Nissan Pathfinder (2010 year). Manual — part 93
BR-14
< BASIC INSPECTION >
BRAKE TUBE AND HOSE
ABS Actuator and Electric Unit Brake Pipe Connections for VK56DE
AWFIA0593GB
1.
To rear left disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
2.
To rear right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
3.
To front left disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
4.
To front right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
5.
From the master cylinder secondary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
6.
From the master cylinder primary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
7.
ABS actuator and electric unit
(control unit)
8.
Harness connector
9.
Grommet
10. Collar
Front
2010 Pathfinder
BRAKE TUBE AND HOSE
BR-15
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
ABS Actuator and Electric Unit Brake Pipe Connections for VQ40DE
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning the steering wheel both clockwise
and counterclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• When removing components, cover connections so that no dirt, dust, or other foreign matter gets in.
• Refill with new specified brake fluid. Refer to
.
• Do not reuse drained brake fluid.
FRONT BRAKE
FRONT BRAKE : Inspection
INFOID:0000000005260199
INSPECTION AFTER REMOVAL
CAUTION:
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
ALFIA0146ZZ
1.
From master cylinder secondary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
2.
To rear right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
3.
To rear left disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
4.
To front right disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
5.
To front left disc brake
13.0 N·m (1.3 kg-m, 10 ft-lb)
6.
From master cylinder primary side
18.2 N·m (1.9 kg-m, 13 ft-lb)
7.
ABS actuator and electric unit (control
unit)
8.
Harness connector
Front
2010 Pathfinder
BR-16
< BASIC INSPECTION >
BRAKE TUBE AND HOSE
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, contact
with other parts, and loose connections. Replace any parts as necessary. Refer to
2. While depressing brake pedal under a force of 785 N (80 kg-f, 177 lb-f) with engine running for approxi-
mately 5 seconds, check each part for fluid leaks.
REAR BRAKE
REAR BRAKE : Inspection
INFOID:0000000005260200
INSPECTION AFTER REMOVAL
CAUTION:
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, contact
with other parts, and loose connections. Replace any parts as necessary. Refer to
2. While depressing brake pedal under a force of 785 N (80 kg-f, 177 lb-f) with engine running for approxi-
mately 5 seconds, check each part for fluid leaks.
2010 Pathfinder
BRAKE PEDAL
BR-17
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
ON-VEHICLE MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment - Standard Pedal
INFOID:0000000005260201
INSPECTION
1. Inspect the brake pedal free height (H) from the floor using Tool
at a 90
°
angle to the floor as shown.
2. Adjust the brake pedal height to specifications.
Brake Pedal Specifications
Unit: mm (in)
ADJUSTMENT
1. Loosen the stop lamp switch and ASCD cancel switch by turning 45
°
counterclockwise.
Tool number :
—
(J-46532)
AWFIA0557ZZ
Pedal free height (H)
Refer to
.
Pedal full stroke (S)
[Depressed under a force of 490 N (50 kg, 110 lb) with engine running]
Refer to
.
Clearance between pedal stopper and threaded end of stop lamp switch and ASCD
switch (C
1
) or (C
2
)
Refer to
.
2010 Pathfinder
BR-18
< ON-VEHICLE MAINTENANCE >
BRAKE PEDAL
2. Loosen lock nut (A) on the input rod, then turn input rod to adjust
the brake pedal to specified height. When finished adjusting,
tighten lock nut (A) to specification.
CAUTION:
Make sure that the screw portion of the end of input rod is
located inside the clevis.
3. With the brake pedal pulled up and held by hand, press the stop
lamp switch and the ASCD cancel switch in until threaded ends
contact the brake pedal bracket.
4. With the threaded ends of the stop lamp switch and ASCD
switch contacting the pedal bracket, turn the switches 45
°
clock-
wise to lock in place. Check that the stop lamp switch and ASCD
cancel switch threaded end to brake pedal bracket gap (C) is
within specifications.
CAUTION:
Make sure that the gap (C) between the brake pedal bracket
and stop lamp switch and ASCD cancel switch threaded
ends are within specification.
5. Check the brake pedal for smooth operation.
CAUTION:
Make sure that the stop lamp goes off when the brake pedal
is released.
6. Start the engine and check the height of the brake pedal when depressing it.
Inspection and Adjustment - Adjustable Pedal
INFOID:0000000005260202
INSPECTION
1. Inspect the brake pedal free height (H) from the floor using Tool
at a 90
°
angle to the floor as shown.
2. Adjust the height referring to the following specifications.
CAUTION:
When equipped with adjustable pedal, the pedal must be in
the forward most (closest to the floor) position for pedal
height measurement.
Brake Pedal Specifications
Unit: mm (in)
Lock nut (A)
: 18.7 N·m (1.9 kg-m, 14 ft-lb)
PFIA0436E
Tool number :
—
(J-46532)
ALFIA0149ZZ
Pedal free height (H) with pedal in forward most position
Refer to
2010 Pathfinder
BRAKE PEDAL
BR-19
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
CAUTION:
When equipped with adjustable pedal, the pedal must be in the forward most position (closest to the floor) for pedal
height adjustment.
ADJUSTMENT
1. Loosen the stop lamp switch and ASCD cancel switch by turning them 45
°
counterclockwise.
2. Loosen lock nut (A) on the input rod, then turn input rod to adjust
the brake pedal to the specified height. When finished adjusting,
tighten the lock nut (A) to specification.
CAUTION:
Make sure that the screw portion of the end of input rod is
located inside the clevis.
3. With the brake pedal pulled up and held by hand, press the stop
lamp switch and the ASCD cancel switch in until the threaded
ends contact the brake pedal bracket.
4. With the threaded ends of the stop lamp switch and ASCD
switch contacting the pedal bracket, turn the switches 45
°
clock-
wise to lock in place. Check that the stop lamp switch and ASCD
cancel switch threaded end to brake pedal bracket gap (C) is
within specifications.
CAUTION:
Make sure that the gap (C) between the brake pedal bracket
and stop lamp switch and ASCD cancel switch threaded
ends are within specification.
5. Check the brake pedal for smooth operation.
CAUTION:
Make sure that the stop lamp goes off when the brake pedal
is released.
6. Start the engine and check the height of the brake pedal when depressing it.
Pedal travel (T)
[Depressed under a force of 490 N (50 kg, 110 lb) with engine running]
Refer to
.
Clearance between pedal stopper and threaded end of stop lamp switch and ASCD switch
Refer to
.
Lock nut (A)
: 18.7 N·m (1.9 kg-m, 14 ft-lb)
PFIA0436E
2010 Pathfinder
BR-20
< ON-VEHICLE MAINTENANCE >
BRAKE FLUID
BRAKE FLUID
On Board Inspection
INFOID:0000000005260203
LEVEL CHECK
• Check that the brake fluid level in the reservoir tank is within speci-
fication, between the MAX and MIN lines as shown.
• Visually check around reservoir tank for fluid leaks.
• If fluid level is excessively low, check brake system for leaks.
• If brake warning lamp remains illuminated after the parking brake
pedal is released, check the brake system for any brake fluid
leaks.
Drain and Refill
INFOID:0000000005260204
CAUTION:
• Refill with new brake fluid. Refer to
• Do not reuse drained brake fluid.
• Do not let brake fluid splash on the painted surfaces of the body. This might damage the paint, so
when splashing it, immediately wipe off the area and wash away with water.
• Before servicing, disconnect ABS actuator and electric unit (control unit) connector or battery nega-
tive terminal.
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector or battery
negative terminal.
2. Connect a vinyl tube to each bleed valve.
3. Depress brake pedal, loosen each bleed valve, and gradually
remove brake fluid.
4. Make sure there is no foreign material in reservoir tank, and refill
with new brake fluid.
5. Rest foot on brake pedal. Loosen bleed valve. Slowly depress
brake pedal until it stops. Tighten bleed valve. Release brake
pedal. Repeat the process a few times, then pause to add new
brake fluid to master cylinder. Continue until the new brake fluid
flows out of the bleed valve.
Bleed the air out of the brake hydraulic system. Refer to
.
Bleeding Brake System
INFOID:0000000005260205
CAUTION:
• Refill with new brake fluid. Refer to
• Do not reuse drained brake fluid.
LFIA0234E
BRA0007D
PFIA0403J
2010 Pathfinder
BRAKE FLUID
BR-21
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
• Do not let brake fluid splash on the painted surfaces of the body. This might damage the paint, so
when splashing it, immediately wipe off the area and wash away with water.
• Before servicing, disconnect ABS actuator and electric unit (control unit) connector or battery nega-
tive terminal.
• While bleeding, monitor the master cylinder brake fluid level.
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector or battery
negative terminal.
2. Connect a vinyl tube to the rear right bleed valve.
3. Fully depress brake pedal 4 to 5 times.
4. With brake pedal depressed, loosen bleed valve to let the air out, and then tighten it immediately.
5. Repeat steps 3 and 4 until no more air comes out.
6. Tighten bleed valve to the specified torque. Refer to
BR-40, "Exploded View of Brake Caliper"
(front disc
BR-45, "Exploded View of Brake Caliper"
(rear disc brake).
7. Perform steps 2 to 6 at each wheel, with master cylinder reservoir tank filled at least half way, bleed air
from the front left, rear left, and front right bleed valve, in that order.
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст