Nissan Murano Z51 (2008 year). Manual — part 293
PWC-20
< COMPONENT DIAGNOSIS >
POWER WINDOW MOTOR
3.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE)
Check front power window motor (driver side).
Refer to
PWC-20, "DRIVER SIDE : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power window motor (driver side). Refer to
GW-20, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
DRIVER SIDE : Component Inspection
INFOID:0000000004756740
1.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (driver side) connector.
3.
Check motor operate by connecting the battery voltage directly to front power window motor (driver side)
terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front power window motor (driver side). Refer to
GW-20, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000004756741
Door glass moves UP/DOWN by receiving the signal from power window main switch or front power window
switch (passenger side).
PASSENGER SIDE : Component Function Check
INFOID:0000000004756742
1.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) OPERATION
Check front power window motor (passenger side) operation with power window main switch or front power
window switch (passenger side).
Is the inspection result normal?
YES
>> Power window motor (passenger side) is OK.
NO
>> Refer to
PWC-20, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000004756743
1.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window motor (passenger side) harness connector and ground.
Front power window motor (driver side)
Motor condition
Connector
Terminal
(+)
(–)
D7
1
2
DOWN
2
1
UP
Revision: 2008 October
2009 Murano
POWER WINDOW MOTOR
PWC-21
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check continuity between front power window switch (passenger side) harness connector and front power
window motor (passenger side) harness connector.
4.
Check continuity between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side).
PWC-114, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE)
Check front power window motor (passenger side).
Refer to
PWC-21, "PASSENGER SIDE : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace front power window motor (passenger side). Refer to
GW-20, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
PASSENGER SIDE : Component Inspection
INFOID:0000000004756744
1.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (passenger side) connector.
3.
Check motor operate by connecting the battery voltage directly to front power window motor (passenger
side) terminals.
(+)
(–)
Condition
Voltage (V)
(Approx.)
Front power window motor (passenger side)
Connector
Terminal
D46
1
Ground
Front power win-
dow switch
(passenger side)
UP
Battery voltage
DOWN
0
2
UP
0
DOWN
Battery voltage
Front power window switch (passenger side)
Front power window motor (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D45
9
D46
1
Existed
8
2
Front power window switch (passenger side)
Ground
Continuity
Connector
Terminal
D45
9
Not existed
8
Revision: 2008 October
2009 Murano
PWC-22
< COMPONENT DIAGNOSIS >
POWER WINDOW MOTOR
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front power window motor (passenger side). Refer to
GW-20, "Removal and Installation"
.
REAR LH
REAR LH : Description
INFOID:0000000004756745
Door glass moves UP/DOWN by receiving the signal from power window main switch or rear power window
switch LH.
REAR LH : Component Function Check
INFOID:0000000004756746
1.
CHECK REAR POWER WINDOW MOTOR LH OPERATION
Check rear power window motor LH operation with power window main switch or rear power window switch
LH.
Is the inspection result normal?
YES
>> Rear power window motor LH is OK.
NO
>> Refer to
PWC-22, "REAR LH : Diagnosis Procedure"
REAR LH : Diagnosis Procedure
INFOID:0000000004756747
1.
CHECK REAR POWER WINDOW MOTOR LH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear power window motor LH connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW MOTOR LH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch LH connector.
3.
Check continuity between rear power window switch LH harness connector and rear power window motor
LH harness connector.
Front power window motor (passenger side)
Motor condition
Connector
Terminal
(+)
(–)
D46
2
1
DOWN
1
2
UP
(+)
(–)
Condition
Voltage (V)
(Approx.)
Rear power window motor LH
Connector
Terminal
D82
1
Ground
Rear power win-
dow switch LH
UP
Battery voltage
DOWN
0
3
UP
0
DOWN
Battery voltage
Rear power window switch LH
Rear power window motor LH
Continuity
Connector
Terminal
Connector
Terminal
D83
4
D82
3
Existed
5
1
Revision: 2008 October
2009 Murano
POWER WINDOW MOTOR
PWC-23
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
4.
Check continuity between rear power window switch LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window switch LH.Refer to
PWC-114, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK REAR POWER WINDOW MOTOR LH
Check rear power window motor LH.
Refer to
PWC-23, "REAR LH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace rear power window motor LH. Refer to
GW-25, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
REAR LH : Component Inspection
INFOID:0000000004756748
COMPONENT INSPECTION
1.
CHECK REAR POWER WINDOW MOTOR LH
1.
Turn ignition switch OFF.
2.
Disconnect rear power window motor LH connector.
3.
Check motor operate by connecting the battery voltage directly to rear power window motor LH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace rear power window motor LH. Refer to
GW-25, "Removal and Installation"
REAR RH
REAR RH : Description
INFOID:0000000004756749
Door glass moves UP/DOWN by receiving the signal from power window main switch or rear power window
switch RH.
REAR RH : Component Function Check
INFOID:0000000004756750
1.
CHECK REAR POWER WINDOW MOTOR RH OPERATION
Check rear power window motor RH operation with power window main switch or rear power window switch
RH.
Is the inspection result normal?
YES
>> Rear power window motor RH is OK.
NO
>> Refer to
PWC-24, "REAR RH : Diagnosis Procedure"
.
Rear power window switch LH
Ground
Continuity
Connector
Terminal
D83
4
Not existed
5
Rear power window motor LH
Motor condition
Connector
Terminal
(+)
(–)
D82
3
1
DOWN
1
3
UP
Revision: 2008 October
2009 Murano
PWC-24
< COMPONENT DIAGNOSIS >
POWER WINDOW MOTOR
REAR RH : Diagnosis Procedure
INFOID:0000000004756751
1.
CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear power window motor RH connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW MOTOR RH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch RH connector.
3.
Check continuity between rear power window switch RH harness connector and rear power window motor
RH harness connector.
4.
Check continuity between rear power window switch RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window switch RH.Refer to
PWC-114, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK REAR POWER WINDOW MOTOR RH
Check rear power window motor RH.
Refer to
PWC-25, "REAR RH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace rear power window motor RH. Refer to
GW-25, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
(+)
(–)
Condition
Voltage (V)
(Approx.)
Rear power window motor RH
Connector
Terminal
D102
1
Ground
Rear power win-
dow switch RH
UP
Battery voltage
DOWN
0
3
UP
0
DOWN
Battery voltage
Rear power window switch RH
Rear power window motor RH
Continuity
Connector
Terminal
Connector
Terminal
D103
4
D102
3
Existed
5
1
Rear power window switch RH
Ground
Continuity
Connector
Terminal
D103
4
Not existed
5
Revision: 2008 October
2009 Murano
POWER WINDOW MOTOR
PWC-25
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR RH : Component Inspection
INFOID:0000000004756752
COMPONENT INSPECTION
1.
CHECK REAR POWER WINDOW MOTOR RH
1.
Turn ignition switch OFF.
2.
Disconnect rear power window motor RH connector.
3.
Check motor operation by connecting the battery voltage directly to rear power window motor RH termi-
nals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace rear power window motor RH. Refer to
GW-25, "Removal and Installation"
.
Rear power window motor RH
Motor condition
Connector
Terminal
(+)
(–)
D102
3
1
DOWN
1
3
UP
Revision: 2008 October
2009 Murano
PWC-26
< COMPONENT DIAGNOSIS >
ENCODER CIRCUIT
ENCODER CIRCUIT
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000004756753
Detects condition of the front power window motor (driver side) operation and transmits to power window main
switch as the pulse signal.
DRIVER SIDE : Component Function Check
INFOID:0000000004756754
1.
CHECK ENCODER OPERATION
Check driver side door glass perform AUTO open/close operation normally by power window main switch.
Is the inspection result normal?
YES
>> Encoder is OK.
NO
>> Refer to
PWC-26, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000004756755
1.
CHECK ENCODER SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between power window main switch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-114, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK ENCORDER SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and front power window motor (driver side) connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
(+)
(–)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D5
9
Ground
Refer to following signal
13
JMKIA2682GB
Power window main switch
Front power window motor
(driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
9
D7
3
Existed
13
5
Revision: 2008 October
2009 Murano
ENCODER CIRCUIT
PWC-27
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK ENCORDER POWER SUPPLY
1.
Connect power window main switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK ENCORDER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-114, "Removal and Installation"
.
NO
>> Repair or replace harness.
5.
CHECK GROUND CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK GROUND CIRCUIT 2
Power window main switch
Ground
Continuity
Connector
Terminal
D5
9
Not existed
13
(+)
(–)
Voltage (V)
(Approx.)
Front power window motor (driver side)
Connector
Terminal
D7
4
Ground
Battery voltage
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
15
D7
4
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D5
15
Not existed
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
2
D7
6
Existed
Revision: 2008 October
2009 Murano
PWC-28
< COMPONENT DIAGNOSIS >
ENCODER CIRCUIT
1.
Connect power window main switch connector.
2.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (driver side). Refer to
GW-20, "Removal and Installation"
NO
>> Replace power window main switch. Refer to
PWC-114, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000004756756
Detects condition of the front power window motor (passenger side) operation and transmits to front power
window switch (passenger side) as the pulse signal.
PASSENGER SIDE : Component Function Check
INFOID:0000000004756757
1.
CHECK ENCODER OPERATION
Check passenger side door glass perform AUTO open/close operation normally by power window main switch
or front power window switch (passenger side).
Is the inspection result normal?
YES
>> Encoder is OK.
NO
>> Refer to
PWC-28, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000004756758
1.
CHECK ENCODER SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between front power window switch (passenger side) harness connector and ground using
oscilloscope.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-114, "Removal and Installa-
.
NO
>> GO TO 2.
2.
CHECK ENCORDER SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
Power window main switch
Ground
Continuity
Connector
Terminal
D5
2
Existed
(+)
(–)
Signal
(Reference value)
Front power window switch (passenger side)
Connector
Terminal
D45
12
Ground
Refer to following signal
15
JMKIA2927GB
Revision: 2008 October
2009 Murano
ENCODER CIRCUIT
PWC-29
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
2.
Disconnect front power window switch (passenger side) connector and front power window motor (pas-
senger side) connector.
3.
Check continuity between front power window switch (passenger side) harness connector and front power
window motor (passenger side) harness connector.
4.
Check continuity between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK ENCORDER POWER SUPPLY
1.
Connect front power window switch (passenger side) connector.
2.
Turn ignition switch ON.
3.
Check voltage between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK ENCODER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check continuity between front power window switch (passenger side) harness connector and front power
window motor (passenger side) harness connector.
4.
Check continuity between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-114, "Removal and Installa-
.
NO
>> Repair or replace harness.
5.
CHECK GROUND CIRCUIT 1
1.
Turn ignition switch OFF.
Front power window switch (passenger side)
Front power window motor (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D45
12
D46
5
Existed
15
3
Front power window switch (passenger side)
Ground
Continuity
Connector
Terminal
D45
12
Not existed
15
(+)
(–)
Voltage (V)
(Approx.)
Front power window motor (passenger side)
Connector
Terminal
D46
4
Ground
Battery voltage
Front power window switch (passenger side)
Front power window motor (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D45
4
D46
4
Existed
Front power window switch (passenger side)
Ground
Continuity
Connector
Terminal
D45
4
Not existed
Revision: 2008 October
2009 Murano
PWC-30
< COMPONENT DIAGNOSIS >
ENCODER CIRCUIT
2.
Disconnect front power window switch (passenger side) connector.
3.
Check continuity between front power window switch (passenger side) harness connector and front power
window motor (passenger side) harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK GROUND CIRCUIT 2
1.
Connect front power window switch (passenger side) connector.
2.
Check continuity between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (passenger side). Refer to
GW-20, "Removal and Installation"
.
NO
>> Replace front power window switch (passenger side). Refer to
PWC-114, "Removal and Installa-
.
Front power window switch (passenger side)
Front power window motor (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D45
3
D46
6
Existed
Front power window switch (passenger side)
Ground
Continuity
Connector
Terminal
D45
3
Existed
Revision: 2008 October
2009 Murano
POWER WINDOW SERIAL LINK
PWC-31
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW SERIAL LINK
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Description
INFOID:0000000004756759
Power window main switch, front power window switch (passenger side) and BCM transmit and receive the
signal by power window serial link.
The signal mentioned below is transmitted from BCM to power window main switch, front power window
switch (passenger side).
• Keyless power window down signal
The signal mentioned below is transmitted from power window main switch to front power window switch (pas-
senger side).
• Front passenger side door window operation signal
• Power window control by key cylinder switch signal
• Power window lock switch signal
• Retained power operation signal
POWER WINDOW MAIN SWITCH : Component Function Check
INFOID:0000000004756760
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
With CONSULT-III
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT-III. Refer to
DLK-59, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES
>> Power window serial link is OK.
NO
>> Refer to
PWC-31, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
POWER WINDOW MAIN SWITCH : Diagnosis Procedure
INFOID:0000000004756761
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SERIAL LINK SIGNAL
Monitor item
Condition
CDL LOCK SW
LOCK
: ON
UNLOCK
: OFF
CDL UNLOCK SW
LOCK
: OFF
UNLOCK
: ON
(+)
(–)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D5
14
Ground
JPMIA0013GB
Revision: 2008 October
2009 Murano
PWC-32
< COMPONENT DIAGNOSIS >
POWER WINDOW SERIAL LINK
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between power window main switch harness connector and ground.
Is the measurement value within the specification?
YES
>> Replace power window main switch. Refer to
PWC-114, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK POWER WINDOW SERIAL LINK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM connector and power window main switch connector.
4.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Description
INFOID:0000000004756762
Power window main switch, front power window switch (passenger side) and BCM transmit and receive the
signal by power window serial link.
The signal mentioned below is transmitted from BCM to power window main switch, front power window
switch (passenger side).
• Keyless power window down signal
The signal mentioned below is transmitted from power window main switch to front power window switch (pas-
senger side).
• Front passenger side door window operation signal
• Power window control by key cylinder switch signal
• Power window lock switch signal
• Retained power operation signal
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Component Function
Check
INFOID:0000000004756763
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
(+)
(–)
Voltage (V)
(Approx.)
Power window main switch
Connector
Terminal
D5
14
Ground
Battery voltage
BCM
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
M123
132
D5
14
Existed
BCM
Ground
Continuity
Connector
Terminal
M123
132
Not existed
Revision: 2008 October
2009 Murano
POWER WINDOW SERIAL LINK
PWC-33
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
With CONSULT-III
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT-III. Refer to
DLK-59, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES
>> Power window serial link is OK.
NO
>> Refer to
PWC-33, "FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Proce-
.
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure
INFOID:0000000004756764
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-114, "Removal and Installa-
.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SERIAL LINK SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-114, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK POWER WINDOW SERIAL LINK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM connector and front power window switch (passenger side) connector.
Monitor item
Condition
CDL LOCK SW
LOCK
: ON
UNLOCK
: OFF
CDL UNLOCK SW
LOCK
: OFF
UNLOCK
: ON
(+)
(
−
)
Signal
(Reference value)
Front power window switch (passenger side)
Connector
Terminal
D45
16
Ground
JPMIA0013GB
(+)
(–)
Voltage (V)
(Approx.)
Front power window switch (passenger side)
Connector
Terminal
D45
16
Ground
Battery voltage
Revision: 2008 October
2009 Murano
PWC-34
< COMPONENT DIAGNOSIS >
POWER WINDOW SERIAL LINK
4.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
NO
>> Repair or replace harness.
BCM
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M123
132
D45
16
Existed
BCM
Ground
Continuity
Connector
Terminal
M123
132
Not existed
Revision: 2008 October
2009 Murano
BCM (BODY CONTROL MODULE)
PWC-35
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value
INFOID:0000000004756221
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III MONITOR ITEM
Monitor Item
Condition
Value/Status
FR WIPER HI
Other than front wiper switch HI
Off
Front wiper switch HI
On
FR WIPER LOW
Other than front wiper switch LO
Off
Front wiper switch LO
On
FR WASHER SW
Front washer switch OFF
Off
Front washer switch ON
On
FR WIPER INT
Other than front wiper switch INT/AUTO
Off
Front wiper switch INT/AUTO
On
FR WIPER STOP
Front wiper is not in STOP position
Off
Front wiper is in STOP position
On
INT VOLUME
Wiper intermittent dial is in a dial position 1 - 7
Wiper intermittent dial position
RR WIPER ON
Other than rear wiper switch ON
Off
Rear wiper switch ON
On
RR WIPER INT
Other than rear wiper switch INT
Off
Rear wiper switch INT
On
RR WASHER SW
Rear washer switch OFF
Off
Rear washer switch ON
On
RR WIPER STOP
Rear wiper is in STOP position
Off
Rear wiper is not in STOP position
On
TURN SIGNAL R
Other than turn signal switch RH
Off
Turn signal switch RH
On
TURN SIGNAL L
Other than turn signal switch LH
Off
Turn signal switch LH
On
TAIL LAMP SW
Other than lighting switch 1ST and 2ND
Off
Lighting switch 1ST or 2ND
On
HI BEAM SW
Other than lighting switch HI
Off
Lighting switch HI
On
HEAD LAMP SW 1
Other than lighting switch 2ND
Off
Lighting switch 2ND
On
HEAD LAMP SW 2
Other than lighting switch 2ND
Off
Lighting switch 2ND
On
PASSING SW
Other than lighting switch PASS
Off
Lighting switch PASS
On
AUTO LIGHT SW
Other than lighting switch AUTO
Off
Lighting switch AUTO
On
FR FOG SW
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст