Nissan Murano Z51 (2008 year). Manual — part 262
MIR-8
< FUNCTION DIAGNOSIS >
[WITH ADP]
DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)
MIR CHNG SW–R
“ON/OFF”
×
×
ON/OFF status judged from the door mirror remote control
switch (switching to right) signal.
MIR CHNG SW–L
“ON/OFF”
×
×
ON/OFF status judged from the door mirror remote control
switch (switching to left) signal.
TILT SW-UP
“ON/OFF”
×
×
ON/OFF status judged from the tilt switch (up) signal.
TILT SW-DOWN
“ON/OFF”
×
×
ON/OFF status judged from the tilt switch (down) signal.
TELESCO SW-FR
“ON/OFF”
×
×
ON/OFF status judged from the telescoping switch (for-
ward) signal.
TELESCO SW-RR
“ON/OFF”
×
×
ON/OFF status judged from the telescoping switch (back-
ward) signal.
DETENT SW
“ON/OFF”
×
×
The selector lever position “OFF (P position) / ON (other
than P position)” judged from the detention switch signal.
STARTER SW
“ON/OFF”
×
×
Ignition key switch ON (START, ON) /OFF (ACC, OFF) sta-
tus judged from the ignition switch signal.
SLIDE PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
RECLN PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
LIFT FR PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
LIFT RR PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
MIR/SEN RH U–D
“V”
–
×
Voltage input from door mirror sensor (passenger side) up/
down is displayed.
MIR/SEN RH R–L
“V”
–
×
Voltage input from door mirror sensor (passenger side) left/
right is displayed.
MIR/SEN LH U–D
“V”
–
×
Voltage input from door mirror sensor (driver side) up/down
is displayed.
MIR/SEN LH R–L
“V”
–
×
Voltage input from door mirror sensor (driver side) left/right
is displayed.
TILT PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.
TELESCO PULSE
—
–
×
Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases.
VEHICLE SPEED
—
×
×
Display the vehicle speed signal received from combination
meter by numerical value [km/h].
P RANG SW CAN
“ON/OFF”
×
×
ON/OFF status judged from the P range switch signal.
R RANGE (CAN)
“ON/OFF”
×
×
ON/OFF status judged from the R range switch signal.
DOOR SW–FL
“ON/OFF”
×
×
ON/OFF status judged from the door switch (front driver
side) signal.
DOOR SW–FR
“ON/OFF”
×
×
ON/OFF status judged from the door switch (front passen-
ger side) signal.
IGN ON SW
“ON/OFF”
×
×
ON/OFF status judged from the ignition switch signal.
ACC ON SW
“ON/OFF”
×
×
ON/OFF status judged from the ACC switch signal.
KEY ON SW
“ON/OFF”
×
×
ON/OFF status judged from the key on switch signal.
Monitor Item
Unit
Main
Signals
Selection
From
Menu
Contents
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)
MIR-9
< FUNCTION DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
ACTIVE TEST
CAUTION:
When driving vehicle, do not perform active test.
WORK SUPPORT
KEYLESS ID
—
×
×
Key ID status judged from the key ID signal.
KYLS DR UNLK
“ON/OFF”
×
×
ON/OFF status judged from the driver side door unlock ac-
tuator output switch signal.
VHCL SPEED (ABS)
“ON/OFF”
×
×
ON/OFF status judged from vehicle speed signal.
HANDLE
“RHD/LHD”
×
×
RHD/LHD status judged from handle position signal.
TRANSMISSION
“AT or CVT/
MT”
×
×
AT or CVT/MT status judged from transmission.
STEERING STATUS
“LOCK/UN-
LOCK”
×
×
LOCK/UNLOCK status judged from steering lock unit.
Monitor Item
Unit
Main
Signals
Selection
From
Menu
Contents
Test item
Description
SEAT SLIDE
Activates/deactivates the sliding motor.
SEAT RECLINING
Activates/deactivates the reclining motor.
SEAT LIFTER FR
Activates/deactivates the lifting motor (front).
SEAT LIFTER RR
Activates/deactivates the lifting motor (rear).
TILT MOTOR
Activates/deactivates the tilt motor.
TELESCO MOTOR
Activates/deactivates the telescopic motor.
MIRROR MOTOR RH
Activates/deactivates the mirror motor (passenger side).
MIRROR MOTOR LH
Activates/deactivates the mirror motor (driver side).
MEMORY SW INDCTR
Turns ON/OFF the memory indicator.
Work item
Content
Item
SEAT SLIDE VOLUME SET
The amount of seat sliding for entry/exit assist can be selected
from 3 items.
40 mm
80 mm
150 mm
EXIT TILT SETTING
Entry/exit assist (steering column) can be selected:
ON (operated) – OFF (not operated)
ON
OFF
EXIT SEAT SLIDE SETTING
Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)
ON
OFF
Revision: 2008 October
2009 Murano
MIR-10
< COMPONENT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
COMPONENT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH
MIRROR SWITCH
MIRROR SWITCH : Description
INFOID:0000000003554741
It operates angle of the door mirror face.
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSITIONER CONTROL UNIT.
MIRROR SWITCH : Component Function Check
INFOID:0000000003554742
1.
CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.
Is the inspection result normal?
YES
>> Mirror switch function is OK.
NO
>> Refer to
MIR-10, "MIRROR SWITCH : Diagnosis Procedure"
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000003554743
1.
CHECK MIRROR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK MIRROR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
Monitor item
Condition
MIR CON SW-UP/DN
When operating the mirror switch toward the up or down side.
: ON
Other than above.
: OFF
MIR CON SW-RH/LH
When operating the mirror switch toward the right or left side.
: ON
Other than above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D14
4
Ground
5
12
13
15
Revision: 2008 October
2009 Murano
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-11
< COMPONENT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-205, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK MIRROR SWITCH
Check door mirror remote control switch (mirror switch).
Refer to
MIR-11, "MIRROR SWITCH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (mirror switch). Refer to
.
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-40, "Intermittent Incident"
.
>> INSPECTION END
MIRROR SWITCH : Component Inspection
INFOID:0000000003554744
1.
CHECK MIRROR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Automatic drive positioner control unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
3
D14
15
Existed
4
13
15
12
16
4
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
3
Not existed
4
15
16
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
Revision: 2008 October
2009 Murano
MIR-12
< COMPONENT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-66, "Removal and Installation"
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000003554745
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000003554746
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Is the inspection result normal?
YES
>> Changeover switch function is OK.
NO
>> Refer to
MIR-12, "CHANGEOVER SWITCH : Diagnosis Procedure"
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000003554747
1.
CHECK CHANGEOVER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK CHANGEOVER SWITCH CIRCUIT
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
4
7
Mirror switch
RIGHT
Existed
Other than above
Not existed
13
LEFT
Existed
Other than above
Not existed
15
UP
Existed
Other than above
Not existed
12
DOWN
Existed
Other than above
Not existed
Monitor item
Condition
MIR CHNG SW-R/L
When operating the changeover toward the right or left side.
: ON
Other than above.
: OFF
(+)
(–)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
D14
10
Ground
5
11
Revision: 2008 October
2009 Murano
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-13
< COMPONENT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-205, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch (changeover switch).
Refer to
MIR-13, "CHANGEOVER SWITCH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (changeover switch). Refer to
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-40, "Intermittent Incident"
.
>> INSPECTION END
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000003554748
1.
CHECK CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Automatic drive positioner control unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
2
D14
11
Existed
14
10
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
2
Not existed
14
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
D14
7
Existed
Revision: 2008 October
2009 Murano
MIR-14
< COMPONENT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
MIR-66, "Removal and Installation"
Door mirror remote control switch
Condition
Continuity
Connector
Terminal
D14
10
7
Changeover switch
LEFT
Existed
Other than above
Not existed
11
RIGHT
Existed
Other than above
Not existed
Revision: 2008 October
2009 Murano
DOOR MIRROR
MIR-15
< COMPONENT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR
Wiring Diagram - DOOR MIRROR SYSTEM (WITH AUTOMATIC DRIVE POSITION-
ER) -
INFOID:0000000004786413
JCLWM2736GB
Revision: 2008 October
2009 Murano
MIR-16
< COMPONENT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR
JCLWM2737GB
Revision: 2008 October
2009 Murano
DOOR MIRROR
MIR-17
< COMPONENT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
JCLWM2738GB
Revision: 2008 October
2009 Murano
MIR-18
< COMPONENT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR
JCLWM2739GB
Revision: 2008 October
2009 Murano
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
MIR-19
< COMPONENT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
Wiring Diagram - INSIDE MIRROR SYSTEM -
INFOID:0000000003554749
JCLWM2742GB
Revision: 2008 October
2009 Murano
MIR-20
< COMPONENT DIAGNOSIS >
[WITH ADP]
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
JCLWM2743GB
Revision: 2008 October
2009 Murano
DRIVER SEAT CONTROL UNIT
MIR-21
< ECU DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
ECU DIAGNOSIS
DRIVER SEAT CONTROL UNIT
Reference Value
INFOID:0000000004786385
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III MONITOR ITEM
Monitor Item
Condition
Value/Status
SET SW
Set switch
Push
ON
Release
OFF
MEMORY SW1
Memory switch 1
Push
ON
Release
OFF
MEMORY SW2
Memory switch 2
Push
ON
Release
OFF
SLIDE SW–FR
Sliding switch (forward)
Operate
ON
Release
OFF
SLIDE SW–RR
Sliding switch (backward)
Operate
ON
Release
OFF
RECLN SW–FR
Reclining switch (forward)
Operate
ON
Release
OFF
RECLN SW–RR
Reclining switch (back-
ward)
Operate
ON
Release
OFF
LIFT FR SW–UP
Lifting switch front (up)
Operate
ON
Release
OFF
LIFT FR SW–DN
Lifting switch front (down)
Operate
ON
Release
OFF
LIFT RR SW–UP
Lifting switch rear (up)
Operate
ON
Release
OFF
LIFT RR SW–DN
Lifting switch rear (down)
Operate
ON
Release
OFF
MIR CON SW–UP
Mirror switch
Up
ON
Other than above
OFF
MIR CON SW–DN
Mirror switch
Down
ON
Other than above
OFF
MIR CON SW–RH
Mirror switch
Right
ON
Other than above
OFF
MIR CON SW–LH
Mirror switch
Left
ON
Other than above
OFF
MIR CHNG SW–R
Changeover switch
Right
ON
Other than above
OFF
MIR CHNG SW–L
Changeover switch
Left
ON
Other than above
OFF
TILT SW-UP
Tilt switch
Upward
ON
Other than above
OFF
TILT SW-DOWN
Tilt switch
Downward
ON
Other than above
OFF
Revision: 2008 October
2009 Murano
MIR-22
< ECU DIAGNOSIS >
[WITH ADP]
DRIVER SEAT CONTROL UNIT
TELESCO SW-FR
Telescopic switch
Forward
ON
Other than above
OFF
TELESCO SW-RR
Telescopic switch
Backward
ON
Other than above
OFF
DETENT SW
A/T selector lever
P position
OFF
Other than above
ON
STARTER SW
Ignition position
Cranking
ON
Other than above
OFF
SLIDE PULSE
Seat sliding
Forward
The numeral value decreases *
Backward
The numeral value increases*
Other than above
No change to numeral value*
RECLN PULSE
Seat reclining
Forward
The numeral value decreases*
Backward
The numeral value increases
*
Other than above
No change to numeral value
*
LIFT FR PULSE
Seat lifter (front)
Up
The numeral value decreases
*
Down
The numeral value increases
*
Other than above
No change to numeral value
*
LIFT RR PULSE
Seat lifter (rear)
Up
The numeral value decreases
*
Down
The numeral value increases
*
Other than above
No change to numeral value
*
MIR/SEN RH U–D
Door mirror (passenger side)
Change between 3.4 (close to peak)
0.6 (close to valley)
MIR/SEN RH R–L
Door mirror (passenger side)
Change between 3.4 (close to left edge)
0.6 (close to right edge)
MIR/SEN LH U–D
Door mirror (driver side)
Change between 3.4 (close to peak)
0.6 (close to valley)
MIR/SEN LH R–L
Door mirror (driver side)
Change between 0.6 (close to left edge)
3.4 (close to right edge)
TILT PULSE
Tilt position
Upward
The numeral value decreases
*
Downward
The numeral value increases
*
Other than above
No change to numeral value
*
TELESCO PULSE
Telescopic position
Forward
The numeral value decreases
*
Backward
The numeral value increases
*
Other than above
No change to numeral value
*
STEERING STATUS
Steering lock unit
LOCK
LOCK
unlock
UNLOCK
VEHICLE SPEED
The condition of vehicle speed is displayed
km/h
P RANG SW CAN
A/T selector lever
P position
ON
Other than above
OFF
R RANGE (CAN)
A/T selector lever
R position
ON
Other than above
OFF
DOOR SW-FL
Driver door
Open
ON
Close
OFF
Monitor Item
Condition
Value/Status
Revision: 2008 October
2009 Murano
DRIVER SEAT CONTROL UNIT
MIR-23
< ECU DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
*
: The value at the position attained when the battery is connected is regarded as 32768.
TERMINAL LAYOUT
PHYSICAL VALUES
DOOR SW-FR
Passenger door
Open
ON
Close
OFF
IGN ON SW
Ignition switch
ON position
ON
Other than above
OFF
ACC ON SW
Ignition switch
ACC or ON position
ON
Other than above
OFF
KEY ON SW
Intelligent Key
Inserted is key slot
ON
Inserted is not key slot
OFF
KEYLESS ID
UNLOCK button of Intelligent Key is pressed
1,2,3,4or5
KYLS DR UNLK
Intelligent Key or driver
side door request switch
ON
ON
OFF
OFF
VHCL SPEED (ABS)
Can signal from ABS
Received
ON
Not received
OFF
HANDLE
The BCM for handle position is displayed
LHD
RHD
TRANSMISSION
Transmission type is displayed
AT or CVT
MT
Monitor Item
Condition
Value/Status
JMJIA1689ZZ
Terminal No.
(wire color)
Description
Condition
Voltage (V)
(Approx)
+
-
Signal name
Input/
Output
1
(R)
Ground
Power source
Input
—
Battery voltage
2
(B)
Ground
Ground (power)
—
—
0
3
(G)
Ground
Sliding motor backward
output signal
Output
Seat sliding
Operate
(backward)
Battery voltage
Stop
0
4
(G/R)
Ground
Sliding motor forward out-
put signal
Output
Seat sliding
Operate
(forward)
Battery voltage
Release
0
5
(V)
Ground
Reclining motor backward
output signal
Output
Seat reclining
Operate
(backward)
Battery voltage
Stop
0
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст