Nissan Pathfinder (2010 year). Manual — part 643
TM-272
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
3. Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump bearing.
4. Apply recommended sealant (Genuine RTV Silicone Sealant or
equivalent. Refer to
GI-14, "Recommended Chemical Products
.) to oil pump assembly as shown.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the oil pump bolts and oil pump bolt
mating surfaces.
5. Install O-ring to input clutch assembly.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
6. Tighten oil pump bolts to specified torque.
CAUTION:
Apply ATF to oil pump bushing.
7. Install converter housing to transmission case and tighten bolts
to specified torque.
CAUTION:
Do not reuse self-sealing bolt (A).
SCIA2811E
SCIA5321E
SCIA5011E
Oil pump bolts
: 48 N·m (4.9 kg-m, 35 ft-lb)
SCIA2300E
Converter housing bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt (A)
: 61 N·m (6.2 kg-m, 45 ft-lb)
WCIA0662E
2010 Pathfinder
ASSEMBLY
TM-273
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Make sure that brake band (1) does not close input speed sen-
sor hole (A).
9. Connect TCM connector (1) and transmission range switch con-
nector (2).
10. Install A/T assembly harness connector to control valve with
TCM.
11. Connect TCM connectors.
12. Install O-ring to A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
JSDIA1318ZZ
JSDIA1317ZZ
SCIA5450E
SCIA5447E
SCIA5155E
2010 Pathfinder
TM-274
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
13. Install the A/T fluid temperature sensor 2 or plug as shown below.
a.
A/T fluid temperature sensor 2
i.
Install A/T fluid temperature sensor 2 to bracket.
ii.
Install A/T fluid temperature sensor 2 (with bracket) to control
valve with TCM and tighten bolt to specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
b.
Plug
NOTE:
• When replacing the A/T fluid temperature sensor 2 with the plug, the A/T fluid temperature sensor 2 con-
nector should not be connected.
• Fold the terminal clips.
i.
Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
ii.
Install plug (2) to bracket (1).
SCIA5264E
Bracket bolt
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA5253E
JSDIA1313ZZ
JSDIA1312ZZ
2010 Pathfinder
ASSEMBLY
TM-275
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
iii. Install plug (1) [with bracket (2)] to control valve with TCM and
tighten bolt (
) to specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve.
14. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that input speed sensor is securely installed
into input speed sensor hole (A).
• Hang down output speed sensor harness toward outside
so as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
15. Install bolts (A), (B) and (C) to control valve with TCM.
16. Tighten bolt (1), (2) and (3) temporarily to prevent dislocation.
After that tighten them in order (A
→
B
→
C), and then tighten
other bolts. Tighten control valve with TCM bolts to the specified
torque.
Bracket bolt
: 7.9 N·m (0.81 kg-m, 70 in-lb)
JSDIA1311ZZ
1
: Brake band
JSDIA1318ZZ
SCIA5035E
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8077E
: Front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
SCIA8078E
2010 Pathfinder
TM-276
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
17. After installing the A/T fluid temperature sensor 2, connect the A/T fluid temperature sensor 2 connector
as shown below.
a. Connect A/T fluid temperature sensor 2 connector (A).
b. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips (
).
18. Connect output speed sensor connector (1).
19. Securely fasten output speed sensor harness with terminal clip
(
).
20. Pull down A/T assembly harness connector.
CAUTION:
Do not damage connector.
Tightening torque
N·m (km-g, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8124E
JSDIA1319ZZ
JSDIA1320ZZ
SCIA5299E
2010 Pathfinder
ASSEMBLY
TM-277
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
21. Install snap ring to A/T assembly harness connector.
22. Install magnets in oil pan.
23. Install oil pan to transmission case. Refer to
TM-172, "Removal and Installation"
.
24. Install torque converter.
a. Pour ATF into torque converter.
NOTE:
• Approximately 2 liters (2-1/8 US qt. 1-3/4 Imp qt) of fluid is
required for a new torque converter.
• When reusing old torque converter, add the same amount of
fluid as was drained.
b. Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
CAUTION:
Install torque converter while rotating it.
SCIA5300E
SCIA5200E
SAT428DA
SCIA5010E
2010 Pathfinder
TM-278
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
c.
Measure distance "A" to make sure that torque converter is in
proper position.
Distance “A"
VQ40DE models
: 25.0 mm (0.98 in) or more
VK56DE models
: 24.0 mm (0.94 in) or more
SCIA5694E
2010 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-279
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000005258216
Vehicle Speed at Which Gear Shifting Occurs
INFOID:0000000005258217
VQ40DE MODELS FOR 2WD
At half throttle the accelerator is 1/2 of the full opening.
VQ40DE MODELS FOR 4WD
At half throttle the accelerator is 1/2 of the full opening.
VK56DE MODELS
Applied model
VQ40DE engine
VK56DE engine
2WD
4WD
4WD
Automatic transmission model
RE5R05A
Transmission model code number
3FX3A
3FX2D
94X8C
Stall torque ratio
1.76: 1
1.85: 1
Transmission gear ratio
1st
3.842
3.827
2nd
2.353
2.368
3rd
1.529
1.520
4th
1.000
1.000
5th
0.839
0.834
Reverse
2.765
2.613
Recommended fluid
Genuine NISSAN Matic S ATF
*1
Fluid capacity
10.3 liter (10-7/8 US qt, 9-1/8 Imp qt)
10.6 liter (11-1/4 US qt, 9-3/8 Imp qt)
CAUTION:
If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used. Using automatic transmission
fluid other than Genuine NISSAN Matic S ATF or Matic J ATF will cause deterioration in driveability and automatic transmis-
sion durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited war-
ranty.
Throttle position
Vehicle speed km/h (MPH)
D
1
→
D
2
D
2
→
D
3
D
3
→
D
4
D
4
→
D
5
D
5
→
D
4
D
4
→
D
3
D
3
→
D
2
D
2
→
D
1
Full throttle
62 - 66
(39 - 41)
100 - 108
(63 - 67)
156 - 166
(97 - 103)
241 - 251
(150 - 155)
237 - 247
(148 - 153)
145 - 155
(91 - 96)
88 - 96
(55 - 59)
42 - 46
(27 - 28)
Half throttle
50 - 54
(32 - 33)
82 - 88
(51 - 54)
126 - 134
(79 - 83)
155 - 163
(97 - 101)
126 - 134
(79 - 83)
71 - 79
(45 - 49)
50 - 56
(32 - 34)
11 - 15
(7 - 9)
Throttle position
Vehicle speed km/h (MPH)
D
1
→
D
2
D
2
→
D
3
D
3
→
D
4
D
4
→
D
5
D
5
→
D
4
D
4
→
D
3
D
3
→
D
2
D
2
→
D
1
Full throttle
59 - 63
(37 - 39)
95 - 103
(60 - 64)
147 - 157
(92 - 97)
228 - 238
(142 - 147)
224 - 234
(140 - 145)
137 - 147
(86 - 91)
83 - 91
(52 - 56)
40 - 44
(25 - 27)
Half throttle
47 - 51
(30 - 31)
77 - 83
(48 - 51)
119 - 127
(74 - 78)
147 - 155
(92 - 96)
119 - 127
(74 - 78)
67 - 75
(42 - 46)
48 - 54
(30 - 33)
11 - 15
(7 - 9)
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст