Nissan Murano Z51 (2008 year). Manual — part 13
BCM (BODY CONTROL MODULE)
ADP-189
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
C1708: [NO DATA] FL
—
—
—
×
C1709: [NO DATA] FR
—
—
—
×
C1710: [NO DATA] RR
—
—
—
×
C1711: [NO DATA] RL
—
—
—
×
C1712: [CHECKSUM ERR] FL
—
—
—
×
C1713: [CHECKSUM ERR] FR
—
—
—
×
C1714: [CHECKSUM ERR] RR
—
—
—
×
C1715: [CHECKSUM ERR] RL
—
—
—
×
C1716: [PRESSDATA ERR] FL
—
—
—
×
C1717: [PRESSDATA ERR] FR
—
—
—
×
C1718: [PRESSDATA ERR] RR
—
—
—
×
C1719: [PRESSDATA ERR] RL
—
—
—
×
C1720: [CODE ERR] FL
—
—
—
×
C1721: [CODE ERR] FR
—
—
—
×
C1722: [CODE ERR] RR
—
—
—
×
C1723: [CODE ERR] RL
—
—
—
×
C1724: [BATT VOLT LOW] FL
—
—
—
×
C1725: [BATT VOLT LOW] FR
—
—
—
×
C1726: [BATT VOLT LOW] RR
—
—
—
×
C1727: [BATT VOLT LOW] RL
—
—
—
×
C1729: VHCL SPEED SIG ERR
—
—
—
×
C1734: CONTROL UNIT
—
—
—
×
CONSULT display
Fail-safe
Freeze Frame
Data
•Vehicle Speed
•Odo/Trip Meter
•Vehicle Condi-
tion
Intelligent Key
warning lamp ON
Tire pressure
monitor warning
lamp ON
Reference
page
Revision: 2008 October
2009 Murano
ADP-190
< SYMPTOM DIAGNOSIS >
ADP SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
ADP SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000003312497
The diagnostics item numbers show the sequence for inspection. Inspection in order from item 1.
Order
Function
Operation procedure
Symptom
Diagnostic item
Reference
page
1
Memory function
Perform memory storage
(Refer to
.) and
memory operation (Refer to
).
All parts do not operate in memory
function.
—
Memory indicator 1 or 2 does not oper-
ate.
—
2
Manual function
Perform manual function
(Refer to
).
All components of power seat do not
operate.
—
All components of tilt&telescopic do not
operate.
—
3
Manual function
and
memory function
Perform manual function
(Refer to
.) and
memory function (Refer to
.).
Manual function or memory function
does not operate. (for specific part)
Sliding
Reclining
Lifting (front)
Lifting (rear)
Steering tilt
Steering telescopic
Door mirror
4
Entry/exit assist
function
Perform entry/exit assist
function.
Exit assist function: Refer
to
Entry assist function: Refer
to
Entry/exit assist function does not op-
erate.
—
5
Intelligent Key in-
ter lock function
Perform Intelligent Key in-
ter lock function (Refer to
).
Intelligent Key inter lock function does
not operate.
—
Revision: 2008 October
2009 Murano
ALL PARTS DO NOT OPERATE IN MEMORY FUNCTION
ADP-191
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
ALL PARTS DO NOT OPERATE IN MEMORY FUNCTION
Diagnosis Procedure
INFOID:0000000003312498
1.
CHECK MEMORY FUNCTION
Check memory function.
Refer to
ADP-22, "MEMORY FUNCTION : System Description"
.
Is the inspection result normal?
YES
>> Memory function is normal.
NO
>> GO TO 2.
2.
CHECK SEAT MEMORY SWITCH
Check seat memory switch.
Refer to
ADP-66, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Check driver seat control unit power supply and ground circuit.
Refer to
ADP-52, "DRIVER SEAT CONTROL UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Check automatic drive positioner control unit power supply and ground circuit.
Refer to
ADP-52, "AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
PERFORM INITIALIZATION AND MEMORY STORING PROCEDURE
1.
Perform initialization procedure.
Refer to
ADP-9, "SYSTEM INITIALIZATION : Special Repair Requirement"
2.
Perform memory storing procedure.
Refer to
ADP-10, "MEMORY STORING : Special Repair Requirement"
.
3.
Check memory function.
Refer to
ADP-22, "MEMORY FUNCTION : System Description"
.
Is the inspection result normal?
YES
>> Memory function is normal.
NO
>> GO TO 6.
6.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2008 October
2009 Murano
ADP-192
< SYMPTOM DIAGNOSIS >
MEMORY INDICATE DOES NOT OPERATE
MEMORY INDICATE DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000003312499
1.
CHECK MEMORY INDICATOR
Check memory indicator.
Refer to
ADP-113, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2008 October
2009 Murano
ALL COMPONENTS OF POWER SEAT DO NOT OPERATE
ADP-193
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
ALL COMPONENTS OF POWER SEAT DO NOT OPERATE
Diagnosis Procedure
INFOID:0000000003312500
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
Check power seat switch ground circuit.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2008 October
2009 Murano
ADP-194
< SYMPTOM DIAGNOSIS >
MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE
MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE
SEAT SLIDING
SEAT SLIDING : Diagnosis Procedure
INFOID:0000000003312501
1.
CHECK SLIDING MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK SLIDING SWITCH
Check sliding switch.
Refer to
ADP-54, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK SLIDING MOTOR
Check sliding motor.
Refer to
ADP-99, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK SLIDING SENSOR
Check sliding sensor.
Refer to
ADP-78, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
CONFIRM THE OPERATION
Check the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
SEAT RECLINING
SEAT RECLINING : Diagnosis Procedure
INFOID:0000000003312502
1.
CHECK RECLINING MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK RECLINING SWITCH
Check reclining switch.
Refer to
ADP-56, "Component Function Check"
Is the inspection result normal?
Revision: 2008 October
2009 Murano
MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE
ADP-195
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK RECLINING MOTOR
Check reclining motor.
Refer to
ADP-101, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK RECLINING SENSOR
Check reclining sensor.
Refer to
ADP-81, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
CONFIRM THE OPERATION
Check the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
SEAT LIFTING (FRONT)
SEAT LIFTING (FRONT) : Diagnosis Procedure
INFOID:0000000003312503
1.
CHECK LIFTING (FRONT) MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK LIFTING SWITCH (FRONT)
Check lifting switch (front).
Refer to
ADP-58, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK LIFTING MOTOR (FRONT)
Check lifting motor (front).
Refer to
ADP-103, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK LIFTING SENSOR (FRONT)
Check lifting sensor (front).
Refer to
ADP-84, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
CONFIRM THE OPERATION
Check the operation again.
Revision: 2008 October
2009 Murano
ADP-196
< SYMPTOM DIAGNOSIS >
MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
SEAT LIFTING (REAR)
SEAT LIFTING (REAR) : Diagnosis Procedure
INFOID:0000000003312504
1.
CHECK LIFTING (REAR) MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK LIFTING SWITCH (REAR)
Check lifting switch (rear).
Refer to
ADP-60, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK LIFTING MOTOR (REAR)
Check lifting motor (rear).
Refer to
ADP-105, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK LIFTING SENSOR (REAR)
Check lifting sensor (rear).
Refer to
ADP-87, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
CONFIRM THE OPERATION
Check the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
STEERING TILT
STEERING TILT : Diagnosis Procedure
INFOID:0000000003312505
1.
CHECK STEERING TILT MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK TILT SWITCH
Check tilt switch.
Refer to
ADP-62, "Component Function Check"
Revision: 2008 October
2009 Murano
MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE
ADP-197
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK TILT MOTOR
Check tilt motor.
Refer to
ADP-107, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK TILT SENSOR
Check steering tilt sensor.
Refer to
ADP-90, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
CONFIRM THE OPERATION
Check the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
STEERING TELESCOPIC
STEERING TELESCOPIC : Diagnosis Procedure
INFOID:0000000003312506
1.
CHECK STEERING TELESCOPIC MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK TELESCOPIC SWITCH
Check telescopic switch.
Refer to
ADP-64, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK TELESCOPIC MOTOR
Check telescopic motor.
Refer to
ADP-109, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK TELESCOPIC SENSOR
Check steering telescopic sensor.
Refer to
ADP-92, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
CONFIRM THE OPERATION
Revision: 2008 October
2009 Murano
ADP-198
< SYMPTOM DIAGNOSIS >
MANUAL FUNCTION OR MEMORY FUNCTION DOES NOT OPERATE
Check the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR MIRROR
DOOR MIRROR : Diagnosis Procedure
INFOID:0000000003312507
1.
CHECK DOOR MIRROR MECHANISM
Check for the following.
• Mechanism deformation or pinched foreign materials.
• Interference with other parts because of poor installation.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
CHECK MIRROR SWITCH
Check mirror switch.
Refer to
ADP-71, "MIRROR SWITCH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunction parts.
3.
CHECK MIRROR MOTOR
Check mirror motor.
Refer to
ADP-111, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CHECK MIRROR SENSOR
Check mirror sensor.
Refer to
ADP-95, "DRIVER SIDE : Component Function Check"
. (Driver side)
ADP-96, "PASSENGER SIDE : Component Function Check"
. (Passenger side)
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunction parts.
5.
CONFIRM THE OPERATION
Check the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2008 October
2009 Murano
ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE
ADP-199
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
ENTRY/EXIT ASSIST FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000003515883
1.
CHECK SYSTEM SETTING
1.
Check system setting.
Refer to
ADP-11, "SYSTEM SETTING : Special Repair Requirement"
.
2.
Check the operation.
Is the inspection result normal?
YES
>> Entry/Exit function is OK.
NO
>> GO TO 2.
2.
PERFORM SYSTEM INITIALIZATION
1.
Perform system initialization.
Refer to
ADP-9, "SYSTEM INITIALIZATION : Special Repair Requirement"
2.
Check the operation.
Is the inspection result normal?
YES
>> Entry/Exit function is OK.
NO
>> GO TO 3.
3.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check front door switch (driver side).
Refer to
DLK-103, "WITH AUTOMATIC BACK DOOR : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunction parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2008 October
2009 Murano
ADP-200
< SYMPTOM DIAGNOSIS >
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
INTELLIGENT KEY INTERLOCK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000003312510
1.
CHECK DOOR LOCK FUNCTION
Check door lock function.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunction parts.
2.
PERFORM MEMORY STORING PROCEDURE
1.
Perform memory storing procedure.
Refer to
ADP-10, "MEMORY STORING : Special Repair Requirement"
2.
Check Intelligent Key interlock function.
Refer to
ADP-34, "INTELLIGENT KEY INTERLOCK FUNCTION : System Description"
.
Is the inspection result normal?
YES
>> Intelligent Key inter lock function is normal.
NO
>> Replace driver seat control unit. Refer to
ADP-204, "Removal and Installation"
Revision: 2008 October
2009 Murano
ALL COMPONENTS OF TILT & TELESCOPIC SWITCH DO NOT OPERATE
ADP-201
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
ALL COMPONENTS OF TILT & TELESCOPIC SWITCH DO NOT OPERATE
Diagnosis Procedure
INFOID:0000000003639907
1.
CHECK TILT & TELESCOPIC SWITCH GROUND CIRCUIT
Check tilt & telescopic switch ground circuit.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2008 October
2009 Murano
ADP-202
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000003312512
The following symptoms are normal operations, and they do not indicate a malfunction.
Symptom
Cause
Action to take
Reference page
Entry/exit assist function and
seat synchronization do not op-
erate.
No initialization has been performed.
Perform initialization.
Entry/exit assist function is disabled.
NOTE:
The entry/exit assist function and seat
synchronization function are disabled be-
fore delivery (initial setting).
Change the settings.
Entry assist function does not op-
erate.
Manual operation with power seat switch
was performed after exit assist function
execution.
Perform the memory
function.
Lumbar support does not per-
form memory operation.
The lumbar support system are con-
trolled independently with no link to the
automatic drive positioner system.
—
Lumbar support system:
Memory function, entry/exit as-
sist function, or Intelligent Key in-
terlock function does not
operate.
The operating conditions are not fulfilled.
Fulfill the operation
conditions.
Memory function:
Exit assist function:
Entry assist function:
Intelligent Key interlock
function:
Revision: 2008 October
2009 Murano
PRECAUTIONS
ADP-203
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003671419
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.
Revision: 2008 October
2009 Murano
ADP-204
< ON-VEHICLE REPAIR >
DRIVER SEAT CONTROL UNIT
ON-VEHICLE REPAIR
DRIVER SEAT CONTROL UNIT
Exploded View
INFOID:0000000003312516
Removal and Installation
INFOID:0000000003312517
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the driver seat (1). Refer to
.
2.
Remove the mounting nut (A).
3.
Remove driver seat control unit (2).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to clump the harness to the right place.
NOTE:
After installing the driver seat, perform additional service when replacing control unit. Refer to
TIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
JMJIA1449ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст