Nissan Murano Z51 (2008 year). Manual — part 201
EXL-324
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000003261469
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp (HI) is not
turned ON.
One side
• Fuse
• Halogen bulb (HI)
• Harness between IPDM E/R
and the headlamp high
• IPDM E/R
Headlamp (HI) circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
Headlamp (HI) is not
turned OFF.
When ignition switch is
turned ON.
When ignition switch is
turned OFF.
IPDM E/R
—
High beam indicator lamp is not turned ON.
[The headlamp (HI) is turned ON.]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEAD LAMP)
Active test “HEADLAMP”
Headlamp (LO) is not
turned ON.
One side
• Fuse
• Halogen bulb (LO)
• Harness between IPDM E/R
and the headlamp low
• IPDM E/R
Headlamp (LO) circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
Headlamp (LO) is not
turned OFF.
When ignition switch is
turned ON.
When ignition switch is
turned OFF.
IPDM E/R
—
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R
and the front fog lamp
• Front fog lamp
• IPDM E/R
Front fog lamp circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
Front fog lamp is not turned ON.
Parking lamp is not turned ON.
• Parking lamp bulb
• Harness between IPDM E/R
and the front combination lamp
• Front combination lamp
• IPDM E/R
Parking lamp circuit
Refer to
Front side marker lamp is not turned ON.
• Front side marker lamp bulb
• Harness between IPDM E/R
and the front side marker lamp
• IPDM E/R
Front side marker lamp circuit
Refer to
Parking lamp and front side marker lamp are not
turned ON.
• Fuse
• Harness between IPDM E/R
and the front combination lamp
• IPDM E/R
Parking lamp circuit
Refer to
Revision: 2008 October
2009 Murano
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-325
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Tail lamp is not turned ON.
• Harness between IPDM E/R
and the rear combination lamp
• Rear combination lamp
Tail lamp circuit
Refer to
.
License plate lamp is not turned ON.
• License plate lamp bulb
• Harness between IPDM E/R
and the license plate lamp
• License plate lamp
License plate lamp circuit
Refer to
.
Tail lamp and the license plate lamp are not turned
ON.
• Fuse
• Harness between IPDM E/R
and the rear combination lamp
• IPDM E/R
License plate lamp circuit
Refer to
.
• Parking lamp, tail lamp, side marker lamp and li-
cense plate lamp are not turned ON.
• Parking lamp, tail lamp, side marker lamp and li-
cense plate lamp are not turned OFF.
(Each illumination is turned ON/OFF.)
Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED
ON”
Refer to
Tail lamp indicator is not turned ON.
(Parking, tail lamps are turned ON.)
Combination meter
• Combination meter
Data monitor “LIGHT IND”
• BCM (HEAD LAMP)
Active test “TAIL LAMP”
Turn signal lamp does not
blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)
• Harness between BCM and
each turn signal lamp
• Turn signal lamp bulb
Turn signal circuit
Refer to
.
Indicator lamp is includ-
ed.
• Combination switch
• Harness between the combina-
tion switch and BCM
• BCM
Combination switch
Refer to
.
Turn signal indicator lamp
does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn indicator signal
- BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF)
• Combination meter power sup-
ply and the ground circuit
• Combination meter
Combination meter
Power supply and the ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between the hazard
switch and BCM
• BCM
Hazard switch
Refer to
.
Symptom
Possible cause
Inspection item
Revision: 2008 October
2009 Murano
EXL-326
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
Description
INFOID:0000000003261470
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure
INFOID:0000000003261471
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “HL HI REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
3.
HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to
EXL-216, "Component Function Check"
Is the headlamp (HI) circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
On
LO
Off
Revision: 2008 October
2009 Murano
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-327
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000003261472
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000003261473
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “HL LO REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
.
3.
HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to
EXL-218, "Component Function Check"
Is the headlamp (LO) circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
On
OFF
Off
Revision: 2008 October
2009 Murano
EXL-328
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
Description
INFOID:0000000003729589
The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000003729590
1.
CHECK FUSE
Check that the following fuse is fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> GO TO 2.
2.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 4.
NO
>> Replace BCM. Refer to
4.
TAIL LAMP CIRCUIT INSPECTION
Check the tail lamp circuit. Refer to
EXL-231, "Component Function Check"
.
Is the tail lamp circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Unit
Location
Fuse No.
Capacity
• Parking lamp
• Front side marker lamp
IPDM E/R
#52
10 A
• Tail lamp
• License plate lamp
• Rear side marker lamp
#53
10 A
Monitor item
Condition
Monitor status
TAIL & CLR
REQ
Lighting switch
1ST
On
OFF
Off
Revision: 2008 October
2009 Murano
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-329
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000003729591
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000003729592
1.
CHECK FUSE
Check that the following fuse is fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> GO TO 2.
2.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “FR FOG REQ” of IPDM E/R data monitor item.
2.
With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 4.
NO
>> Replace BCM. Refer to
.
4.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
EXL-220, "Component Function Check"
.
Is the front fog lamp circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#58
15 A
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
On
OFF
Off
Revision: 2008 October
2009 Murano
EXL-330
< PRECAUTION >
[HALOGEN TYPE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000003486629
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
INFOID:0000000003486631
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
Revision: 2008 October
2009 Murano
PRECAUTIONS
EXL-331
< PRECAUTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Revision: 2008 October
2009 Murano
EXL-332
< ON-VEHICLE MAINTENANCE >
[HALOGEN TYPE]
HEADLAMP AIMING ADJUSTMENT
ON-VEHICLE MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000003261480
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the front combination lamp assembly has
been replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JPLIA0828ZZ
A.
Headlamp RH (UP/DOWN) adjust-
ment screw
B.
Headlamp LH (UP/DOWN) adjust-
ment screw
: Vehicle center
Revision: 2008 October
2009 Murano
HEADLAMP AIMING ADJUSTMENT
EXL-333
< ON-VEHICLE MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Aiming Adjustment Procedure
INFOID:0000000003261481
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp bulb center and the
screen.
3.
Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).
Low beam distribution on the screen
5.
Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
Side view
Adjustment screw
Screw driver rotation
Facing direction
A
Headlamp RH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
B
Headlamp LH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
Light axis measurement range (R)
: 350
±
175 mm (13.78
±
6.89 in)
JSLIA0005ZZ
Horizontal center line of headlamp (H)
Highest cutoff line height (M)
Lowest cutoff line height (N)
700 (27.56) or less
4 (0.16)
30 (1.18)
701(27.60) – 800 (31.50)
4 (0.16)
30 (1.18)
801 (31.54) or more
17 (0.67)
44 (1.73)
JSLIA0006ZZ
Revision: 2008 October
2009 Murano
EXL-334
< ON-VEHICLE MAINTENANCE >
[HALOGEN TYPE]
HEADLAMP AIMING ADJUSTMENT
Distance between the headlamp
center and the screen (L)
: 10 m (32.8 ft)
Revision: 2008 October
2009 Murano
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-335
< ON-VEHICLE MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000003729593
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000003729594
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4.
Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
A: UP
B: DOWN
JPLIA0811ZZ
JPLIA0008ZZ
Revision: 2008 October
2009 Murano
EXL-336
< ON-VEHICLE MAINTENANCE >
[HALOGEN TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
Revision: 2008 October
2009 Murano
FRONT COMBINATION LAMP
EXL-337
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
ON-VEHICLE REPAIR
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000003261484
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003261485
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Front combination lamp
2.
Headlamp extension panel
JPLIA0812ZZ
1.
Front side marker lamp bulb
2.
Front side marker lamp bulb socket
3.
Halogen bulb (LO)
4.
Halogen bulb (HI)
5.
Front turn signal/parking lamp bulb socket 6.
Front turn signal/parking lamp bulb
7.
Headlamp housing assembly
JPLIA0829ZZ
Revision: 2008 October
2009 Murano
EXL-338
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
FRONT COMBINATION LAMP
1.
Remove the front grille. Refer to
2.
Remove the headlamp extension panel.
3.
Remove the front bumper fascia. Refer to
.
4.
Remove the headlamp mounting bolts.
5.
Remove the harness clips from the headlamp housing.
6.
Pull out the headlamp assembly forward the vehicle.
7.
Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000003261486
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1.
Remove the fender rubber protector in the engine room.
2.
Rotate the bulb counterclockwise and unlock it.
3.
Disconnect the headlamp bulb connector.
4.
Remove the bulb from the headlamp housing assembly.
HEADLAMP BULB (HI)
1.
Rotate the bulb counterclockwise and unlock it.
2.
Disconnect the headlamp bulb connector.
3.
Remove the bulb from the headlamp housing assembly.
FRONT TURN SIGNAL/PARKING LAMP BULB
1.
Remove the front grille. Refer to
2.
Rotate the front turn signal/parking lamp bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the front turn signal/parking lamp bulb socket.
FRONT SIDE MARKER LAMP BULB
1.
Remove the fender rubber protector in the engine room.
2.
Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the front side marker lamp bulb socket.
Disassembly and Assembly
INFOID:0000000003261487
DISASSEMBLY
1.
Rotate the headlamp bulb (LO) counterclockwise and unlock it
2.
Disconnect the headlamp bulb (LO) connector. And remove the bulb from the headlamp housing assem-
bly.
3.
Rotate the headlamp bulb (HI) counterclockwise and unlock it
4.
Disconnect the headlamp bulb (HI) connector. And remove the bulb from the headlamp housing assem-
bly.
5.
Rotate the front turn signal/parking lamp bulb socket counterclockwise and unlock it.
6.
Remove the bulb from the front turn signal/parking lamp bulb socket.
7.
Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
Revision: 2008 October
2009 Murano
FRONT COMBINATION LAMP
EXL-339
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
8.
Remove the bulb from the front side marker lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст