Nissan Pathfinder (2010 year). Manual — part 545
REAR DRIVE SHAFT
RAX-9
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
• Move the joint up and down, left and right, and in the axial direc-
tion. Check for any rough movement or significant looseness.
• Check the boot for cracks or other damage, and for any grease
leakage.
• If necessary, disassemble the drive shaft, and repair as necessary.
INSTALLATION
Installation is in the reverse order of removal.
• Do not reuse the drive shaft inside flange bolts and washers, discard after removal and use new bolts and
washers for installation.
• Do not reuse the cotter pin, discard after removal and use a new cotter pin for installation.
• Apply Genuine NISSAN grease or equivalent to contact surface between wheel hub and drive shaft. Refer to
.
• Tighten wheel nut to specification. Refer to
RAA0030D
2010 Pathfinder
RAX-10
< DISASSEMBLY AND ASSEMBLY >
REAR DRIVE SHAFT
DISASSEMBLY AND ASSEMBLY
REAR DRIVE SHAFT
Disassembly and Assembly
INFOID:0000000005260152
DISASSEMBLY
Final Drive Side
1. Mount the drive shaft in a vise.
CAUTION:
When mounting the drive shaft in a vise, use copper or aluminum plates between the vise and the
drive shaft.
2. Remove the boot bands.
3. If the plug needs to be removed, move the boot to the wheel side, then drive the plug out using a suitable
plastic hammer.
4. Remove the stopper ring with a flat-bladed screwdriver as
shown, and pull the housing out.
1.
Plug
2.
Housing
3.
Snap ring
4.
Ball cage, steel ball and liner race assembly
5.
Stopper ring
6.
Boot band
7.
Boot
8.
Shaft
9.
Circlip
10. Joint sub-assembly
WDIA0221E
SRA249A
2010 Pathfinder
REAR DRIVE SHAFT
RAX-11
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
5. Remove the snap ring, then remove the ball cage, steel ball and
inner race assembly from the drive shaft.
6. Remove the boot from the drive shaft.
7. Remove any old grease on the housing using paper towels.
Wheel Side
1. Mount the drive shaft in a vise.
CAUTION:
When mounting the drive shaft in a vise, use copper or aluminum plates between the vise and the
drive shaft.
2. Remove the boot bands, then remove the boot from the joint sub-assembly.
3. Screw a suitable drive shaft puller 30 mm (1.18 in) or more into
the threaded part of the joint sub-assembly. Pull the joint sub-
assembly out of the drive shaft as shown.
CAUTION:
• If the joint sub-assembly cannot be removed after five or
more attempts, replace the drive shaft and joint sub-
assembly as a set.
• Align the sliding hammer and drive shaft and remove the
joint sub-assembly by pulling directly.
4. Remove the boot from the drive shaft.
5. Remove the circlip from the drive shaft.
6. While rotating the ball cage, remove any old grease on the joint sub-assembly using paper towels.
INSPECTION AFTER DISASSEMBLY
Drive Shaft
• Replace the drive shaft if there is any runout, cracking, or other damage.
Joint Sub-assembly
• Check for any rough rotation or unusual axial looseness.
• Clean any foreign material from inside the joint sub-assembly.
• Check for any compression scars, cracks, or fractures.
CAUTION:
If any defective conditions are found in the joint sub-assembly components, replace the entire joint
sub-assembly.
NOTE:
Install a new housing, ball cage, steel ball, and inner race as a set.
• Check for any compression scars, cracks, fractures, or unusual wear on the ball rolling surface.
• Check for any damage to the drive shaft screws.
• Check for any deformation of the boot installation components.
Ball Cage
• Check the sliding surface for any compression scars, cracks, or fractures.
Steel Ball
• Check for any compression scars, cracks, fractures, or unusual wear.
Inner Race
SFA514A
SDIA0606E
2010 Pathfinder
RAX-12
< DISASSEMBLY AND ASSEMBLY >
REAR DRIVE SHAFT
• Check the ball sliding surface for any compression scars, cracks, or fractures.
• Check for any damage to the serrated part.
ASSEMBLY
Final Drive Side
1. If the plug has been removed, use Tool to press in a new one.
NOTE:
Discard the old plug and use a new one for assembly.
2. Wrap the serrated part of the shaft with tape. Install the boot
band and boot to shaft.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
3. Remove the tape wound around the serrated part of the shaft.
4. Install the ball cage, steel ball, and inner race assembly on the
shaft, and secure them tightly using the snap ring.
NOTE:
Discard the old snap ring and use a new one for assembly.
5. Insert the specified quantity of Genuine NISSAN Grease or
equivalent, onto the housing (indicated by * marks), and install it
onto shaft. Refer to
.
6. Install the stopper ring onto the housing.
7. After installation, pull on the shaft to check engagement between the joint sub-assembly and the stopper
ring.
Tool number
: KV38100500 ( — )
: KV38102200 ( — )
SDIA1153E
SFA800
SDIA1125E
Grease capacity
: 155
−
175 g (5.47
−
6.17 oz)
RAC0678D
2010 Pathfinder
REAR DRIVE SHAFT
RAX-13
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
8. Install the boot securely into the grooves (indicated by * marks)
as shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by*
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
9. Check that the boot installation length (L) is the length indicated
below. Insert a flat-bladed screwdriver or similar tool into larger
side of boot. Bleed the air from the boot to prevent any boot
deformation.
CAUTION:
• The boot may break if the boot installation length is less than the specified value.
• Do not to touch the tip of the screwdriver to the inside of the boot.
10. Secure the large and small ends of the boot with the new boot
bands as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
11. After installing the housing and shaft, rotate the boot to check that the boot is positioned correctly. If the
boot is not positioned correctly, reposition the boot and secure the boot using a new boot band.
Wheel Side
1. Insert the Genuine NISSAN Grease or equivalent, into the joint
sub-assembly serration hole until the grease begins to ooze
from the ball groove and serration hole. Refer to
. After inserting the grease, use a shop cloth to
wipe off the grease that has oozed out.
2. Wind the serrated part of the shaft with tape. Install the boot
band and boot onto the shaft. Do not damage the boot.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
3. Remove the protective tape wound around the serrated part of
the shaft.
Boot installation length (L)
: 148.7 mm (5.85 in)
WDIA0287E
SFA395
SDIA1127E
SFA800
2010 Pathfinder
RAX-14
< DISASSEMBLY AND ASSEMBLY >
REAR DRIVE SHAFT
4. Attach the circlip to the shaft. The circlip must fit securely into
the shaft groove. Attach the nut to the joint sub-assembly.
Use a soft hammer to press-fit the circlip.
NOTE:
Discard the old circlip and use a new one for assembly.
5. Insert the specified quantity of Genuine NISSAN Grease or
equivalent, into the housing from the large end of the boot. Refer
6. Install the boot securely into the grooves (indicated by the *
marks) as shown.
CAUTION:
If there is grease on the boot mounting surfaces (indicated
by the * marks) of the shaft and housing, the boot may
come off. Remove all grease from the shaft surfaces.
7. Check that the boot installation length (L) is the specified length.
Insert a flat-bladed screwdriver or similar tool into the larger side
of the boot. Bleed the air from the boot to prevent boot deforma-
tion.
CAUTION:
• The boot may break if the boot installation length is less than the specified length.
• Do not contact inside surface of boot with the tip of the screwdriver.
8. Secure large and small ends of the boot using new boot bands
using Tool as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
• Secure boot band so that dimension (M) meets specification
as shown.
9. After installing the joint sub-assembly and shaft, rotate the boot to check that it is positioned correctly. If
the boot is not positioned correctly, reposition the boot and secure the boot using a new boot band.
Grease capacity
: 140
−
160 g (4.94
−
5.64 oz)
RAC0049D
Boot installation length (L)
: 139 mm (5.47 in)
Tool number : KV40107300 ( — )
WDIA0288E
RAC1133D
Dimension (M)
: 1.0 – 4.0 mm (0.039 – 0.157 in)
DSF0047D
2010 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000005260153
Drive Shaft
INFOID:0000000005260154
Boot Bands
INFOID:0000000005260155
Unit: mm (in)
Axial end play
0 mm (0 in)
Joint
Wheel side
Final drive side
Grease capacity
140
−
160 g
(4.94
−
5.64 oz)
155
−
175 g
(5.47
−
6.17 oz)
Boot installed length
139 mm (5.47 in)
148.7 mm (5.85 in)
Dimension (M)
1.0 - 4.0 (0.039 - 0.157)
DSF0047D
2010 Pathfinder
RF-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
RF
A
B
RF
N
O
P
CONTENTS
ROOF
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
INSPECTION AND ADJUSTMENT . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . ...
FUNCTION DIAGNOSIS . . . . . . . ...
SUNROOF SYSTEM . . . . . . . . . . ...
System Diagram . . . . . . . . . . . . . ...
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
RETAINED PWR . . . . . . . . . . . . . .....
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) . . . . . . . . . . . . .....
COMPONENT DIAGNOSIS . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT . ..
SUNROOF MOTOR ASSEMBLY . . . . . . . ..
SUNROOF MOTOR ASSEMBLY :
Diagnosis Procedure . . . . . . . . . . . ..
SUNROOF MOTOR ASSEMBLY : Special Repair
Requirement . . . . . . . . . . . . . . .
SUNROOF SWITCH CIRCUIT . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
DOOR SWITCH . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
ECU DIAGNOSIS . . . . . . . . . . .
BCM (BODY CONTROL MODULE) . . . . .
Reference Value . . . . . . . . . . . . . ..
Terminal Layout . . . . . . . . . . . . . ...
Physical Values . . . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .
Fail Safe . . . . . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ...
SUNROOF SYSTEM . . . . . . . . . . .
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram . . . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
SUNROOF DOES NOT OPERATE PROPER-
LY . . . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
AUTO OPERATION DOES NOT OPERATE .
Diagnosis Procedure . . . . . . . . . . . ...
DOES NOT STOP FULLY-OPEN OR FULLY-
CLOSED POSITION . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
RETAINED POWER OPERATION DOES NOT
OPERATE PROPERLY . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст