Nissan Pathfinder (2010 year). Manual — part 475
INT-12
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
Service Notice
INFOID:0000000005256490
• When removing or installing various parts, place a cloth or padding on the vehicle body to prevent scratches.
• Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil or
damage them.
• Apply sealing compound where necessary when installing parts.
• When applying sealing compound, be careful that the sealing compound does not protrude from parts.
• When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust preven-
tion measures.
2010 Pathfinder
PREPARATION
INT-13
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005256491
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000005256492
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle kit
Repairing the cause of noise
SBT839
SBT840
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
2010 Pathfinder
INT-14
< ON-VEHICLE REPAIR >
DOOR FINISHER
ON-VEHICLE REPAIR
DOOR FINISHER
Removal and Installation
INFOID:0000000005256493
FRONT DOOR
Removal
1. Remove the power window switch assembly.
• Disconnect the harness connectors.
2. Remove the pull handle escutcheon.
3. Remove the pull handle cover and remove screw.
4. Lift the armrest upward to release clips and remove armrest.
• Remove the screws behind armrest.
5. Release the clips and remove the door finisher.
1.
Front door
2.
Mirror bolt cover LH
3.
Pull handle escutcheon
4.
Pull handle/lock lever assembly
5.
Pull handle cover
6.
Front door finisher LH
7.
Seat memory switch (if equipped)
8.
Power window/lock switch assembly 9.
Armrest
10. Front door handle bracket
A.
Clip C101
B.
Clip C205
Clip
AWJIA0049GB
2010 Pathfinder
DOOR FINISHER
INT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Disconnect lock cable and handle cable from door handle assembly. Refer to
.
6. Remove the memory seat switch (if equipped).
• Disconnect the harness connector.
7. Remove the pull handle/lock lever assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
Removal
1. Remove the power window switch assembly.
• Disconnect the harness connector.
2. Remove the pull handle cover.
• Remove the screw behind the pull handle cover.
3. Remove the pull handle escutcheon.
4. Lift upward to release clips and remove the armrest.
• Remove the screws behind armrest.
5. Release the clips and remove the rear door finisher.
• Disconnect the rear door tweeter connector, then remove the rear door tweeter screws and remove the
rear door tweeter.
Installation
Installation is in the reverse order of removal.
1.
Rear door
2.
Rear door tweeter
3.
Pull handle/lock lever assembly
4.
Pull handle escutcheon
5.
Pull handle cover
6.
Metal clip
7.
Power window switch assembly
8.
Armrest
9.
Rear door finisher (RH shown)
10. Rear door handle bracket
A.
Clip C101
AWJIA0050GB
2010 Pathfinder
INT-16
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
BODY SIDE TRIM
Component
INFOID:0000000005256494
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear kick plate
5.
Access cover (RH side only)
6.
Center pillar lower finisher
7.
Front kick plate
8.
Lower dash side finisher
9.
Front door welt
10. Front pillar lower finisher
11. Front pillar upper finisher
12. Front pillar assist grip
13. LH side demister grille
14. Molded plastic clip
15. Garnish
C.
Clip C101
D.
Clip C111
E.
Metal clip
Vehicle front
AWJIA0051GB
2010 Pathfinder
BODY SIDE TRIM
INT-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000005256495
LOWER DASH SIDE FINISHER
Removal
1. Remove the push pin from lower dash side finisher.
2. Remove the front kick plate from center pillar lower finisher.
3. Remove the lower dash side finisher and the front kick plate together.
4. Remove the lower dash side finisher from the front kick plate.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
Removal
1. Remove the seat belt anchor. Refer to
SB-12, "Removal and Installation"
• On RH side, disconnect seat belt tension sensor.
2. Remove the front and rear kick plates.
3. Remove the center pillar lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1. Remove the front and rear door welts.
2. Remove the seat belt shoulder anchor and D-ring. Refer to
SB-12, "Removal and Installation"
.
3. Remove the front and rear kick plates.
4. Remove the center pillar lower finisher.
5. Remove the center pillar assist grip.
6. Remove the center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR UPPER FINISHER
Removal
1. Remove the front pillar assist grip.
2. Remove the front pillar upper finisher bolt.
3. Remove the front pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR LOWER FINISHER
Removal
1. Partially remove the front door welt.
2. Remove the front pillar lower finisher.
Installation
Installation is in the reverse order of removal.
KICK PLATES
Removal
Release clips and remove the front and/or rear kick plates.
Installation
Installation is in the reverse order of removal.
2010 Pathfinder
INT-18
< ON-VEHICLE REPAIR >
FLOOR TRIM
FLOOR TRIM
Removal and Installation
INFOID:0000000005256496
Front and Rear Floor Carpet
REMOVAL
Front Carpet
1. Remove the front seats. Refer to
SE-30, "Removal and Installation"
.
2. Remove the lower seat belt anchors. Refer to
SB-12, "Removal and Installation"
3. Remove the lower body side trim panels. Refer to
INT-17, "Removal and Installation"
4. Remove the center console. Refer to
IP-12, "Removal and Installation"
.
5. Remove the floor mat hooks from the front carpet.
6. Remove the front carpet.
Rear Carpet
1. Remove the second and third row seats. Refer to
SE-31, "Removal and Installation"
2. Remove the luggage side lower finisher RH and LH. Refer to
INT-22, "Removal and Installation"
3. Remove the flipper doors and the floor tray. Refer to
INT-22, "Removal and Installation"
.
4. Remove the bolts and the storage box. Refer to
INT-22, "Removal and Installation"
5. Remove the rear carpet.
INSTALLATION
Installation is in the reverse order of removal.
AWJIA0411ZZ
1.
Front carpet
2.
Floor mat hooks
3.
Rear carpet
A.
Clip C103
Vehicle front
2010 Pathfinder
HEADLINING
INT-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
Removal and Installation
INFOID:0000000005256497
REMOVAL
1. Remove the body side trim panels. Refer to
.
2. Remove the luggage floor trim upper panels. Refer to
.
3. Remove the sun visor assemblies, both LH and RH.
4. Remove the sun visor holders LH and RH.
5. Remove the sunroof welt (if equipped).
6. Remove the DVD video monitor assembly (if equipped). Refer to
AV-148, "Removal and Installation of
(Mid audio),
AV-301, "Removal and Installation of Video Monitor"
navigation) and
AV-468, "Removal and Installation of Video Monitor"
1.
Sun visor holder LH/RH
2.
Sun visor assembly RH
3.
Front assist grip RH
4.
Rear assist grip RH
5.
Front roof console with front room
lamp assembly and sunglass bin
6.
Sunroof welt (if equipped)
7.
DVD video monitor finisher (if
equipped)
8.
Center room lamp assembly
9.
Rear room lamp assembly
10. Rear assist grip LH
11. Headlining
12. Sun visor assembly LH
A.
Clip C103
Vehicle front
Metal clip
AWJIA0052GB
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст