Nissan Pathfinder (2010 year). Manual — part 478
IP-12
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INFOID:0000000005259201
INSTRUMENT PANEL
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery terminals, then wait at least
three minutes.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2. Remove the center console. Follow the CENTER CONSOLE Removal procedure.
3. Remove the combination meter. Refer to
MWI-96, "Removal and Installation"
4. Remove front pillar upper finisher. Refer to
INT-17, "Removal and Installation"
.
5. Remove optical sensor. Refer to
EXL-150, "Removal and Installation"
.
6. Remove AV control unit. Refer to
AV-34, "Removal and Installation"
for BASE AUDIO,
AV-289, "Removal and Installation"
for BOSE AUDIO WITHOUT NAVI-
GATION, or
AV-460, "Removal and Installation"
for BOSE AUDIO WITH NAVIGATION.
7. Remove display unit, if equipped. Refer to
AV-143, "Removal and Installation"
for BOSE AUDIO WITHOUT NAVIGATION, or
AV-462, "Removal and Installa-
for BOSE AUDIO WITH NAVIGATION.
8. Remove cluster lid D. Follow the CLUSTER LID D Removal procedure.
9. Disconnect GPS antenna.
10. Remove the passenger air bag module. Refer to
SR-9, "Removal and Installation"
11. Remove the instrument stay RH/LH bolts.
12. Remove instrument panel and pad assembly.
• Disconnect all remaining harnesses.
Installation
Installation is in the reverse order of removal.
CLUSTER LID C -WITHOUT DISPLAY UNIT
Removal
CAUTION:
16. Center ventilator grill RH/LH
17.
Cluster lid D
18. AV control unit
19. A/C and AV switch assembly
20.
Lower glove box latch assembly
21. Lower glove box
22. Fuse block cover
23.
Lower glove box damper assembly 24. Lower instrument panel RH
25. Upper glove box door
26.
Upper glove box
27. Instrument side finisher
28. Instrument panel and pad assembly 29.
Passenger air bag module
AWJIA0463ZZ
1.
Storage tray
2.
Cluster lid C
3.
Cluster lid C screw
2010 Pathfinder
INSTRUMENT PANEL ASSEMBLY
IP-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Before servicing, turn the ignition switch off, disconnect both battery cables and wait at lease three
minutes.
1. Remove A/T finisher. Follow the A/T FINISHER removal procedure.
2. Remove storage tray, then remove cluster lid C screw.
3. Pull cluster lid C rearward to release clips.
4. Disconnect harness connectors, then remove cluster lid C.
Installation
Installation is in the reverse order of removal.
CLUSTER LID C - WITH DISPLAY UNIT
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery terminals, then wait at least
three minutes.
1. Select neutral, then remove shift lever handle.
2. Remove A/T finisher.
3. Remove the center console bin screws and center console bin.
4. Remove cluster lid C bolts, then release the clips and remove cluster lid C.
5. Disconnect electrical connectors and remove cluster lid C.
Installation
Installation is in the reverse order of removal.
AWJIA0055ZZ
1.
Instrument panel
2.
Cluster lid C
A.
Cluster lid C bolt
Clip C103
Metal clip
2010 Pathfinder
IP-14
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
CLUSTER LID D
Removal
1. Remove A/T finisher.
2. Remove lower instrument panel LH.
3. Remove lower instrument panel RH.
4. Remove cluster lid C.
5. Disconnect the electrical connectors and remove cluster lid D.
Installation
Installation is in the reverse order of removal.
LOWER INSTRUMENT PANEL LH
Removal
1. Remove front pillar lower finisher. Refer to
INT-17, "Removal and Installation"
.
2. Remove lower instrument panel LH, using power tool.
3. Pull rearward to release lower instrument panel LH.
4. Disconnect lower instrument panel LH harness connectors.
Installation
Installation is in the reverse order of removal.
AWJIA0056ZZ
1.
Cluster lid D
A.
Cluster lid D screw
LIIA1744E
2010 Pathfinder
INSTRUMENT PANEL ASSEMBLY
IP-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CLUSTER LID A
Removal
1. Remove front pillar upper finisher. Refer to XX-XX, "*****".
2. Remove lower instrument panel LH. Refer to LOWER INSTRUMENT PANEL LH in this section.
3. Remove steering lock escutcheon.
4. Remove the screws and clips, then lift cluster lid A rearward in vehicle away from the instrument panel.
Installation
Installation is in the reverse order of removal.
STEERING COLUMN COVER
Removal
1. Partially remove driver door weatherstrip and set aside.
2. Remove front pillar lower finisher. Refer to
INT-17, "Removal and Installation"
.
3. Remove lower intstrument panel LH. Refer to LOWER INSTRUMET PANEL LH in this section.
4. Remove the steering column cover screws, then remove both the upper and lower portions of the steering
column cover.
Installation
Installation is in the reverse order of removal.
A/T FINISHER
Removal
1. Remove cup holder finisher.
2. Release the shift lever handle clip, then remove shift lever handle. Refer to
.
ALJIA0460ZZ
1.
Combination meter
2.
Cluster lid A
3.
Ignition key lamp assembly
4.
Steering lock escutcheon
Metal clip
AWJIA0057ZZ
1.
Cluster lid D
2.
Center console front base
3.
Cup holder finisher
4.
A/T finisher
Front
2010 Pathfinder
IP-16
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
3. Pull up to release clips and disconnect the connectors, then remove the A/T finisher.
Installation
Installation is in the reverse order of removal.
LOWER INSTRUMENT PANEL RH AND LOWER GLOVE BOX
Removal
1. Disconnect the negative battery terminal.
2. Remove front pillar lower finisher. Refer to
INT-17, "Removal and Installation"
.
3. Remove lower instrument panel RH screws, using power tool.
4. Remove lower instrument panel RH and lower glove box.
Installation
NOTE:
Install upper glove box before installing lower glove box.
Installation is in the reverse order of removal.
UPPER GLOVE BOX
Removal
1. Remove lower instrument panel RH and lower glove box.
2. Remove cluster lid C.
3. Remove upper glove box screws, using power tool.
4. Remove upper glove box.
Installation
Installation is in the reverse order of removal.
CENTER CONSOLE
Removal
1. Remove lower instrument panel RH and glove box. Refer to LOWER INSTRUMENT PANEL RH AND
GLOVE BOX in this section.
2. Remove cup holder finisher.
3. Remove A/T finisher. Refer to AT FINISHER in this section.
4. Remove center console screws, then lift center console rear base away from center console front base
and disconnect harness connectors.
: Vehicle front
5. Disconnect harness connectors, then remove center console front base.
WIIA1058E
2010 Pathfinder
INSTRUMENT PANEL ASSEMBLY
IP-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Installation
Installation is in the reverse order of removal.
2010 Pathfinder
IP-18
< DISASSEMBLY AND ASSEMBLY >
CENTER CONSOLE ASSEMBLY
DISASSEMBLY AND ASSEMBLY
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000005259202
Disassembly and Assembly
INFOID:0000000005259203
LOWER GLOVE BOX
Disassembly
1. Remove fuse block cover.
2. Remove damper hook.
3. Remove lower glove box latch cover.
4. Remove lower glove box latch assembly.
Assembly
Assembly is in the reverse order of disassembly.
UPPER GLOVE BOX
Disassembly
1. Remove upper glove box door screws.
2. Remove upper glove box door.
1.
Upper glove box
2.
Upper glove box door
3.
Lower instrument panel RH
4.
Fuse block cover
5.
Lower glove box latch assembly cover 6.
Lower glove box
7.
Lower glove box latch assembly
8.
Damper hook
9.
Lower glove box damper
WIIA1049E
2010 Pathfinder
CENTER CONSOLE ASSEMBLY
IP-19
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Assembly
Assembly is in the reverse order of disassembly.
Center Console
Disassembly
1. Remove center console. Refer to
IP-12, "Removal and Installation"
2. Remove center console lid.
3. Remove latch from center console lid.
4. Remove hinge from center console lid.
5. Remove rear finisher assembly.
6. Remove rear cup holder assembly.
7. Remove DVD player, if equipped. Refer to
AV-148, "Removal and Installation of DVD Player"
AV-301, "Removal and Installation of DVD Player"
for BOSE AUDIO WITHOUT NAVIGATION, or
AV-468, "Removal and Installation of DVD Player"
for BOSE AUDIO WITH NAVIGATION.
8. Disconnect center console harness connectors.
9. Remove cup holder insert and cup holder assembly.
10. Remove center console bin.
11. Remove center console bracket.
AWJIA0058ZZ
1.
Console bin
2.
A/T finisher
3.
Ash tray
4.
Center console front base
5.
Cup holder finisher
6.
Bracket
7.
Center console rear base
8.
Bracket DVD
9.
Wire harness bracket
10. Rear finisher assembly
11. Rear cup holder assembly
12. Ventilator console grille (if equipped)
13. Rear air control (rear) (if equipped) 14. Hinge
15. Center console lid
16. Center console bin
17. Cup holder insert
18. Cup holder assembly
A.
Screw
B.
Bolt
Vehicle front
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст