Nissan Murano Z51 (2008 year). Manual — part 112
DLK-324
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
HOOD STAY : Disposal
INFOID:0000000004747887
1.
Fix hood stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the hood stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on hood stay, always cover a hack-
saw using a shop cloth (B) to avoid scattering metal frag-
ments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA3336ZZ
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
Revision: 2008 October
2009 Murano
RADIATOR CORE SUPPORT
DLK-325
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000003470304
Removal and Installation
INFOID:0000000003470305
REMOVAL
1.
Use a refrigerant collecting equipment to discharge the refrigerant. Refer to
2.
Remove front under cover. Refer to
EXT-26, "Removal and Installation"
.
3.
Drain engine coolant from radiator. Refer to
.
4.
Remove front grille. Refer to
EXT-18, "Removal and Installation"
5.
Remove front bumper fascia, energy absorber, bumper reinforcement. Refer to
.
6.
Remove air duct assembly. Refer to
.
7.
Remove hood lock. Refer to
DLK-348, "Removal and Installation"
.
8.
Remove front combination lamp (RH/LH). Refer to
EXL-174, "Removal and Installation"
(XENON TYPE)
EXL-337, "Removal and Installation"
(HALOGEN TYPE).
9.
Disconnect connector of refrigerant pressure sensor. Refer to
.
10. Remove bumper retainer assembly. Refer to
EXT-13, "Removal and Installation"
11. Remove clips, and then remove air guide center and air guide upper.
12. Disengage harness clip from air guide side (RH).
13. Disengage pawls, and then remove air guide side (RH/LH).
14. Remove condenser. Refer to
HA-49, "Removal and Installation"
.
1.
Air guide upper
2.
Air guide side (RH/LH)
3.
Radiator core support
4.
Air guide center
: Pawl
JMKIA1805ZZ
Revision: 2008 October
2009 Murano
DLK-326
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
15. Remove radiator and engine coolant reservoir tank. Refer to
CO-13, "Removal and Installation"
.
CAUTION:
Operate with two workers, because of it is heavy weight.
16. Disconnect connectors of the following parts.
• Ambient sensor. Refer to
VTL-25, "Removal and Installation"
• Cooling fan (RH/LH) and cooling fan control module. Refer to
• Crash zone sensor. Refer to
SR-15, "Removal and Installation"
17. Remove radiator upper hose from radiator core support. Refer to
18. Remove mounting bolt (A) of radiator lower hose bracket (1).
19. Remove radiator lower hose clamp (A) from radiator core sup-
port.
20. Remove power steering oil cooler pipe (1) from radiator core
support.
21. Remove power steering oil cooler pipe clips.
22. Remove all harness clips from radiator core support.
23. Remove mounting bolts, and then remove radiator core support.
CAUTION:
Never damage power steering oil cooler pipe.
24. Remove the following parts after removing radiator core support.
• Ambient sensor. Refer to
VTL-25, "Removal and Installation"
• Cooling fan (RH/LH) and cooling fan control module. Refer to
• Crash zone sensor. Refer to
SR-15, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
: Vehicle front
JMKIA1915ZZ
: Clip
JMKIA1916ZZ
Revision: 2008 October
2009 Murano
FRONT FENDER
DLK-327
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000003470306
Removal and Installation
INFOID:0000000003470307
CAUTION:
Use a shop cloth to protect the body from being damaged during removal and installation.
REMOVAL
1.
Remove clips and remove front fender seal (front/rear).
2.
Remove front grille. Refer to
EXT-18, "Removal and Installation"
3.
Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
4.
Remove front combination lamp. Refer to
EXL-174, "Removal and Installation"
(XENON TYPE),
(HALOGEN TYPE).
5.
Remove fender protector. Refer to
EXT-23, "FENDER PROTECTOR : Removal and Installation"
1.
Front fender seal (front)
2.
Front fender seal (rear)
3.
Front fender assembly
4.
Front fender finisher
5.
Insulator
: Clip
: Pawl
JMKIA1806ZZ
Revision: 2008 October
2009 Murano
DLK-328
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT FENDER
6.
Using remover tool (A), remove front fender finisher (1).
7.
Disengage front part of windshield glass molding from front fender.
8.
Remove mounting bolts and remove front fender.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, peel of the urethane foam bit at a time, and carefully to remove it.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, check front fender adjustment. Refer to
DLK-320, "HOOD ASSEMBLY : Adjust-
DLK-330, "DOOR ASSEMBLY : Adjustment"
.
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
: Clip
: Pawl
JMKIA2261ZZ
Revision: 2008 October
2009 Murano
FRONT DOOR
DLK-329
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000003470308
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000003470309
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove front door harness grommet, and then pull out the harness from the vehicle.
3.
Disconnect front door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-330, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
DLK-330
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000003470310
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door hinge
6.
Rear door hinge (upper)
7.
Rear door hinge (lower)
8.
Door striker
9.
TORX bolt
Refer to
for symbols in the figure.
JMKIA3687GB
Revision: 2008 October
2009 Murano
FRONT DOOR
DLK-331
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit : mm (in)
1.
Remove front fender. Refer to
DLK-327, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install front fender. Refer to refer to
DLK-327, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000004749747
Portion
Clearance
Surface height
Front fender – Front door
A – A
3.4 – 5.4 (0.134 – 0.213)
- 1.0 – 1.0 (- 0.039 – 0.039)
Front door – Rear door
B – B
3.4 – 5.4 (0.134 – 0.213)
- 1.0 – 1.0 (- 0.039 – 0.039)
Front door – Rear door
G – G
2.9 – 5.9 (0.114 – 0.237)
- 1.5 – 1.5 (- 0.059 – 0.059)
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
DLK-332
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR STRIKER : Removal and Installation
INFOID:0000000003470312
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000004749748
DOOR HINGE : Removal and Installation
INFOID:0000000003470314
REMOVAL
1.
Remove front fender. Refer to
DLK-327, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-329, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts, and then remove front door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
FRONT DOOR
DLK-333
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, perform the fitting adjustment. Refer to
DLK-330, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000004749749
DOOR CHECK LINK : Removal and Installation
INFOID:0000000003470316
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "FRONT DOOR FINISHER : Removal and Installation"
2.
Fully close the front door window.
3.
Remove front door speaker.
4.
Remove mounting bolts of door check link on the vehicle.
5.
Remove mounting bolts of door check link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check front door open/close operation after installation.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3688ZZ
Revision: 2008 October
2009 Murano
DLK-334
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
REAR DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000003470317
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000003470318
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove rear door harness grommet, and then pull out door harness from the vehicle.
3.
Disconnect rear door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove rear door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-335, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
REAR DOOR
DLK-335
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY : Adjustment
INFOID:0000000003470319
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door hinge
6.
Rear door hinge (upper)
7.
Rear door hinge (lower)
8.
Door striker
9.
TORX bolt
for symbols in the figure.
JMKIA3687GB
Revision: 2008 October
2009 Murano
DLK-336
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
Unit: mm (in)
1.
Remove center pillar lower garnish. Refer to
INT-19, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting nuts and bolts on body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install center pillar lower garnish. Refer to
INT-19, "Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000004749750
DOOR STRIKER : Removal and Installation
INFOID:0000000003470321
REMOVAL
Portion
Clearance
Surface height
Front door – Rear door
B – B
3.4 – 5.4 (0.134 – 0.213)
-1.0 – 1.0 (-0.039 – 0.039)
Rear door – Body side outer
C – C
3.4 – 5.4 (0.134 – 0.213)
-1.0 – 1.0 (-0.039 – 0.039)
Front door – Rear door
G – G
2.9 – 5.9 (0.114 – 0.237)
-1.5 – 1.5 (-0.059 – 0.059)
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
REAR DOOR
DLK-337
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000004749751
DOOR HINGE : Removal and Installation
INFOID:0000000003470323
REMOVAL
1.
Remove center pillar lower garnish. Refer to
INT-19, "Removal and Installation"
.
2.
Remove rear door assembly. Refer to
DLK-334, "DOOR ASSEMBLY : Removal and Installation"
3.
Remove rear door hinge mounting bolts and nuts (body side), and then remove door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing rear door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
DLK-338
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000004749752
DOOR CHECK LINK : Removal and Installation
INFOID:0000000003470325
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Fully close the rear door window.
3.
Remove rear door speaker.
4.
Remove mounting bolts of the check link on the vehicle.
5.
Remove mounting bolts of the check link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check rear door open/close operation after installation.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
Revision: 2008 October
2009 Murano
BACK DOOR
DLK-339
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Exploded View
INFOID:0000000003470326
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000003470327
CAUTION:
Perform work with 2 workers, because of its heavy weight.
NOTE:
The back door harness constitute the back door assembly.
REMOVAL
1.
Remove back door finisher inner, back door hinge cover, back door plate. Refer to
.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст