Nissan Murano Z51 (2008 year). Manual — part 80
BRC-120
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
STEERING ANGLE SENSOR
STEERING ANGLE SENSOR
Exploded View
INFOID:0000000003247267
Removal and Installation
INFOID:0000000003247268
REMOVAL
1.
Remove spiral cable assembly. Refer to
2.
Remove steering angle sensor from spiral cable assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
After work, make sure to adjust neutral position of steering angle sensor. Refer to
MENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Description"
.
1.
Steering angle sensor
: Vehicle front
JSFIA0003ZZ
Revision: 2008 October
2009 Murano
BRM-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
BRM
A
B
BRM
N
O
P
CONTENTS
BODY REPAIR
FEATURES OF NEW MODEL . . . . . ..
BODY EXTERIOR PAINT COLOR . . . . . .
Body Exterior Paint Color . . . . . . . . . ...
PRECAUTION . . . . . . . . . . . ...
REPAIRING HIGH STRENGTH STEEL . . . ..
High Strength Steel (HSS) . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
REPAIRING MATERIAL . . . . . . . . . .
Foam Repair . . . . . . . . . . . . . . .....
BODY COMPONENT PARTS . . . . . . . .
Underbody Component Parts . . . . . . . . ..
Body Component Parts . . . . . . . . . . ...
ON-VEHICLE MAINTENANCE . . . . .
BODY ALIGNMENT . . . . . . . . . . ...
Body Center Marks . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Engine Compartment . . . . . . . . . . . .
Underbody . . . . . . . . . . . . . . . ...
Passenger Compartment . . . . . . . . . ...
Rear Body . . . . . . . . . . . . . . . ..
ON-VEHICLE REPAIR . . . . . . . . .
HANDLING PRECAUTIONS . . . . . . . .
Precautions for Plastics . . . . . . . . . . ...
Location of Plastic Parts . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
CORROSION PROTECTION . . . . . . .
Description . . . . . . . . . . . . . . . ...
Anti-corrosive Wax . . . . . . . . . . . . ..
Undercoating . . . . . . . . . . . . . . ...
Stone Guard Coat . . . . . . . . . . . . .
Body Sealing . . . . . . . . . . . . . . ...
BODY CONSTRUCTION . . . . . . . . ..
Body Construction . . . . . . . . . . . . ...
REPLACEMENT OPERATIONS . . . . . ...
Description . . . . . . . . . . . . . . . ...
Radiator Core Support . . . . . . . . . . . .
Hoodledge . . . . . . . . . . . . . . . ...
Hoodledge (Partial Replacement) . . . . . . ...
Front Side Member . . . . . . . . . . . . ..
Front Side Member (Partial Replacement) . . ...
Front Pillar . . . . . . . . . . . . . . . ..
Center Pillar . . . . . . . . . . . . . . . .
Outer Sill . . . . . . . . . . . . . . . . .
Rear Fender . . . . . . . . . . . . . . .
Rear Panel . . . . . . . . . . . . . . . ..
Rear Floor Rear . . . . . . . . . . . . . .
Rear Side Member Extension . . . . . . . ...
Revision: 2008 October
2009 Murano
BRM-2
< FEATURES OF NEW MODEL >
BODY EXTERIOR PAINT COLOR
FEATURES OF NEW MODEL
BODY EXTERIOR PAINT COLOR
Body Exterior Paint Color
INFOID:0000000003468450
NOTE:
• 2S: Solid + Clear
• M: Metallic
• P: 2-Coat pearl
• 3P: 3-Coat pearl
• FPM: Iron oxide pearl
• RPM: Multi flex color
• TM: Micro titanium metallic
• PM: Pearl metallic
• TPM: Titanium pearl metallic
JSKIA0574ZZ
Component
Color code
BAX5
BCAB
BKAH
BKH3
BK23
BK51
BQX1
BRAA
Description
Red
Grayish
Brown
Silver
Black
Silver
Gray
White
Dark
Blue
Paint type
Note
P
M
TPM
2S
M
M
3P
PM
Hard clear coat
×
-
-
×
-
-
-
×
1
Bumper fascia
Body color
BAX5
BCAB
BKAH
BKH3
BK23
BK51
BQX1
BRAA
2
Radiator grille
Chromium plate
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Cr
3
Door
outside
mirror
Cover
Body color
BAX5
BCAB
BKAH
BKH3
BK23
BK51
BQX1
BRAA
4
Side guard mold-
ing
Chromium plate
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Cr
5
Back door
Body color
BAX5
BCAB
BKAH
BKH3
BK23
BK51
BQX1
BRAA
6
Door outside
handle
Chromium plate
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Revision: 2008 October
2009 Murano
REPAIRING HIGH STRENGTH STEEL
BRM-3
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
PRECAUTION
REPAIRING HIGH STRENGTH STEEL
High Strength Steel (HSS)
INFOID:0000000003468466
High strength steel is used for body panels in order to reduce vehicle weight.
Accordingly, precautions in repairing automotive bodies made of high strength steel are described below:
Read the following precautions when repairing HSS:
1.
Additional points to consider
• The repair of reinforcements (such as side members) by heat-
ing is not recommended because it may weaken the compo-
nent. When heating is unavoidable, never heat HSS parts
above 550
°
C (1,022
°
F).
Verify heating temperature with a thermometer.
(Crayon-type and other similar type thermometer are appropri-
ate.)
• When straightening body panels, use caution in pulling any
HSS panel. Because HSS is very strong, pulling may cause
deformation in adjacent sections of the body. In this case,
increase the number of measuring points, and carefully pull
the HSS panel.
Tensile strength
Major applicable parts
370 - 590 MPa
• Lower front and rear hoodledge
• Upper hoodledge
• Side dash
• Roof bow No. 2 and No.4
• 3rd crossmember
(Front floor component part)
• Inner sill
• Rear side member assembly
• Rear seat crossmember
• Center rear crossmember assembly
• Inner side roof rail
• Inner center pillar
• Inner center front bumper reinforcement
• Front bumper stay
• Rear side bumper bracket
• Other reinforcements
780 - 1350 MPa
• Front side member assembly
• Front side member closing plate assembly
• Front side member extension
• Front side member center extension
• Outer roof rail reinforcement
(Side body assembly component part)
• 2nd crossmember
(Front floor component part)
PIIA0115E
PIIA0116E
Revision: 2008 October
2009 Murano
BRM-4
< PRECAUTION >
REPAIRING HIGH STRENGTH STEEL
• When cutting HSS panels, avoid gas (torch) cutting if possible.
Instead, use a saw to avoid weakening surrounding areas due
to heat. If gas (torch) cutting is unavoidable, allow a minimum
margin of 50 mm (1.97 in).
• When welding HSS panels, use spot welding whenever possi-
ble in order to minimize weakening surrounding areas due to
heat.
If spot welding is impossible, use MIG. welding. Do not use
gas (torch) for welding because it is inferior in welding
strength.
• Spot welding on HSS panels is harder than that of an ordinary
steel panel.
Therefore, when cutting spot welds on a HSS panel, use a low
speed high torque drill (1,000 to 1,200 rpm) to increase drill bit
durability and facilitate the operation.
2.
Precautions in spot welding HSS
This work should be performed under standard working condi-
tions. Always note the following when spot welding HSS:
• The electrode tip diameter must be sized properly according to
the metal thickness.
PIIA0117E
JSKIA0082GB
PIIA0145E
PIIA0146E
Revision: 2008 October
2009 Murano
REPAIRING HIGH STRENGTH STEEL
BRM-5
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
• The panel surfaces must fit flush to each other, leaving no
gaps.
• Follow the specifications for the proper welding pitch.
Unit: mm (in)
PIIA0147E
Thickness (T)
Minimum pitch (L)
0.6 (0.024)
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.6 (0.063)
1.8 (0.071)
10 (0.39) or more
12 (0.47) or more
18 (0.71) or more
20 (0.79) or more
27 (1.06) or more
31 (1.22) or more
JSKIA0781ZZ
Revision: 2008 October
2009 Murano
BRM-6
< PREPARATION >
REPAIRING MATERIAL
PREPARATION
REPAIRING MATERIAL
Foam Repair
INFOID:0000000004304570
During factory body assembly, foam insulators are installed in certain body panels and locations around the
vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.
URETHANE FOAM APPLICATIONS
Use commercially available Urethane foam for sealant (foam material) repair of material used on vehicle.
Read instructions on product for fill procedures.
Example of foaming agent filling operation procedure
1.
Fill procedures after installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating form insulator and foam material.
c.
Install service part.
d.
Insert nozzle into hole near fill area and fill foam material or fill enough to close gap with the service part.
2.
Fill procedures before installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating foam insulator and foam material.
c.
Fill foam material on wheelhouse outer side.
<Urethane foam for foaming agent>
3M™ Automix™ Flexible Foam 08463 or equiva-
lent
1.
Urethane foam
A.
Nozzle insert hole
: Vehicle front
JSKIA0129GB
Revision: 2008 October
2009 Murano
REPAIRING MATERIAL
BRM-7
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
NOTE:
Fill enough to close gap with service part while avoiding flange
area.
d.
Install service part.
NOTE:
Refer to label for information on working times.
1.
Urethane foam
A.
Fill while avoiding flange area
: Vehicle front
JSKIA0130GB
Revision: 2008 October
2009 Murano
BRM-8
< PREPARATION >
BODY COMPONENT PARTS
BODY COMPONENT PARTS
Underbody Component Parts
INFOID:0000000003468452
1.
Lower rear hoodledge (RH & LH)
2.
Upper hoodledge (RH & LH)
3.
Hoodledge reinforcement (RH & LH)
4.
Center cowl top
5.
Upper dash
6.
Lower dash
7.
Side dash (RH & LH)
8.
Front floor
9.
Inner sill (RH & LH)
JSKIA0576ZZ
Revision: 2008 October
2009 Murano
BODY COMPONENT PARTS
BRM-9
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
NOTE:
For the parts without a number described in the figure, it is supplied only with the assembly part that the part is included with.
10. Rear floor front extension
11.
2nd seat mounting bracket
12. Rear seat back support
13. Rear floor front
14. Rear floor rear
15. Rear floor side (RH & LH)
16. Spare tire clamp bracket
17. Front side member assembly (RH &
LH)
18. Front side member connector as-
sembly (RH & LH)
19. Front side member closing plate as-
sembly (RH & LH)
20. Lower front hoodledge (RH & LH)
21. Side radiator core support (RH & LH)
22. Front side member extension (RH &
LH)
23. Front side member center extension
(RH & LH)
24. Rear seat crossmember
25. Center rear crossmember assembly
26. Spare wheel crossmember
27. Rear side member assembly (RH &
LH)
28. Rear side member extension (RH &
LH)
: Both sided anti-corrosive precoated steel sections
: High strength steel (HSS) sections
: Both sided anti-corrosive steel and HSS sections
Revision: 2008 October
2009 Murano
BRM-10
< PREPARATION >
BODY COMPONENT PARTS
Body Component Parts
INFOID:0000000003468453
1.
Hood
2.
Front fender (RH & LH)
3.
Side body assembly (RH & LH)
4.
Outer front side body (RH & LH)
5.
Front fender bracket assembly (RH
& LH)
6.
Front pillar hinge reinforcement (RH
& LH)
7.
Lower front pillar hinge brace (RH &
LH)
8.
Lower front pillar reinforcement as-
sembly (RH & LH)
9.
Center pillar reinforcement (RH &
LH)
JSKIA0577ZZ
Revision: 2008 October
2009 Murano
BODY COMPONENT PARTS
BRM-11
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
NOTE:
For the parts without a number described in the figure, it is supplied only with the assembly part that the part is included with.
10. Outer sill reinforcement (RH & LH)
11.
Outer sill (RH & LH)
12. Inner side roof rail (RH & LH)
13. Inner center pillar (RH & LH)
14. Inner rear pillar (RH & LH)
15. Inner rear pillar reinforcement (RH &
LH)
16. Back pillar reinforcement assembly
(RH & LH)
17. Outer rear wheelhouse (RH & LH)
18. Outer rear sill reinforcement (RH &
LH)
19. Inner rear wheelhouse (RH & LH)
20. Inner rear wheelhouse front exten-
sion (RH & LH)
21. Inner rear wheelhouse rear exten-
sion (RH & LH)
22. Roof
23. Front roof rail
24. Roof reinforcement assembly
25. Roof bow No. 1
26. Roof bow No. 2
27. Roof bow No. 3
28. Roof bow No. 4
29. Roof bow No. 5
30. Rear roof rail
31. Side roof reinforcement (RH & LH)
32. Rear roof
33. Rear sunroof reinforcement assem-
bly
34. Rear fender assembly (RH & LH)
35. Outer back pillar (RH & LH)
36. Rear combination lamp base (RH &
LH)
37. Rear fascia rear bracket (RH & LH)
38. Rear combination lamp base exten-
sion (RH & LH)
39. Fuel filler lid
40. Rear panel assembly
41. Upper rear bumper retainer
42. Front door assembly (RH & LH)
43. Outer front door panel (RH & LH)
44. Rear door assembly (RH & LH)
45. Outer rear door panel (RH & LH)
46. Inner front bumper center reinforce-
ment
47. Front bumper stay (RH & LH)
48. Inner center rear bumper reinforce-
ment
49. Rear side bumper bracket (RH & LH)
A.
Standard roof
B.
With sunroof
: Both sided anti-corrosive precoated steel sections
: High strength steel (HSS) sections
: Both sided anti-corrosive steel and HSS sections
*: Aluminum portion
Revision: 2008 October
2009 Murano
BRM-12
< ON-VEHICLE MAINTENANCE >
BODY ALIGNMENT
ON-VEHICLE MAINTENANCE
BODY ALIGNMENT
Body Center Marks
INFOID:0000000003468460
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged by an accident which it enables more accurate and effective repair by using
these marks together with body alignment specifications.
Unit: mm (in)
: Vehicle front
Points
Portion
Marks
A
Upper dash
Hole
φ
7 (0.28)
B
Front roof
Embossment
C
Rear roof
Indent
D
Upper rear panel
Indent
JSKIA0558ZZ
Revision: 2008 October
2009 Murano
BODY ALIGNMENT
BRM-13
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Description
INFOID:0000000004292766
• All dimensions indicated in the figures are actual.
• When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself
to make sure there is no free play.
• When a measuring tape is used, check that there is no elongation, twisting, or bending.
• Measurements should be taken at the center of the mounting holes.
• An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side
is symmetrically the same value.
• The coordinates of the measurement points are the distances measured from the standard line of
″
X
″
,
″
Y
″
and
″
Z
″
.
•
″
Z
″
: Imaginary base line [200 mm (7.87 in) below datum line (
″
0Z
″
at design plan)]
Engine Compartment
INFOID:0000000003468462
Measurement
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
E
Front floor reinforcement
Hole
φ
9 (0.35)
F
Front floor
Embossment
Points
Portion
Marks
1.
Vehicle center
2.
Front axle center
3.
Imaginary base line
JSKIA0073GB
Revision: 2008 October
2009 Murano
BRM-14
< ON-VEHICLE MAINTENANCE >
BODY ALIGNMENT
«The others»
Unit: mm (in)
Measurement Points
Unit: mm (in)
JSKIA0544GB
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
B - c
1394 (54.88)*
E - e
1550 (61.02)
Revision: 2008 October
2009 Murano
BODY ALIGNMENT
BRM-15
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Unit: mm (in)
Underbody
INFOID:0000000003468463
Measurement
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
: Vehicle front
JSKIA0545ZZ
Point
Material
Point
Material
A
Cowl top extension installing hole center of cen-
ter positioning mark
φ
7 (0.28)
F, f
Upper radiator core support hole center
φ
12
(0.47)
B, b
Hood hinge installing hole center
φ
13 (0.51)
G, g, K, k, N, n
Front end module installing hole center
φ
9 (0.35)
C, c
Front strut installing hole center 16
×
10
(0.63
×
0.39)
H, h, J, j
Front side member hole center
φ
14 (0.55)
D, d, E, e
Upper front fender bracket installing hole center
φ
7 (0.28)
M, m
Bumper stay installing hole center
φ
12 (0.47)
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст