Nissan Pathfinder (2010 year). Manual — part 673
WIPER AND WASHER SYSTEM SYMPTOMS
WW-71
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Front wiper does not
stop.
HI only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
"FR WIP REQ"
IPDM E/R
—
LO only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
"FR WIP REQ"
IPDM E/R
—
INT only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
"FR WIP REQ"
Front wiper does not
operate normally.
Intermittent adjustment
cannot be performed.
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
BCM
—
Intermittent control
linked with vehicle
speed cannot be per-
formed.
Check the vehicle speed detection wiper setting.
Refer to
BCS-23, "WIPER : CONSULT-III Function (BCM - WIPER)"
.
Wiper is not linked to
the washer operation.
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
BCM
—
Does not return to stop
position (Repeatedly
operates for 10 sec-
onds and then stops
for 20 seconds. After
that, it stops the opera-
tion).
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper auto stop signal
circuit
Refer to
.
Rear wiper does not
operate.
ON only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
ON and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
• BCM
• Harness between rear wiper motor and BCM
• Harness between rear wiper motor and ground
• Rear wiper motor
• Glass hatch ajar switch
Combination switch
Refer to
.
Symptom
Probable malfunction location
Inspection item
2010 Pathfinder
WW-72
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Rear wiper does not
stop.
ON only
• Combination switch
• BCM
Rear wiper motor circuit
Refer to
.
INT only
• Combination switch
• BCM
Combination switch
Refer to
Rear wiper does not
operate normally.
Wiper is not linked to
the washer operation.
• Combination switch
• Harness between rear wiper motor and BCM
• BCM
Combination switch
Refer to
BCM
—
Rear wiper does not
return to the Stop posi-
tion (Stops after a five-
second operation).
• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor
Rear wiper auto stop signal
circuit
Refer to
.
Rear wiper stops after
operating for five sec-
onds when ignition
switch is turned ON.
Symptom
Probable malfunction location
Inspection item
2010 Pathfinder
NORMAL OPERATING CONDITION
WW-73
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000005256390
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
2010 Pathfinder
WW-74
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000005256391
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000005256392
Regarding Wiring Diagram information, refer to
.
1.
CHECK WIPER RELAY OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Start IPDM E/R auto active test. Refer to
PCS-12, "Diagnosis Description"
2. Check that the front wiper operates at the LO/HI operation.
CONSULT-III ACTIVE TEST
1. Select "FRONT WIPER" of IPDM E/R active test item.
2. While operating the test item, check front wiper operation.
Is front wiper operation normal?
YES
>> GO TO 5
NO
>> GO TO 2
2.
CHECK FRONT WIPER MOTOR FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the fuse after repairing the applicable circuit.
NO
>> GO TO 3
3.
CHECK FRONT WIPER MOTOR GROUND OPEN CIRCUIT
1. Disconnect front wiper motor.
2. Check continuity between front wiper motor harness connector
and ground.
Does continuity exist?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
LO
: Front wiper LO operation
HI
: Front wiper HI operation
OFF
: Stop the front wiper.
Unit
Location
Fuse No.
Capacity
Front wiper motor
IPDM E/R
39
30 A
Front wiper motor
Ground
Continuity
Connector
Terminal
E23
2
Yes
WKIA3194E
2010 Pathfinder
FRONT WIPER DOES NOT OPERATE
WW-75
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
1. Turn the ignition switch ON.
2. Select "FRONT WIPER" of IPDM E/R active test item.
3. With operating the test item, check voltage between IPDM E/R
harness connector and ground.
Is the measurement value normal?
YES
>> Replace front wiper motor. Refer to
WW-78, "Removal and Installation"
NO
>> Replace IPDM E/R. Refer to
PCS-33, "Removal and Installation of IPDM E/R"
.
5.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "FR WIP REQ" of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the status of "FR WIP REQ".
Is the status of item normal?
YES
>> Replace IPDM E/R. Refer to
PCS-33, "Removal and Installation of IPDM E/R"
.
NO
>> GO TO 6
6.
CHECK COMBINATION SWITCH
1. Perform the inspection of the combination switch. Refer to
Is combination switch normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace the applicable parts.
Terminals
Test item
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Ground
FRONT WIP-
ER
Connector
Terminal
E121
32
LO
Battery
voltage
OFF
0 V
35
HI
Battery
voltage
OFF
0 V
WKIA1427E
Monitor item
Condition
Monitor
status
FR WIP REQ
Front wiper switch HI
HI
ON
STOP
OFF
Front wiper switch LO
1LOW
ON
STOP
OFF
2010 Pathfinder
WW-76
< PRECAUTION >
PRECAUTION
PRECAUTION
PRECAUTION
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005511851
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000005548425
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
2010 Pathfinder
PRECAUTION
WW-77
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
2010 Pathfinder
WW-78
< ON-VEHICLE REPAIR >
FRONT WIPER AND WASHER SYSTEM
ON-VEHICLE REPAIR
FRONT WIPER AND WASHER SYSTEM
Removal and Installation
INFOID:0000000005256394
FRONT WIPER ARMS
Removal
1. Remove wiper arm covers and wiper arm nuts.
2. Remove front RH wiper arm and front LH wiper arm.
3. Remove front RH and LH blade assembly from the front RH and LH arm assembly.
Installation
1. Operate wiper motor one full cycle, then turn "OFF" (Auto Stop).
2. Clean up the pivot area as shown. This will reduce possibility of
wiper arm looseness.
3. Install front RH and LH blade assembly on the front RH and LH arm.
4. Install front RH wiper arm and front LH wiper arm.
5. Ensure that wiper blades stop within proper clearance.
FRONT WIPER ARM ADJUSTMENT
1. Operate windshield washer and wiper motor one full cycle, then turn "OFF" (Auto Stop).
2. Lift the wiper blade up and then rest it onto glass surface, check
the blade clearance "L1" and "L2".
3. Remove wiper arm covers and wiper arm nuts.
4. Adjust front wiper arms on wiper motor pivot shafts to obtain
above specified blade clearances.
5. Tighten wiper arm nuts to specified torque, and install wiper arm
covers.
SEL024J
Clearance "L1"
: 24.5 - 39.5 mm (0.965 - 1.555 in)
Clearance "L2"
: 23.5 - 38.5 mm (0.925 - 1.516 in)
Front wiper arm nuts : 23.6 N·m (2.4 kg-m, 17 ft-lb)
SEL543TA
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст