Nissan Pathfinder (2010 year). Manual — part 555
RSU-18
< REMOVAL AND INSTALLATION >
STABILIZER BAR
STABILIZER BAR
Removal and Installation
INFOID:0000000005260318
REMOVAL
1. Disconnect the stabilizer bar ends from the connecting rods
using power tool.
2. Remove the stabilizer bar clamps using power tool, and remove
the stabilizer bar bushings.
3. Remove the stabilizer bar.
INSPECTION AFTER REMOVAL
• Check stabilizer bar for any deformation, cracks, or damage and replace if necessary.
• Check rubber bushings for deterioration, or cracks and replace if necessary.
INSTALLATION
Installation is in the reverse order of removal.
• Install the stabilizer bar bushings and clamps so they are posi-
tioned outside of the sideslip prevention clamp on the stabilizer
bar.
• Tighten the nuts and bolts to specification. Refer to
LEIA0111E
LEIA0113E
LEIA0112E
2010 Pathfinder
REAR SUSPENSION MEMBER
RSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION MEMBER
Removal and Installation
INFOID:0000000005260313
COMPONENTS
REMOVAL
1. Remove both of the rear wheel and tire assemblies using power tool.
2. Remove the spare tire.
1.
Seat belt latch anchor
2.
Stabilizer bar bushing
3.
Stabilizer bar clamp
4.
Stabilizer bar
5.
Connecting rod
6.
Front lower link
7.
Knuckle
8.
Bushing
9.
Rear lower link
10. Shock absorber
11. Suspension arm
12. Lower rubber seat
13. Coil spring
14. Upper rubber seat
15. Rear suspension member
16. Spare tire bracket
17. Bound bumper
AWEIA0022GB
2010 Pathfinder
RSU-20
< REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
3. Remove the brake caliper without disconnecting the brake hoses, using power tool. Reposition the brake
caliper out of the way using a suitable wire. Refer to
BR-45, "Removal and Installation of Brake Caliper
.
CAUTION:
• Do not crimp or stretch the brake hose when repositioning the brake caliper out of the way.
• Do not press the brake pedal while the brake caliper is positioned out of the way.
4. Remove the two rear brake rotors.
5. Remove the two rear drive shafts. Refer to
RAX-8, "Removal and Installation"
6. Disconnect the parking brake cables brackets from the rear suspension member.
7. Disconnect the two rear wheel sensor connectors and harness clips.
8. Remove the rear final drive vent tube from the rear suspension member and frame.
9. Remove the rear final drive. Refer to
DLN-422, "Removal and Installation"
10. Set a suitable jack to support each of the rear lower links and the
coil spring tension.
11. Remove both of the rear lower link outer bolts using power tool,
and lower the jack to remove the rear coil springs, and the upper
and lower rubber seats.
12. Remove the two bolts to disconnect the seat belt latch anchor
from the rear suspension member using power tool.
13. Disconnect both of the connecting rods from the rear stabilizer
bar.
LEIA0077E
LEIA0109E
LEIA0111E
2010 Pathfinder
REAR SUSPENSION MEMBER
RSU-21
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
14. Set a suitable jack under each front lower link for support and
remove the shock absorber upper end bolts and lower end bolts
using power tool.
15. Remove both of the shock absorbers.
16. Set a suitable jack under the rear suspension member.
17. Remove the six rear suspension member bolts using power tool.
18. Slowly lower the jack supporting the rear suspension member to
access the fuel filler tube bracket, then remove the two bolts to
disconnect the fuel filler tube bracket from the rear suspension
member.
19. Slowly lower the jack to remove the rear suspension member, suspension arm, front and rear lower links,
knuckles, and stabilizer bar as an assembly.
20. Remove the suspension arm, spare tire bracket, stabilizer bar, front and rear lower links, and the knuckles
from the rear suspension member using power tool.
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, and other damage and replace if necessary.
INSTALLATION
Installation is in the reverse order of removal.
• When raising the rear suspension member assembly, use the
locating pins to align the rear suspension member to the vehicle
body.
LEIA0110E
LEIA0114E
LEIA0083E
2010 Pathfinder
RSU-22
< REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
• When installing the upper and lower rubber seats for the rear coil
springs, the arrow embossed on the rubber seats must point out
toward the wheel and tire assembly.
• Perform final tightening of the nuts and bolts for the links (with rubber bushings) under unladen conditions
with the tires on level ground.
• Adjust the parking brake cables. Refer to
.
• Check the wheel alignment. Refer to
FSU-6, "Front Wheel Alignment"
.
LEIA0076E
2010 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-23
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment (Unladen*)
INFOID:0000000005260319
*1: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designed positions.
Camber
Degree minute (decimal degree)
Minimum
- 0
°
32
′
(- 0.53
°
)
Nominal
- 0
°
2
′
(- 0.03
°
)
Maximum
0
°
28
′
(0.47
°
)
Total toe-in
Distance difference between right and
left side (AR-BR)-(AL-BL)
:Front
Minimum
-2 mm (-0.08 in)
Nominal
0 mm (0 in)
Maximum
2 mm (0.08 in)
Distance [left side (AL-BL) or right
side (AR-BR)] from center line of body
Minimum
- 1.4 mm (- 0.055 in)
Nominal
1.9 mm (0.075 in)
Maximum
5.2 mm (0.205 in)
Angle (left side or right side)
Degree minute (decimal degree)
Minimum
- 0
°
3' (-0.05
°
)
Nominal
0
°
4' (0.07
°
)
Maximum
0
°
11' (0.18
°
)
ALEIA0059ZZ
2010 Pathfinder
RSU-24
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Ball Joint
INFOID:0000000005260320
*: Measurement point is at the bolt groove of the ball stud.
Wheelarch Height (Unladen*)
INFOID:0000000005260321
Unit: mm (in)
*1: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
Ball joint position
Upper
Lower
Swinging force* (A)
11.4 - 145.5 N (1.16 - 14.8 kg, 2.56 - 32.7 lb)
11.0 - 140.7 N (1.12 - 14.35 kg, 2.47 - 31.63 lb)
Turning torque (B)
0.5 - 6.4 N·m (0.06 - 0.65 kg-m, 5 - 56 in-lb)
0.5 - 6.4 N·m (0.06 - 0.65 kg-m, 5 - 56 in-lb)
Vertical end play (C)
0 mm (0 in)
0 mm (0 in)
Height (D)
44 mm (1.73 in)
45.5 mm (1.79 in)
WEIA0131E
Engine
VQ40DE
VK56DE
Drive type
2WD
4WD
4WD
Tire size
P245/75R16
P265/65R17
P265/60R18
P245/75R16
P265/65R17 P265/60R18 P265/60R18
Front wheelarch height
(Hf)
867
(34.13)
865
(34.06)
—
875
(34.45)
874
(34.41)
—
876 (34.49)
Rear wheelarch height
(Hr)
875
(34.45)
873
(34.37)
—
884
(34.80)
883
(34.76)
—
886 (34.88)
LEIA0085E
2010 Pathfinder
SB-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SB
A
B
SB
N
O
P
CONTENTS
SEAT BELT
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Seat Belt Service . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
ON-VEHICLE REPAIR . . . . . . . . ..
SEAT BELTS . . . . . . . . . . . . . .
Removal and Installation of Front Seat Belt . . . .
Removal and Installation of Rear Seat Belt . . . ..
Removal and Installation of Third Row Seat Belt . .
Seat Belt Inspection . . . . . . . . . . . . ..
LATCH (LOWER ANCHORS AND TETHER
FOR CHILDREN) SYSTEM . . . . . . . ...
Removal and Installation . . . . . . . . . . .
TOP TETHER STRAP CHILD RESTRAINT . .
Removal and Installation . . . . . . . . . . .
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст