to check for unusual noise and rotation malfunction.
3.
Rotate drive pinion at least 20 times to check for smooth opera-
tion of the bearing.
4.
Fit drive pinion socket onto drive pinion spline. Measure the total
preload, using the preload gauge (A) [SST: 3127S000 (J-27565-
A)] and drive pinion socket (B) [SST: KV38108500
—
)].
NOTE:
Total preload torque = Pinion bearing torque + Side bearing
torque
• If measured value is out of the specification, disassemble it to check and adjust each part. Adjust the pinion
bearing preload and side bearing preload.
Adjust the pinion bearing preload first, then adjust the side bearing preload.
DRIVE GEAR RUNOUT
1.
Remove rear cover. Refer to
.
2.
Following the procedure below, install a dummy cover set [SST: KV381086S1 (
—
)] to gear car-
rier.
a.
Set dummy cover shims [SST: KV38108630 (
—
)] to the right and left side bearing adjusting
shims.
b.
Temporarily tighten dummy cover [SST: KV38108610 (
—
)] to gear carrier.
c.
Position dummy cover spacers [SST: KY38108621 (
—
)] to dummy cover [SST: 38108610
(
—
)].
d.
Tighten rear cover mounting bolts to the specified torque. Refer to
.
e.
Tighten dummy cover spacer mounting bolts evenly to the specified torque.
Standard
Total preload torque
: Refer to
When the preload torque is large
On pinion bearings:
Replace the collapsible spacer.
On side bearings:
Use thinner side bearing adjusting shims.
When the preload is small
On pinion bearings:
Tighten the drive pinion nut.
On side bearings:
Use thicker side bearing adjusting shims.
PDIA0048E
: 5.9 N·m (0.6 kg-m, 52 in-lb)
Revision: 2008 October
2009 Murano
DRIVE PINION
DLN-119
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3.
Fit a dial indicator to the drive gear back face.
4.
Rotate the drive gear to measure runout.
• If the runout is outside of the repair limit, check drive gear
assembly condition; foreign material may be caught between
drive gear and differential case, or differential case or drive
gear may be deformed, etc.
CAUTION:
Replace drive gear and drive pinion as a set.
TOOTH CONTACT
1.
Remove rear cover. Refer to
.
2.
Following the procedure below, install a dummy cover set [SST: KV381086S1 (
—
)] to gear car-
rier.
a.
Set dummy cover shims [SST: KV38108630 (
—
)] to the right and left side bearing adjusting
shims.
b.
Temporarily tighten dummy cover [SST: 38108620 (
—
)] to gear carrier.
c.
Position dummy cover spacers [SST: 38108621 (
—
)] to dummy cover [SST: 38108620 (
—
)].
d.
Tighten rear cover mounting bolts to the specified torque. Refer to
e.
Tighten dummy cover spacer mounting bolts evenly to the specified torque.
3.
Apply red lead to drive gear.
CAUTION:
Apply red lead to both the faces of 3 to 4 gears at 4 loca-
tions evenly spaced on drive gear.
4.
Rotate drive gear back and forth several times, check drive pin-
ion gear to drive gear tooth contact.
CAUTION:
Check tooth contact on drive side and reverse side.
Limit
Drive gear back face
runout
: Refer to
PDIA0050E
: 5.9 N·m (0.6 kg-m, 52 in-lb)
PDIA0051E
SDIA0570E
Revision: 2008 October
2009 Murano
DLN-120
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DRIVE PINION
Tooth Contact Judgment Guide
5.
If tooth contact is improperly adjusted, follow the procedure
below to adjust the pinion height (dimension X).
• If the tooth contact is near the face (face contact), or near the
heel (heel contact), thicken drive pinion gear adjusting shim to
move drive pinion closer to drive gear.
SDIA2549E
SDIA0517E
PDIA0440E
Revision: 2008 October
2009 Murano
DRIVE PINION
DLN-121
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• If the tooth contact is near the flank (flank contact), or near the
toe (toe contact), thin drive pinion gear adjusting shim to move
drive pinion farther from drive gear.
BACKLASH
1.
Remove rear cover. Refer to
.
2.
Following the procedure below, install a dummy cover set [SST: KV381086S1 (
—
)] to gear car-
rier.
a.
Set dummy cover shims [SST: KV38108630 (
—
)] to the right and left side bearing adjusting
shims.
b.
Temporarily tighten dummy cover [SST: KV38108610 (
—
)] to gear carrier.
c.
Position dummy cover spacers [SST: KV38108621 (
—
)] to dummy cover [SST: KV38108610
(
—
)].
d.
Tighten rear cover mounting bolts to the specified torque. Refer to
e.
Tighten dummy cover spacer mounting bolts evenly to the specified torque.
3.
Fit a dial indicator to the drive gear face to measure the back-
lash.
• If the backlash is outside of the specified value, change the
thickness of side bearing adjusting shims.
Inspection After Disassembly
INFOID:0000000003691308
DRIVE GEAR AND DRIVE PINION
• Clean up the disassembled parts.
• If the gear teeth never mesh or line-up correctly, determine the cause and adjust or replace as necessary.
• If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new drive
gear and drive pinion as a set.
BEARING
• Clean up the disassembled parts.
• If any chipped (by friction), pitted, worn, rusted or scratched marks, or unusual noise from the bearing is
observed, replace as a bearing assembly (as a new set).
SIDE GEAR AND PINION MATE GEAR
PDIA0441E
: 5.9 N·m (0.6 kg-m, 52 in-lb)
Standard
Backlash
: Refer to
.
When the backlash is large:
Make drive gear back adjusting shims thicker, and drive
gear front adjusting shims thinner.
When the backlash is small:
Make drive gear back adjusting shims thinner, and
drive gear front adjusting shims thicker.
PDIA0049E
Revision: 2008 October
2009 Murano
DLN-122
< DISASSEMBLY AND ASSEMBLY >
[REAR FINAL DRIVE: R145]
DRIVE PINION
• Clean up the disassembled parts.
• If any cracks or damage on the surface of the tooth is found, replace.
• If any worn or chipped mark on the contact sides of the thrust washer is found, replace.
SIDE GEAR THRUST WASHER AND PINION MATE THRUST WASHER
• Clean up the disassembled parts.
• If it is chipped (by friction), damaged, or unusually worn, replace.
OIL SEAL
• Whenever disassembled, replace.
• If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace them.
DIFFERENTIAL CASE
• Clean up the disassembled parts.
• If any wear or crack on the contact sides of the differential case is found, replace.
COMPANION FLANGE
• Clean up the disassembled parts.
• If any chipped mark [about 0.1 mm, (0.004 in)] or other damage on the contact sides of the lips of the com-
panion flange is found, replace.
Revision: 2008 October
2009 Murano
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-123
< SERVICE DATA AND SPECIFICATIONS (SDS)
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000003412896
Drive Gear Runout
INFOID:0000000003412897
Unit: mm (in)
Differential Side Gear Clearance
INFOID:0000000003412898
Unit: mm (in)
Preload Torque
INFOID:0000000003412899
Unit: N·m (kg-m, in-lb)
Backlash
INFOID:0000000003412900
Unit: mm (in)
Companion Flange Runout
INFOID:0000000003412901
Unit: mm (in)
Applied model
AWD
VQ35DE
CVT
Final drive model
R145
Gear ratio
2.466
Number of teeth (Drive gear/Drive pinion)
37/15
Oil capacity (Approx.)
(US pt, lmp pt)
0.55 (1-1/8, 1)
Number of pinion gears
2
Drive pinion adjustment spacer type
Collapsible
Item
Limit
Drive gear back face runout
0.05 (0.0020)
Item
Standard
Side gear backlash (Clearance between side gear and differential
case)
0.2 (0.008) or less
(Each gear should rotate smoothly without excessive resistance
during differential motion.)
Item
Standard
Pinion bearing (P
1
)
0.69 – 1.18 (0.07 – 0.12, 7 – 10)
Side bearing (P
2
)
0.64 – 0.98 (0.07 – 0.09, 6 – 8)
Side bearing to pinion bearing (Total preload)
(Total preload = P
1
+ P
2
)
1.33 – 2.16 (0.14 – 0.22, 12 – 19)
Item
Standard
Drive gear to drive pinion gear
0.10 – 0.15 (0.0039 – 0.0059)
Item
Limit
Companion flange face
0.13 (0.0051)
Inner side of the companion flange
0.19 (0.0075)
Revision: 2008 October
2009 Murano
EC-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
EC
A
EC
N
O
P
CONTENTS
ENGINE CONTROL SYSTEM
VQ35DE
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
Diagnostic Work Sheet . . . . . . . . . . .
INSPECTION AND ADJUSTMENT . . . . .
BASIC INSPECTION . . . . . . . . . . . . .
BASIC INSPECTION : Special Repair Require-
ment . . . . . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . .
IDLE SPEED . . . . . . . . . . . . . . . ..
IDLE SPEED : Description . . . . . . . . . ..
IDLE SPEED : Special Repair Requirement . . ...
IGNITION TIMING . . . . . . . . . . . . . ..
IGNITION TIMING : Description . . . . . . . ..
IGNITION TIMING : Special Repair Requirement
VIN REGISTRATION . . . . . . . . . . . . .
VIN REGISTRATION : Description . . . . . . .
VIN REGISTRATION : Special Repair Require-
ment . . . . . . . . . . . . . . . . . .
ACCELERATOR PEDAL RELEASED POSITION
LEARNING . . . . . . . . . . . . . . . .
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description . . . . . . . . . . .
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement . . . ..
THROTTLE VALVE CLOSED POSITION LEARN-
ING . . . . . . . . . . . . . . . . . . . .
THROTTLE VALVE CLOSED POSITION
LEARNING : Description . . . . . . . . . . .
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement . . . ..
IDLE AIR VOLUME LEARNING . . . . . . . .
IDLE AIR VOLUME LEARNING : Description . . .
IDLE AIR VOLUME LEARNING : Special Repair
Requirement . . . . . . . . . . . . . . .
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR . . . . . . . . . . . . . . . . . ...
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Description . . . . . . . . . . . .
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Special Repair Requirement . . . . . .
FUNCTION DIAGNOSIS . . . . . . . ..
ENGINE CONTROL SYSTEM . . . . . . ..
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . .
Component Description . . . . . . . . . . ...
MULTIPORT FUEL INJECTION SYSTEM . ...
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . .
Component Description . . . . . . . . . . ...
ELECTRIC IGNITION SYSTEM . . . . . .
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . .
Component Description . . . . . . . . . . ...
AIR CONDITIONING CUT CONTROL . . . ..
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ..
Component Parts Location . . . . . . . . .
Component Description . . . . . . . . . . ...
Revision: 2008 October
2009 Murano
EC-2
AUTOMATIC SPEED CONTROL DEVICE
(ASCD) . . . . . . . . . . . . . . . ...
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . ...
Component Description . . . . . . . . . . .
CAN COMMUNICATION . . . . . . . . ...
System Description . . . . . . . . . . . . .
COOLING FAN CONTROL . . . . . . . ...
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . ...
Component Description . . . . . . . . . . ..
ELECTRONIC CONTROLLED ENGINE
MOUNT . . . . . . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . ...
Component Description . . . . . . . . . . .
EVAPORATIVE EMISSION SYSTEM . . . ...
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . ...
Component Description . . . . . . . . . . .
INTAKE VALVE TIMING CONTROL . . . . .
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . ...
Component Description . . . . . . . . . . ..
VARIABLE INDUCTION AIR SYSTEM . . . .
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . ...
Component Description . . . . . . . . . .
ON BOARD DIAGNOSTIC (OBD) SYSTEM ...
Diagnosis Description . . . . . . . . . . .
CONSULT-III Function . . . . . . . . . . ..
Diagnosis Tool Function . . . . . . . . . ..
COMPONENT DIAGNOSIS . . . . . ...
TROUBLE DIAGNOSIS - SPECIFICATION
VALUE . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT ...
Diagnosis Procedure . . . . . . . . . . . .
U0101 CAN COMM CIRCUIT . . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
U0164 CAN COMM CIRCUIT . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
U1000, U1001 CAN COMM CIRCUIT . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0011, P0021 IVT CONTROL . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0031, P0032, P0051, P0052 A/F SENSOR 1
HEATER . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0037, P0038, P0057, P0058 HO2S2 HEAT-
ER . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0075, P0081 IVT CONTROL SOLENOID
VALVE . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0101 MAF SENSOR . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0102, P0103 MAF SENSOR . . . . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0112, P0113 IAT SENSOR . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0116 ECT SENSOR . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
Revision: 2008 October
2009 Murano
EC-3
C
D
E
F
G
H
I
J
K
L
M
EC
A
N
O
P
P0117, P0118 ECT SENSOR . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0122, P0123 TP SENSOR . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
Special Repair Requirement . . . . . . . . .
P0125 ECT SENSOR . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0127 IAT SENSOR . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0128 THERMOSTAT FUNCTION . . . . ..
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0130, P0150 A/F SENSOR 1 . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P0131, P0151 A/F SENSOR 1 . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0132, P0152 A/F SENSOR 1 . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0133, P0153 A/F SENSOR 1 . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0137, P0157 HO2S2 . . . . . . . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0138, P0158 HO2S2 . . . . . . . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0139, P0159 HO2S2 . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P0181 FTT SENSOR . . . . . . . . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0182, P0183 FTT SENSOR . . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0196 EOT SENSOR . . . . . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0197, P0198 EOT SENSOR . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0222, P0223 TP SENSOR . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
Special Repair Requirement . . . . . . . . ..
P0300, P0301, P0302, P0303, P0304, P0305,
P0306 MISFIRE . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P0327, P0328, P0332, P0333 KS . . . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Revision: 2008 October
2009 Murano
EC-4
Component Inspection . . . . . . . . . . ...
P0335 CKP SENSOR (POS) . . . . . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0340, P0345 CMP SENSOR (PHASE) . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0420, P0430 THREE WAY CATALYST
FUNCTION . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P0441 EVAP CONTROL SYSTEM . . . . ..
DTC Logic . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P0442 EVAP CONTROL SYSTEM . . . . ..
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE . . . . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0444, P0445 EVAP CANISTER PURGE
VOLUME CONTROL SOLENOID VALVE . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0447 EVAP CANISTER VENT CONTROL
VALVE . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0448 EVAP CANISTER VENT CONTROL
VALVE . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P0451 EVAP CONTROL SYSTEM PRES-
SURE SENSOR . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0452 EVAP CONTROL SYSTEM PRES-
SURE SENSOR . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0453 EVAP CONTROL SYSTEM PRES-
SURE SENSOR . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0455 EVAP CONTROL SYSTEM . . . . ..
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0456 EVAP CONTROL SYSTEM . . . . ..
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0460 FUEL LEVEL SENSOR . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0461 FUEL LEVEL SENSOR . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0462, P0463 FUEL LEVEL SENSOR . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0500 VSS . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0506 ISC SYSTEM . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0507 ISC SYSTEM . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Revision: 2008 October
2009 Murano
EC-5
C
D
E
F
G
H
I
J
K
L
M
EC
A
N
O
P
P0550 PSP SENSOR . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
P0603 ECM POWER SUPPLY . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0605 ECM . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0607 ECM . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0643 SENSOR POWER SUPPLY . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P0850 PNP SWITCH . . . . . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P1148, P1168 CLOSED LOOP CONTROL . .
DTC Logic . . . . . . . . . . . . . . . .
P1212 TCS COMMUNICATION LINE . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P1217 ENGINE OVER TEMPERATURE . . .
DTC Logic . . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P1225 TP SENSOR . . . . . . . . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Special Repair Requirement . . . . . . . . .
P1226 TP SENSOR . . . . . . . . . . ..
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Special Repair Requirement . . . . . . . . .
P1421 COLD START CONTROL . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
P1550 BATTERY CURRENT SENSOR . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P1551, P1552 BATTERY CURRENT SEN-
SOR . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P1553 BATTERY CURRENT SENSOR . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P1554 BATTERY CURRENT SENSOR . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P1564 ASCD STEERING SWITCH . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P1572 ASCD BRAKE SWITCH . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection (ASCD Brake Switch) . ...
Component Inspection (Stop Lamp Switch) . . ..
P1574 ASCD VEHICLE SPEED SENSOR . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P1700 CVT CONTROL SYSTEM . . . . .
Description . . . . . . . . . . . . . . . .
P1715 INPUT SPEED SENSOR (PRIMARY
SPEED SENSOR) . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P1720 VSS . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P1800 VIAS CONTROL SOLENOID VALVE 1 .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Revision: 2008 October
2009 Murano
EC-6
Component Inspection . . . . . . . . . . ...
P1801 VIAS CONTROL SOLENOID VALVE 2 .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
P1805 BRAKE SWITCH . . . . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection (Stop Lamp Switch) . . ..
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
Special Repair Requirement . . . . . . . . ..
P2118 THROTTLE CONTROL MOTOR . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
Special Repair Requirement . . . . . . . . ..
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Special Repair Requirement . . . . . . . . ..
P2122, P2123 APP SENSOR . . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
Special Repair Requirement . . . . . . . . ..
P2127, P2128 APP SENSOR . . . . . . ..
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
Special Repair Requirement . . . . . . . . ..
P2135 TP SENSOR . . . . . . . . . . .
Description . . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ...
Special Repair Requirement . . . . . . . . .
P2138 APP SENSOR . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
Special Repair Requirement . . . . . . . . .
P2A00, P2A03 A/F SENSOR 1 . . . . . .
Description . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
ASCD BRAKE SWITCH . . . . . . . . ...
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection (ASCD Brake Switch) . ...
ASCD INDICATOR . . . . . . . . . . ...
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
COOLING FAN . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection (Cooling Fan Motor) . . .
Component Inspection (Cooling Fan Relay) . . .
ELECTRICAL LOAD SIGNAL . . . . . . ..
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
ELECTRONIC CONTROLLED ENGINE
MOUNT . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
FUEL INJECTOR . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
FUEL PUMP . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection (Fuel Pump) . . . . . .
Component Inspection (Condenser) . . . . . .
IGNITION SIGNAL . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Revision: 2008 October
2009 Murano
EC-7
C
D
E
F
G
H
I
J
K
L
M
EC
A
N
O
P
Component Inspection (Ignition Coil with Power
Transistor) . . . . . . . . . . . . . . . .
Component Inspection (Condenser) . . . . . .
MALFUNCTION INDICATOR LAMP . . . ...
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
POSITIVE CRANKCASE VENTILATION . .
Description . . . . . . . . . . . . . . .
Component Inspection . . . . . . . . . . ..
REFRIGERANT PRESSURE SENSOR . . ...
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
VARIABLE INDUCTION AIR SYSTEM . . .
Description . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . .
ECU DIAGNOSIS . . . . . . . . . ...
ECM . . . . . . . . . . . . . . . . ..
Reference Value . . . . . . . . . . . . ...
Wiring Diagram—ENGINE CONTROL SYS-
TEM— . . . . . . . . . . . . . . . . ...
Fail-safe . . . . . . . . . . . . . . . .
DTC Inspection Priority Chart . . . . . . . .
DTC Index . . . . . . . . . . . . . . .
How to Set SRT Code . . . . . . . . . .
Test Value and Test Limit . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . .
ENGINE CONTROL SYSTEM SYMPTOMS .
Symptom Table . . . . . . . . . . . . . .
NORMAL OPERATING CONDITION . . . .
Description . . . . . . . . . . . . . . . .
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . ...
Precautions For Xenon Headlamp Service . . ...
Precaution for Procedure without Cowl Top Cover ..
On Board Diagnostic (OBD) System of Engine
and CVT . . . . . . . . . . . . . . . .
General Precautions . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . .
ON-VEHICLE MAINTENANCE . . . . ..
FUEL PRESSURE . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
EVAP LEAK CHECK . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . ..
ON-VEHICLE REPAIR . . . . . . . ...
EVAP CANISTER . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . ...
Idle Speed . . . . . . . . . . . . . . . .
Ignition Timing . . . . . . . . . . . . . ...
Calculated Load Value . . . . . . . . . . ..
Mass Air Flow Sensor . . . . . . . . . . .
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст