Nissan Murano Z51 (2008 year). Manual — part 401
WT-10
< FUNCTION DIAGNOSIS >
TPMS
Combination meter
Transmits the vehicle speed signal via CAN communication to BCM.
Receives the following signals via CAN communication to BCM.
• Tire pressure warning lamp signal
• Hazard lamp signal
• Buzzer signal
Low tire pressure warning lamp
Illuminates if malfunction is detected in electrical system of TPMS.
Component parts
Function
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
WT-11
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000003630901
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1: At models with Intelligent Key system this item is displayed, but is not used.
• *2: At models with rain sensor this mode is displayed, but is not used.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT*
1
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
*
2
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
3
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
Revision: 2008 October
2009 Murano
WT-12
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
• *3: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : Diagnosis Description
INFOID:0000000003375944
DESCRIPTION
During driving, the TPMS receives the signal transmitted from the transmitter installed in each wheel, when
the tire pressure becomes low. The control unit (BCM) of this system has pressure judgment and trouble diag-
nosis functions.
When the TPMS detects low inflation pressure or another unusual symptom, the low tire pressure warning
lamps in the combination meter comes on.
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
WT-13
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SELF DIAGNOSTIC PROCEDURE (WITH CONSULT-III)
With CONSULT-III
Touch “SELF-DIAG RESULT” display shows malfunction experienced since the last erasing operation. Refer
to
.
SELF DIAGNOSTIC PROCEDURE (WITHOUT CONSULT-III)
Without CONSULT-III
To start the self-diagnostic results mode, ground terminal of the tire pressure warning check connector. The
malfunction location is indicated by the low tire pressure warning lamp blinking.
NOTE:
When the low tire pressure warning lamp blinks 5 Hz and continues repeating it, the system is normal.
JPEIC0030GB
Blinking
pattern
Items
Diagnostic items detected when···
Check
item
15
Tire pressure value (Front LH)
Front LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
16
Tire pressure value (Front RH)
Front RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
17
Tire pressure value (Rear RH)
Rear RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
18
Tire pressure value (Rear LH)
Rear LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
21
Transmitter no data (Front LH)
Data from front LH transmitter can not be receive.
22
Transmitter no data (Front RH)
Data from front RH transmitter can not be receive.
23
Transmitter no data (Rear RH)
Data from rear RH transmitter can not be receive.
24
Transmitter no data (Rear LH)
Data from rear LH transmitter can not be receive.
31
Transmitter checksum error
(Front LH)
Checksum data from front LH transmitter is malfunctioning.
32
Transmitter checksum error
(Front RH)
Checksum data from front RH transmitter is malfunctioning.
33
Transmitter checksum error
(Rear RH)
Checksum data from rear RH transmitter is malfunctioning.
34
Transmitter checksum error
(Rear LH)
Checksum data from rear LH transmitter is malfunctioning.
35
Transmitter pressure data error
(Front LH)
Air pressure data from front LH transmitter is malfunction.
36
Transmitter pressure data error
(Front RH)
Air pressure data from front RH transmitter is malfunction.
37
Transmitter pressure data error
(Rear RH)
Air pressure data from rear RH transmitter is malfunction.
38
Transmitter pressure data error
(Rear LH)
Air pressure data from rear LH transmitter is malfunction.
Revision: 2008 October
2009 Murano
WT-14
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
NOTE:
182.7 kPa (1.9 kg/cm
2
, 26 psi): Standard air pressure is for 230 kPa (2.3 kg/cm
2
, 33 psi) vehicles.
ERASE SELF-DIAGNOSIS
With CONSULT-III
1.
Perform applicable inspection of malfunctioning item and then repair or replace.
2.
Turn ignition switch ON and select “SELF-DIAG RESULTS” mode for “AIR PRESSURE MONITOR” with
CONSULT-III.
3.
Touch “ERASE” on CONSULT-III screen to erase memory.
Without CONSULT-III
• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned ON and OFF.
• However, this information is erased by turning ignition switch OFF after performing self-diagnostic or by
erasing the memory using the CONSULT-III.
AIR PRESSURE MONITOR : CONSULT-III Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000003375945
WORK SUPPORT MODE
ID Read
The registered ID number is displayed.
ID Regist
WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
SELF-DIAG RESULTS MODE
Operation Procedure
.
DATA MONITOR MODE
Screen of data monitor mode is displayed.
NOTE:
When malfunction is detected, CONSULT-III perform REAL-TIME DIAGNOSIS.
41
Transmitter function code error
(Front LH)
Function code data from front LH transmitter is malfunction.
42
Transmitter function code error
(Front RH)
Function code data from front RH transmitter is malfunction.
43
Transmitter function code error
(Rear RH)
Function code data from rear RH transmitter is malfunction.
44
Transmitter function code error
(Rear LH)
Function code data from rear LH transmitter is malfunction.
45
Transmitter battery voltage low
(Front LH)
Battery voltage of front LH transmitter drops.
46
Transmitter battery voltage low
(Front RH)
Battery voltage of front RH transmitter drops.
47
Transmitter battery voltage low
(Rear RH)
Battery voltage of rear RH transmitter drops.
48
Transmitter battery voltage low
(Rear LH)
Battery voltage of rear LH transmitter drops.
52
Vehicle speed signal error
Vehicle speed signal error.
53
Control unit
Tire pressure monitoring system malfunction in BCM.
No
blinking
Tire pressure warning check
switch
Tire pressure warning switch circuit is open.
–
Blinking
pattern
Items
Diagnostic items detected when···
Check
item
Revision: 2008 October
2009 Murano
DIAGNOSIS SYSTEM (BCM)
WT-15
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
Also, any malfunction detected while in this mode will be displayed at real time.
Display item list
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may
be different from that displayed on CONSULT-III.
ACTIVE TEST MODE
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction may be differ-
ent from that displayed on CONSULT-III.
TEST ITEM LIST
Monitor
Condition
Specification
AIR PRESS FL
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
• Drive vehicle for a few minutes.
or
• Ignition switch ON and activation tool is trans-
mitting activation signals.
Tire pressure (kPa, kg/cm
2
or Psi)
ID REGST FL
ID REGST FR
ID REGST RR
ID REGST RL
Ignition switch ON
Registration ID: Green
No registration: Red
WARNING LAMP
Low tire pressure warning lamp on: ON
Low tire pressure warning lamp off: OFF
BUZZER
Buzzer in combination meter on: ON
Buzzer in combination meter off: OFF
Test item
Content
WARNING LAMP
This test is able to check to check that the low tire pressure warning lamp turns on.
ID REGIST WARNING
This test is able to check to check that the buzzer sounds or the low tire pressure warning lamp
turns on.
FLASHER
This test is able to check to check that each turn signal lamp turns on.
HORN
This test is able to check to check that the horn sounds.
Revision: 2008 October
2009 Murano
WT-16
< COMPONENT DIAGNOSIS >
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
COMPONENT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
Description
INFOID:0000000003375946
When the tire pressure monitoring system detects low inflation pres-
sure, the low tire pressure warning lamps in the combination meter
comes on.
DTC Logic
INFOID:0000000003375947
DTC DETECTION LOGIC
NOTE: 182.7 kPa (1.9 kg/cm
2
, 26 psi): Standard air pressure is for 230 kPa (2.3 kg/cm
2
, 33 psi) vehicles.
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
2.
Perform BCM self-diagnosis.
Is DTC “C1704”, “C1705”, “C1706”, “C1707” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003375948
1.
CHECK TIRE AIR PRESSURE
1.
Check all tire air pressures.
2.
Adjust all tire air pressures. Refer to
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or replace malfunction parts.
2.
CHECK AIR PRESSURE SIGNAL
1.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
2.
Check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.
SEIA0434E
DTC
Display item
Malfunction detected condition
Possible cause
C1704
LOW PRESSURE FL
Front LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
Tire pressure is low
C1705
LOW PRESSURE FR
Front RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
C1706
LOW PRESSURE RR
Rear RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
C1707
LOW PRESSURE RL
Rear LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less. [NOTE]
Revision: 2008 October
2009 Murano
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-17
< COMPONENT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
Is inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts (tire or wheel). Refer to
WT-102, "Service Notice or Precau-
Special Repair Requirement
INFOID:0000000003523560
1.
CHECK TIRE AIR PRESSURE
Check all tire air pressures. Refer to
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
.
>> END
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at a 40 km/h (25 MPH) or
more for 10 minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2008 October
2009 Murano
WT-18
< COMPONENT DIAGNOSIS >
C1708, C1709, C1710, C1711 TRANSMITTER
C1708, C1709, C1710, C1711 TRANSMITTER
Description
INFOID:0000000003375949
The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave.
DTC Logic
INFOID:0000000003375950
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
2.
Perform BCM self-diagnosis.
Is DTC “C1708”, “C1709”, “C1710”, “C1711” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003375951
1.
CHECK AIR PRESSURE SIGNAL
With CONSULT-III
1.
Start the engine.
2.
Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.
3.
Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR”, “AIR PRESS RL”.
Are all tire pressures displayed 0 kPa?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector and tire pressure receiver harness connector.
: Outside
SEIA0768E
DTC
Display item
Malfunction detected condition
Possible cause
C1708
[NO DATA] FL
Data from front LH transmitter can not receive.
• Harness or connector
(Tire pressure receiver, BCM)
• ID registration is not finished
• Transmitter malfunction
• BCM malfunction
C1709
[NO DATA] FR
Data from front RH transmitter can not receive.
C1710
[NO DATA] RR
Data from rear RH transmitter can not receive.
C1711
[NO DATA] RL
Data from rear LH transmitter can not receive.
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at a 40 km/h (25 MPH) or more for
10 minutes.
Approximately equal to the indication on
vehicle information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2008 October
2009 Murano
C1708, C1709, C1710, C1711 TRANSMITTER
WT-19
< COMPONENT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3.
Check continuity between BCM harness connector and tire pressure receiver harness connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER
Check tire pressure receiver. Refer to
.
Is the inspection result normal?
YES
>> Check BCM pin terminals for damage or loose connection with harness connector. If any items
are damaged, repair or replace damaged parts.
NO
>> Replace the tire pressure receiver.
4.
CHECK ID REGISTRATION
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair
Can ID registration of all transmitters be completed?
YES
>> GO TO 5.
NO
>> Replace malfunctioning transmitter.
5.
CHECK TIRE PRESSURE MONITORING SYSTEM
With CONSULT-III
1.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Check all tire pressures with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace BCM.
Special Repair Requirement
INFOID:0000000003375952
1.
CHECK TIRE AIR PRESSURE
Check all tire air pressures. Refer to
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
138
4
139
2
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
138
139
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at a 40 km/h (25MPH) or
more several minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2008 October
2009 Murano
WT-20
< COMPONENT DIAGNOSIS >
C1708, C1709, C1710, C1711 TRANSMITTER
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
.
>> END
Revision: 2008 October
2009 Murano
C1712, C1713, C1714, C1715 TRANSMITTER
WT-21
< COMPONENT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1712, C1713, C1714, C1715 TRANSMITTER
Description
INFOID:0000000003412912
The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave.
DTC Logic
INFOID:0000000003375954
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
2.
Perform BCM self-diagnosis.
Is DTC “C1712”, “C1713”, “C1714“, ”C1715” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003375955
1.
CHECK ID REGISTRATION
With CONSULT-III
1.
Perform the ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
2.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
3.
Check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK AIR PRESSURE SIGNAL
: Outside
SEIA0768E
DTC
Display item
Malfunction detected condition
Possible case
C1712
[CHECKSUM ERR] FL
Checksum data from front LH transmitter is malfunction.
• Tire pressure receiver malfunc-
tion
• Transmitter malfunction
• BCM malfunction
• Harness or connector
C1713
[CHECKSUM ERR] FR
Checksum data from front RH transmitter is malfunction.
C1714
[CHECKSUM ERR] RR
Checksum data from rear RH transmitter is malfunction.
C1715
[CHECKSUM ERR] RL
Checksum data from rear LH transmitter is malfunction.
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at a 40 km/h (25 MPH) or
more for 10 minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2008 October
2009 Murano
WT-22
< COMPONENT DIAGNOSIS >
C1712, C1713, C1714, C1715 TRANSMITTER
With CONSULT-III
1.
Start the engine.
2.
Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.
3.
Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.
Are all tire pressures displayed 0 kPa?
YES
>> GO TO 3.
NO
>> GO TO 5.
3.
CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector and tire pressure receiver harness connector.
3.
Check continuity between BCM harness connector and tire pressure receiver harness connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK TIRE PRESSURE RECEIVER
Check tire pressure receiver. Refer to
.
Is the inspection result normal?
YES
>> Check BCM pin terminals for damage or loose connection with harness connector. If any items
are damaged, repair or replace damaged parts.
NO
>> Replace the tire pressure receiver.
5.
CHECK ID REGISTRATION
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair
Can ID registration of all transmitters be completed?
YES
>> GO TO 6.
NO
>> Replace malfunctioning transmitter.
6.
CHECK TIRE PRESSURE MONITORING SYSTEM
With CONSULT-III
1.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Check all tire pressure with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at 40 km/h (25 MPH) or more
for 10 minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
138
4
139
2
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
138
139
Revision: 2008 October
2009 Murano
C1712, C1713, C1714, C1715 TRANSMITTER
WT-23
< COMPONENT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace BCM. Refer to
BCS-96, "Removal and Installation"
Special Repair Requirement
INFOID:0000000003375956
1.
CHECK TIRE AIR PRESSURE
Check all tire air pressures. Refer to
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
.
>> END
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at 40 km/h (25 MPH) or more
for several minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2008 October
2009 Murano
WT-24
< COMPONENT DIAGNOSIS >
C1716, C1717, C1718, C1719 TRANSMITTER
C1716, C1717, C1718, C1719 TRANSMITTER
Description
INFOID:0000000003412913
The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave.
DTC Logic
INFOID:0000000003375958
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
2.
Perform BCM self-diagnosis.
Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003375959
1.
CHECK TIRE PRESSURE
With CONSULT-III
1.
Adjust tire pressure to specified value. Refer to
2.
Perform the ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
3.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
4.
Check all tire pressure with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.
Is tire pressure indicated as 438.60 kPa (4.47kg/cm
2
, 63.60 psi) on the “DATA MONITOR” screen?
YES
>> Replace malfunctioning transmitter.
NO
>> GO TO 2.
2.
CHECK TIRE PRESSURE MONITORING SYSTEM
: Outside
SEIA0768E
DTC
Display item
Malfunction detected condition
Possible case
C1716
[PRESSDATA ERR] FL
Air pressure data from front LH transmitter malfunction.
• ID registration is not fin-
ished
• Transmitter malfunction
C1717
[PRESSDATA ERR] FR
Air pressure data from front RH transmitter malfunction.
C1718
[PRESSDATA ERR] RR
Air pressure data from rear RH transmitter malfunction.
C1719
[PRESSDATA ERR] RL
Air pressure data from rear LH transmitter malfunction.
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at 40 km/h (25 MPH) or
more for several minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Revision: 2008 October
2009 Murano
C1716, C1717, C1718, C1719 TRANSMITTER
WT-25
< COMPONENT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
With CONSULT-III
1.
Perform the ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
2.
Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.
3.
Check all tire pressures with CONSULT-III “DATA MONITOR” within 5 minutes.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform the self-diagnosis, inspect detected malfunction. Refer to
MONITOR : Diagnosis Description"
Component Inspection
INFOID:0000000003375960
1.
CHECK TRANSMITTER
With CONSULT-III
1.
Adjust tire pressure to specified value. Refer to
2.
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
3.
Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
4.
Check all tire pressure with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.
Is tire pressure indicated as 438.60 kPa (4.47 kg/cm
2
, 63.60 psi) on the “DATA MONITOR” screen?
YES
>> Replace malfunctioning transmitter.
NO
>> INSPECTION END
Special Repair Requirement
INFOID:0000000003375961
1.
CHECK TIRE AIR PRESSURE
Check all tire air pressures. Refer to
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
Perform ID registration. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
.
>> END
Monitored item
Condition
Display value
AIR PRESS FL
Start the engine and drive at 40 km/h (25 MPH) or
more for 10 minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Monitored item
Condition
Display value
AIR PRESSURE FL
Start the engine and drive at s 40 km/h (25 MPH) or
more several minutes.
Approximately equal to the indication on vehicle in-
formation display.
AIR PRESSURE FR
AIR PRESSURE RR
AIR PRESSURE RL
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст