Nissan Murano Z51 (2008 year). Manual — part 307
SUNROOF UNIT ASSEMBLY
RF-97
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
DISASSEMBLY
13. Sunshade motor assembly
Refer to
1.
Windshield glass
2.
Front sunroof glass
3.
Adhesive
4.
Sunroof frame
5.
Roof panel
6.
Primer
7.
Roof side finisher
8.
Rear sunroof glass
Refer to
JMKIA1898GB
Revision: 2008 October
2009 Murano
RF-98
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
Removal and Installation
INFOID:0000000003465804
REMOVAL
CAUTION:
• Always work with a helper.
• When taking sunroof unit assembly out, use cloths to protect the seats and trim from damage.
• Never reuse the front and rear sunroof glass which has been removed once.
1.
Remove the headlining. Refer to
INT-29, "SUNROOF : Removal and Installation"
2.
Remove the glass lid. Refer to
RF-90, "Removal and Installation"
3.
Disconnect drain hoses.
4.
Remove the sunroof brackets (LH/RH).
5.
Remove nuts and bolts from the front end, side rail and rear end.
1.
Weather-strip
2.
Wind deflector
3.
Sunroof frame
4.
Front sunshade
5.
Sunshade cover
6.
Rear sunshade
Refer to
for symbols in the figure.
JMKIA1902ZZ
Revision: 2008 October
2009 Murano
SUNROOF UNIT ASSEMBLY
RF-99
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
6.
Point matching marks on body before removing the sunroof unit assembly.
7.
Apply protective tape around the roof panel to protect the surface from damage.
8.
Remove the front sunroof glass. Refer to
RF-101, "Removal and Installation"
9.
Cut adhesive.
• Cut the adhesibe using windshield cutter (A).
• Pass piano wire though the adhesive with a wire pierce.
• Tie piano wire both ends to wire grip.
• Pull piano wire in turn and cut off adhesive.
10. Remove sunroof unit assembly from vehicle.
INSTALLATION
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
CAUTION:
After installing the sunroof unit assembly and glass lid, perform the leak test and check that there is
no malfunction.
NOTE:
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions fur-
nished with it.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
1.
Using a knife or spatula, trim the adhesive (sealant) remaining
on body down to approximately 2 mm (0.08 in) thick (a) so that
the contour becomes smooth.
CAUTION:
If bonded area on body is scratched, be sure to repair it
with a 2-component urethane. Never use lacquer.
2.
Clean bonded area on sunroof frame with white gasoline.
3.
Apply paint primer along the entire circumference of sunroof frame.
CAUTION:
There are 2 types of primer. Never confuse the application methods.
Paint primer: for painted surfaces
Glass primer: for glass
4.
Apply paint primer on areas where adhesive contacts on the side of vehicle body.
CAUTION:
If paint primer adheres to a painted surface other than bonding area, or if it overflows, quickly
remove it with white gasoline.
PIIB3505J
JMKIA0307ZZ
Revision: 2008 October
2009 Murano
RF-100
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
5.
After applying primers, apply the adhesive along the entire circumference of the sunroof unit assembly as
shown in the figure, and within the time specified in the instructions for the adhesive.
Open adhesive by cutting off the nozzle tip and set it in a sealant gun.
6.
Align mating marks on body and sunroof unit assembly. Install sunroof unit assembly to the body.
7.
Press entire surface of sunroof unit assembly lightly to fit it completely.
8.
Using a spatula, repair any adhesive overflow or shortage to make the surface smooth.
9.
Remove protective tape.
10. Temporarily tighten the mounting bolts and nuts to the of sunroof unit assembly.
11. Tighten the installation points diagonally excluding the installation point of the sunroof bracket around the
roof opening.
12. Tighten the mounting bolts and nuts to the sunroof bracket.
13. Connect drain hoses.
14. Install the glass lid. Refer to
RF-90, "Removal and Installation"
.
NOTE:
After installation, carry out fitting adjustment.Refer to
15. Install the headlining. Refer to
INT-29, "SUNROOF : Removal and Installation"
.
16. Check for water leaks.
NOTE:
• Perform the water leakage check more than 2 hours after sunroof unit assembly installation.
• After glass lid fitting adjustment, carry out water leakage check by spreading water in the whole roof.
Disassembly and Assembly
INFOID:0000000003465805
DISASSEMBLY
1.
Remove the wind deflector. Refer to
RF-107, "Removal and Installation"
2.
Remove the front sunshade and rear sunshade. Refer to
RF-109, "Removal and Installation"
.
ASSEMBLY
Assemble in the reverse order of disassembly.
Revision: 2008 October
2009 Murano
FRONT SUNROOF GLASS
RF-101
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
FRONT SUNROOF GLASS
Exploded View
INFOID:0000000003468558
Removal and Installation
INFOID:0000000003468559
REMOVAL
1.
Remove the roof rail assembly. Refer to
EXT-28, "Removal and Installation"
2.
Remove the roof side finisher. Refer to
RF-90, "Removal and Installation"
.
3.
Fully open the glass lid.
4.
Paint matching marks on body before removeing the front sunroof glass.
5.
Apply protective tape around the roof panel and front sunroof glass to protect the surface from damage.
1.
Front sunroof glass
2.
Adhesive
3.
Windshield glass
4.
Sunroof frame
5.
Primer
6.
Weather-strip
Refer to
JMKIA1899GB
Revision: 2008 October
2009 Murano
RF-102
< ON-VEHICLE REPAIR >
FRONT SUNROOF GLASS
6.
Remove weather-strip.
7.
Cut adhesive.
• Pass piano wire though the adhesive the adhesive with a wire pierce.
• Tie piano wire both ends to wire grip.
• Pull piano wire in turn and cut off adhesive.
8.
Remove front sunroof glass from vehicle using suction lifter.
WARNING:
Always wear safety glasses and heavy gloves to help prevent glass splinters from entering your eyes
or cutting your hands when cutting the glass from the vehicle.
CAUTION:
Never reuse the front sunroof glass which has been removed once.
INSTALLATION
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
NOTE:
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions fur-
nished with it.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
1.
Using a knife or spatula, trim the adhesive (sealant) remaining
on body down to approximately 2 mm (0.08 in) thick (a) so that
the contour becomes smooth.
CAUTION:
If bonded area on body is scratched, be sure to repair it
with a 2-component urethane. Never use lacquer.
2.
Clean bonded area on glass with white gasoline.
3.
Apply glass primer along the entire circumference of glass.
CAUTION:
There are 2 types of primer. Never confuse the application methods.
Paint primer: for painted surfaces
Glass primer: for glass
4.
Apply paint primer on areas where adhesive contacts on the side of sunroof frame.
CAUTION:
If paint primer adheres to a painted surface other than bonding area, or if it overflows, quickly
remove it with white gasoline.
5.
After applying primers, apply the adhesive along the entire circumference of the glass as shown in the fig-
ure, and within the time specified in the instructions for the adhesive.
• Open adhesive by cutting off the nozzle tip and set it in a sealant gun.
6.
After setting suction lifter to glass, align mating marks on sunroof frame and glass. Install glass to the sun-
roof frame.
JMKIA0307ZZ
Revision: 2008 October
2009 Murano
FRONT SUNROOF GLASS
RF-103
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
7.
Press glass till positioning ribs (1) faces with a sunroof frame
(2).
8.
Using a spatula, repair any adhesive overflow or shortage to make the surface smooth.
9.
Remove protective tape.
10. Install roof side finisher. Refer to
RF-90, "Removal and Installation"
11. Install roof rail assembly. Refer to
EXT-28, "Removal and Installation"
JMKIA1930ZZ
Revision: 2008 October
2009 Murano
RF-104
< ON-VEHICLE REPAIR >
REAR SUNROOF GLASS
REAR SUNROOF GLASS
Exploded View
INFOID:0000000003468560
Removal and Installation
INFOID:0000000003468561
REMOVAL
1.
Remove the roof rail assembly. Refer to
EXT-28, "Removal and Installation"
2.
Remove the roof side finisher. Refer to
RF-90, "Removal and Installation"
3.
Remove the glass lid. Refer to
RF-90, "Removal and Installation"
4.
Paint matching marks on body before removing the rear sunroof glass.
5.
Apply protective tape around the roof panel and sunroof unit to protect the surface from damage.
1.
Rear sunroof glass
2.
Adhesive
3.
Sunroof frame
4.
Primer
5.
Roof panel
6.
Weather-strip
Refer to
for symbols in the figure.
JMKIA1900GB
Revision: 2008 October
2009 Murano
REAR SUNROOF GLASS
RF-105
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
6.
Remove weather-strip.
7.
Cut adhesive.
• Pass piano wire though the adhesive with a wire pierce.
• Tie piano wire both ends to wire grip.
• Pull piano wire in turn and cut off adhesive.
8.
Remove rear sunroof glass from vehicle using suction lifter.
WARNING:
Always wear safety glasses and heavy gloves to help prevent glass splinters from entering your eyes
or cutting your hands when cutting the glass from the vehicle.
CAUTION:
Never reuse the rear sunroof glass which has been removed once.
INSTALLATION
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
CAUTION:
After installing the rear sunroof glass, perform the leak test and check that there is no malfunction.
NOTE:
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions fur-
nished with it.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
1.
Using a knife or spatula, trim the adhesive (sealant) remaining
on body down to approximately 2 mm (0.08 in) thick (a) so that
the contour becomes smooth.
CAUTION:
If bonded area on body is scratched, be sure to repair it
with a 2-component urethane. Never use lacquer.
2.
Clean bonded area on glass with white gasoline.
3.
Apply glass primer along the entire circumference of glass.
CAUTION:
There are 2 types of primer. Never confuse the application methods.
Paint primer: for painted surfaces
Glass primer: for glass
4.
Apply paint primer on areas where adhesive contacts on the side of sunroof fram.
CAUTION:
If paint primer adheres to a painted surface other than bonding area, or if it overflows, quickly
remove it with white gasoline.
5.
After applying primers, apply the adhesive along the entire circumference of the glass as shown in the fig-
ure, and within the time specified in the instructions for the adhesive.
Open adhesive by cutting off the nozzle tip and set it in a sealant gun.
6.
After setting suction lifter to glass, align mating marks on sunroof fram and glass. Install glass to the sun-
roof fram.
JMKIA0307ZZ
Revision: 2008 October
2009 Murano
RF-106
< ON-VEHICLE REPAIR >
REAR SUNROOF GLASS
7.
Press glass till positioning ribs (1) faces with a sunroof frame
(2).
8.
Using a spatula, repair any adhesive overflow or shortage to make the surface smooth.
9.
Remove protective tape.
10. Install glass lid. Refer to
RF-90, "Removal and Installation"
11. Install roof side finisher. Refer to
RF-90, "Removal and Installation"
12. Install roof rail assembly. Refer to
EXT-28, "Removal and Installation"
13. Check for water leaks.
NOTE:
• Perform the water leakage check more than 2 hours after rear sunroof glass installation.
• After glass lid fitting adjustment, carry out water leakage check by spreading water in the whole roof.
JMKIA1931ZZ
Revision: 2008 October
2009 Murano
WIND DEFLECTOR
RF-107
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
WIND DEFLECTOR
Exploded View
INFOID:0000000003486696
Removal and Installation
INFOID:0000000003486695
REMOVAL
1.
Fully open the glass lid.
2.
Remove the wind deflector.
1.
Weather-strip
2.
Wind deflector
3.
Sunroof frame
4.
Front sunshade
5.
Sunshade cover
6.
Rear sunshade
Refer to
JMKIA1902ZZ
Revision: 2008 October
2009 Murano
RF-108
< ON-VEHICLE REPAIR >
WIND DEFLECTOR
• Push and slide the fastener as shown by the arrows (1) and
(2) in the figure to remove.
• Remove the screws (A), and then remove wind deflector (1).
INSTALLATION
Install in the reverse order of removal.
: Vehicle front
JMKIA2192ZZ
: Vehicle front
JMKIA1912ZZ
Revision: 2008 October
2009 Murano
SUNSHADE
RF-109
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNSHADE
Exploded View
INFOID:0000000003465806
Removal and Installation
INFOID:0000000003465807
REMOVAL
1.
Remove the headlining. Refer to
INT-29, "SUNROOF : Removal and Installation"
2.
Remove the sunshade cover.
• Remove the sunroof brackets (LH/RH).
• Remove the screw, and then sunshade cover.
3.
Remove the front sunshade and rear sunshade.
1.
Weather-strip
2.
Wind deflector
3.
Sunroof frame
4.
Front sunshade
5.
Sunshade cover
6.
Rear sunshade
Refer to
JMKIA1902ZZ
Revision: 2008 October
2009 Murano
RF-110
< ON-VEHICLE REPAIR >
SUNSHADE
Remove it to the lower part while pushing a front sunshade (1)
and rear sunshade (2) to the arrow direction of the figure.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be careful not to release the spring when installing the sunshade.
JMKIA1910ZZ
Revision: 2008 October
2009 Murano
SUNROOF SWITCH
RF-111
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF SWITCH
Exploded View
INFOID:0000000003443433
INT-29, "SUNROOF : Exploded View"
Removal and Installation
INFOID:0000000003443434
Removal
Remove the sunroof switch. Refer to
INT-29, "SUNROOF : Removal and Installation"
Installation
Install in the reverse order of removal.
Revision: 2008 October
2009 Murano
RSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
RSU
A
B
RSU
N
O
P
CONTENTS
REAR SUSPENSION
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Suspension . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
ON-VEHICLE MAINTENANCE . . . . . .
REAR SUSPENSION ASSEMBLY . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
WHEEL ALIGNMENT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . . ....
ON-VEHICLE REPAIR . . . . . . . . ..
REAR LOWER LINK & COIL SPRING . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
REAR SHOCK ABSORBER . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ..
RADIUS ROD . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
FRONT LOWER LINK . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR STABILIZER . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR SUSPENSION ARM . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
REAR SUSPENSION MEMBER . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
APPLICATION NOTICE . . . . . . . . . . . .
APPLICATION NOTICE : How to Check Vehicle
Type . . . . . . . . . . . . . . . . . . .
TYPE A . . . . . . . . . . . . . . . . . ...
TYPE A : Wheel Alignment . . . . . . . . . ..
TYPE A : Ball Joint . . . . . . . . . . . . ..
TYPE A : Wheelarch Height . . . . . . . . .
TYPE B . . . . . . . . . . . . . . . . . ...
TYPE B : Wheel Alignment . . . . . . . . . ..
TYPE B : Ball Joint . . . . . . . . . . . . ..
TYPE B : Wheelarch Height . . . . . . . . .
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст