Nissan Murano Z51 (2008 year). Manual — part 63
AV
GPS ANTENNA
AV-781
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Removal and Installation
INFOID:0000000003356734
REMOVAL
1.
Remove combination meter. Refer to
.
2.
Disconnect GPS antenna connector from AV control unit.
3.
Remove GPS antenna (1) from instrument panel.
INSTALLATION
Install in the reverse order of removal.
JPNIA0804ZZ
Revision: 2008 October
2009 Murano
AV-782
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT
Exploded View
INFOID:0000000003356735
Removal and Installation
INFOID:0000000003356736
REMOVAL
1.
Remove luggage side finisher lower (RH). Refer to
2.
Remove camera control unit screws, disconnect camera control unit connector and remove the camera
control unit.
INSTALLATION
Install in the reverse order of removal.
Adjustment
INFOID:0000000003356737
ADJUSTMENT
There may be a misalignment of possible route line center position of rear view monitor after removing camera
control unit. Therefore, correct neutral position with the following procedure.
1.
Steer the steering wheel to the leftmost and rightmost ends.
2.
Drive vehicle at 30 km/h (18.6 MPH) min. speed at least 100 m (328.1 ft).
JPNIA0796ZZ
1.
Camera control unit
Revision: 2008 October
2009 Murano
AV
REAR VIEW CAMERA
AV-783
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REAR VIEW CAMERA
Exploded View
INFOID:0000000003356738
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003356739
REMOVAL
1.
Remove back door finisher inner. Refer to
2.
Remove finisher.
3.
Remove rear view camera screws, disconnect rear view camera connector and remove rear view camera
from back door assembly.
INSTALLATION
Install in the reverse order of removal.
Adjustment
INFOID:0000000003356740
Adjust the guide line position if the guide line position is shifted after installing the rear view camera.
1.
Rear view camera
2.
Finisher
JPNIA0797ZZ
Revision: 2008 October
2009 Murano
AV-784
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
REAR VIEW CAMERA
1.
Draw lines on rearward area of the vehicle passing through the
following points: 200 mm (7.87 in) from both sides of the vehicle,
and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the
bumper.
2.
Set into “Adjust offset of rear view camera” mode of Confirma-
tion / Adjustment mode.
3.
Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line of the rear of the
vehicle.
4.
Make fine adjustment to the correction line of the rear of the
vehicle with up/down/left/right switches so that its position is
aligned with the guiding line. Press “OK” switch and record the
adjusted guiding line position to the camera control unit.
CAUTION:
Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the
following service to adjust the index again.
• Remove battery for five min. Then reconnect battery.
• Remove camera control unit connector for five min. Then reconnect camera control unit connec-
tor.
SKIB3691E
Selected pattern
: 7
Up/Down adjustment range
:
−
20 – 20
Left/Right adjustment range
:
−
20 – 20
SKIB3689E
Revision: 2008 October
2009 Murano
AV
STEERING ANGLE SENSOR
AV-785
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING ANGLE SENSOR
Exploded View
INFOID:0000000003356741
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003356742
REMOVAL
1.
Remove spiral cable.
2.
Remove steering angle sensor from spiral cable.
INSTALLATION
Install in the reverse order of removal.
JSNIA0135ZZ
1.
Spiral cable
2.
Steering angle sensor
Revision: 2008 October
2009 Murano
AV-786
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
ROOF ANTENNA
ROOF ANTENNA
Exploded View
INFOID:0000000003356716
for symbols in the figure.
Removal and Installation
INFOID:0000000003356717
REMOVAL
1.
Remove headlining assembly (rear) to secure work space between vehicle and headlining. Refer to
25, "NORMAL ROOF : Exploded View"
[without sunroof] or
INT-29, "SUNROOF : Exploded View"
sunroof].
2.
Disconnect AM/FM main connector and satellite radio antenna connector.
3.
Remove antenna base & satellite radio nut, and then remove antenna base &satellite radio antenna from
roof panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When Antenna base & satellite radio antenna mounting nut tightening torque is loose, be careful
about tightening torque. Antenna sensitivity becomes poor, and when it is excessive, roof panel may
become deformed.
JPNIA0786ZZ
1.
Rod antenna
2.
Antenna bade & satellite radio an-
tenna
Antenna base & satellite ra-
dio antenna mounting nut
: 6.5 N·m (0.66 kg-m, 58 in-lb)
Revision: 2008 October
2009 Murano
AV
ANTENNA FEEDER (RADIO)
AV-787
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ANTENNA FEEDER (RADIO)
Harness Layout
INFOID:0000000003356744
JPNIA0803GB
Revision: 2008 October
2009 Murano
AV-788
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
ANTENNA FEEDER (SATELLITE RADIO)
ANTENNA FEEDER (SATELLITE RADIO)
Harness Layout
INFOID:0000000003507978
JPNIA0803GB
Revision: 2008 October
2009 Murano
AV
ANTENNA FEEDER (GPS)
AV-789
< ON-VEHICLE REPAIR >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ANTENNA FEEDER (GPS)
Harness Layout
INFOID:0000000003507979
JPNIA0803GB
Revision: 2008 October
2009 Murano
BCS
BCS-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
BCS
A
O
P
N
CONTENTS
BODY CONTROL SYSTEM
BASIC INSPECTION . . . . . . . . .
INSPECTION AND ADJUSTMENT . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) . . . . . . . . . . . ...
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT (BCM) : Description . . . . . ...
CONFIGURATION (BCM) . . . . . . . . . . ...
CONFIGURATION (BCM) : Description . . . . ....
CONFIGURATION (BCM) : Special Repair Re-
quirement . . . . . . . . . . . . . . . . ..
CONFIGURATION (BCM) : Configuration list . . ...
FUNCTION DIAGNOSIS . . . . . . . ...
BODY CONTROL SYSTEM . . . . . . . .
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
COMBINATION SWITCH READING SYSTEM
. .
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ..
SIGNAL BUFFER SYSTEM . . . . . . . ...
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
POWER CONSUMPTION CONTROL SYS-
TEM . . . . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
DOOR LOCK . . . . . . . . . . . . . . . ..
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) . . . . . . . . . . . . . . ..
REAR WINDOW DEFOGGER . . . . . . . . ...
REAR WINDOW DEFOGGER : CONSULT-III
Function (BCM - REAR DEFOGGER) . . . . . .
BUZZER . . . . . . . . . . . . . . . . . .
BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) . . . . . . . . . . . . . . . . . . ..
INT LAMP . . . . . . . . . . . . . . . . ...
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . ..
MULTI REMOTE ENT . . . . . . . . . . . .
MULTI REMOTE ENT : CONSULT-III Function
(BCM - MULTI REMOTE ENT) . . . . . . . .
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) . . . . . . . . . . . . . . ...
WIPER . . . . . . . . . . . . . . . . . .
WIPER : CONSULT-III Function (BCM - WIPER) .
FLASHER . . . . . . . . . . . . . . . . ...
FLASHER : CONSULT-III Function (BCM -
FLASHER) . . . . . . . . . . . . . . . ...
INTELLIGENT KEY . . . . . . . . . . . . .
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) . . . . . . . . .
COMB SW . . . . . . . . . . . . . . . . ..
COMB SW : CONSULT-III Function (BCM -
COMB SW) . . . . . . . . . . . . . . . ..
BCM . . . . . . . . . . . . . . . . . . ...
BCM : CONSULT-III Function (BCM - BCM) . . ...
Revision: 2008 October
2009 Murano
BCS-2
IMMU . . . . . . . . . . . . . . . . . . .
IMMU : CONSULT-III Function (BCM - IMMU) . ...
BATTERY SAVER . . . . . . . . . . . . ....
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) . . . . . . . . . . . ..
TRUNK . . . . . . . . . . . . . . . . . ..
TRUNK : CONSULT-III Function (BCM - TRUNK) ...
THEFT ALM . . . . . . . . . . . . . . . ..
THEFT ALM : CONSULT-III Function (BCM -
THEFT) . . . . . . . . . . . . . . . . ...
RETAINED PWR . . . . . . . . . . . . . ...
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) . . . . . . . . . . . . ...
SIGNAL BUFFER . . . . . . . . . . . . . ..
SIGNAL BUFFER : CONSULT-III Function (BCM
- SIGNAL BUFFER) . . . . . . . . . . . ....
AIR PRESSURE MONITOR . . . . . . . . . ..
AIR PRESSURE MONITOR : Diagnosis Descrip-
tion . . . . . . . . . . . . . . . . . . ..
AIR PRESSURE MONITOR : CONSULT-III Func-
tion (BCM - AIR PRESSURE MONITOR) . . . ...
COMPONENT DIAGNOSIS . . . . . .
U1000 CAN COMM CIRCUIT . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
U1010 CONTROL UNIT (CAN) . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
U0415 VEHICLE SPEED SIG . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B2562 LOW VOLTAGE . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ...
COMBINATION SWITCH INPUT CIRCUIT . ...
Diagnosis Procedure . . . . . . . . . . . ...
COMBINATION SWITCH OUTPUT CIRCUIT ...
Diagnosis Procedure . . . . . . . . . . . ...
ECU DIAGNOSIS . . . . . . . . . ...
BCM (BODY CONTROL MODULE) . . . . ..
Reference Value . . . . . . . . . . . . . .
Wiring Diagram - BCM - . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . .
COMBINATION SWITCH SYSTEM SYMP-
TOMS . . . . . . . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . . .
ON-VEHICLE REPAIR . . . . . . . ...
BCM (BODY CONTROL MODULE) . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COMBINATION SWITCH . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2008 October
2009 Murano
BCS
INSPECTION AND ADJUSTMENT
BCS-3
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000003486680
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before
replacement.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.
- Complete the procedure of “WRITE CONFIGURATION” in order.
- If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• When replacing BCM, perform the system initialization (NATS).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair
Requirement
INFOID:0000000003486681
1.
SAVING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to
BCS-4, "CONFIGURATION (BCM) : Special Repair Requirement"
>> GO TO 4.
4.
INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
>> WORK END
CONFIGURATION (BCM)
CONFIGURATION (BCM) : Description
INFOID:0000000003486682
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM.
Revision: 2008 October
2009 Murano
BCS-4
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
Configuration has three functions as follows
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
CAUTION:
• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
CONFIGURATION (BCM) : Special Repair Requirement
INFOID:0000000003486683
1.
WRITING MODE SELECTION
CONSULT-III Configuration
Select “CONFIGURATION” of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
CONSULT-III Configuration
Perform “WRITE CONFIGURATION - Config file”.
>> WORK END
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
CONSULT-III Configuration
1.
Select “WRITE CONFIGURATION - Manual selection”.
2.
Identify the correct model and configuration list. Refer to
BCS-5, "CONFIGURATION (BCM) : Configura-
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnor-
mal control of ECU.
4.
Select “SETTING”.
CAUTION:
Make sure to select “SETTING” even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model can not be memorized.
5.
When “COMMAND FINISHED”, select “END”.
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Function
Description
READ CONFIGURATION
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection
Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file
Writes the vehicle configuration with saved data.
Revision: 2008 October
2009 Murano
BCS
INSPECTION AND ADJUSTMENT
BCS-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIGURATION (BCM) : Configuration list
INFOID:0000000003486684
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
EXCEPT FOR MEXICO
⇔
: Items which confirm vehicle specifications
FOR MEXICO
MANUAL SETTING ITEM
NOTE
Items
Setting value
AUTO LIGHT
WITH
⇔
WITHOUT
—
DTRL
WITH
⇔
WITHOUT
• WITH: With daytime running light system
• WITHOUT: Without daytime running light system
AV C/U
WITH
⇔
WITHOUT
—
AUTO BACK DOOR
WITH
⇔
WITHOUT
—
THEFT ALM AREA
WITHOUT
⇔
MODE2
• WITHOUT: Without vehicle security system
• MODE2: With vehicle security system
I-KEY
WITH
⇔
WITHOUT
—
RAIN SENSOR
WITH
⇔
WITHOUT
—
Key Fob Type
MODE7
⇔
MODE9
• MODE7: With automatic back door system
• MODE9: Without automatic back door system
AUTO SETTING ITEM
NOTE
Items
Setting value
H/L BULB
DEFAULT
—
FR FOG LAMP
WITH
—
RR FOG LAMP
WITH
Even on a vehicle without rear fog lamp. It displays “WITH”.
TRANSMISSION
AT with ABS
—
TPMS WITH
—
TIRE PRESSURE
230kPa
—
TR OPEN SW (INT)
MODE1
—
FOG LAMP BULB
SINGLE BULB
—
DI LMP VARIAT
MODE2
—
LIGHT RECOG
MODE4
RR WIPER GND
MODE1
—
HAZARD SW TYPE
MODE1
—
BCM AC CONTROL
MODE1
—
Trunk/Glass Hatch select
Glass Hatch
Even on a vehicle without glass hatch. It displays “Glass
Hatch”.
WELCOME LIGHT SELECT
WITHOUT
—
WELCOME LIGHT TIMER
MODE1
—
REAR WIPER
WITH
—
TRUNK ACT OUTPUT
MODE2
—
RAIN SEN TYPE
MODE2
—
DROP WIP FUNCTION
WITHOUT
—
WELCOME LIGHT TIMER2
MODE1
—
Revision: 2008 October
2009 Murano
BCS-6
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
⇔
: Items which confirm vehicle specifications
MANUAL SETTING ITEM
NOTE
Items
Setting value
AUTO LIGHT
WITH
⇔
WITHOUT
—
DTRL
WITHOUT
—
AV C/U
WITH
⇔
WITHOUT
—
AUTO BACK DOOR
WITH
⇔
WITHOUT
—
THEFT ALM AREA
WITHOUT
⇔
MODE2
• WITHOUT: Without vehicle security system
• MODE2: With vehicle security system
HAZARD SW TYPE
MODE1
—
I-KEY
WITH
⇔
WITHOUT
—
RAIN SENSOR
WITH
⇔
WITHOUT
—
Key Fob Type
MODE7
⇔
MODE9
• MODE7: With automatic back door system
• MODE9: Without automatic back door system
AUTO SETTING ITEM
NOTE
Items
Setting value
H/L BULB
DEFAULT
—
FR FOG LAMP
WITH
—
RR FOG LAMP
WITH
Even on a vehicle without rear fog lamp. It displays “WITH”.
TRANSMISSION
AT with ABS
—
TPMS WITHOUT
—
TR OPEN SW (INT)
MODE1
—
FOG LAMP BULB
SINGLE BULB
—
DI LMP VARIAT
MODE2
—
LIGHT RECOG
MODE4
RR WIPER GND
MODE1
—
BCM AC CONTROL
MODE1
—
Trunk/Glass Hatch select
Glass Hatch
Even on a vehicle without glass hatch. It displays “Glass
Hatch”.
WELCOME LIGHT SELECT
WITHOUT
—
WELCOME LIGHT TIMER
MODE1
—
REAR WIPER
WITH
—
TRUNK ACT OUTPUT
MODE2
—
RAIN SEN TYPE
MODE2
—
DROP WIP FUNCTION
WITHOUT
—
WELCOME LIGHT TIMER2
MODE1
—
Revision: 2008 October
2009 Murano
BCS
BODY CONTROL SYSTEM
BCS-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FUNCTION DIAGNOSIS
BODY CONTROL SYSTEM
System Description
INFOID:0000000003441350
OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con-
trol function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings.
BCM CONTROL FUNCTION LIST
System
Reference
Combination switch reading system
Signal buffer system
Power consumption control system
Auto light system
Turn signal and hazard warning lamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Headlamp system
•
•
(Halogen type headlamp)
Parking, license plate and tail lamps system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Front fog lamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Exterior lamp battery saver system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Daytime running light system
•
•
(Halogen type headlamp)
Interior room lamp control system
Step lamp system
Interior room lamp battery saver system
Front wiper and washer system
•
WW-5, "WITH RAIN SENSOR : System Diagram"
(With rain
sensor)
•
WW-9, "WITHOUT RAIN SENSOR : System Diagram"
(With-
out rain sensor)
Rear wiper and washer system
Warning chime system
WCS-5, "WARNING CHIME SYSTEM : System Diagram"
Door lock system
•
(With Intelligent Key system)
•
(Without Intelligent Key system)
Back door opener system (Without Intelligent Key system)
Automatic back door system
Automatic drive positioner system
ADP-13, "AUTOMATIC DRIVE POSITIONER SYSTEM : System
Diagram"
Nissan Vehicle Immobilizer System (NVIS) - NATS (With Intelligent
Key system)
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст