Nissan Pathfinder (2010 year). Manual — part 28
AV
PRECAUTIONS
AV-31
< PRECAUTION >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005259261
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000005259262
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
2010 Pathfinder
2010 Pathfinder
AV-32
< PRECAUTION >
[BASE AUDIO]
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
2010 Pathfinder
2010 Pathfinder
AV
PREPARATION
AV-33
< PREPARATION >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000005259263
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0191E
2010 Pathfinder
2010 Pathfinder
AV-34
< ON-VEHICLE REPAIR >
[BASE AUDIO]
AUDIO UNIT
ON-VEHICLE REPAIR
AUDIO UNIT
Removal and Installation
INFOID:0000000005259264
Removal and Installation
REMOVAL
1. Disconnect the battery negative terminal.
2. Remove the cluster lid C. Refer to
IP-12, "Removal and Installation"
.
3. Remove the audio unit screws, using power tool.
4. Remove the audio unit and disconnect audio unit connectors.
5. Remove the audio unit brackets screws and remove the audio unit brackets.
INSTALLATION
1.
Audio unit
2.
Audio unit brackets (LH) and (RH)
3.
Cluster lid C
ALNIA0341ZZ
2010 Pathfinder
2010 Pathfinder
AV
AUDIO UNIT
AV-35
< ON-VEHICLE REPAIR >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Installation is in the reverse order of removal.
2010 Pathfinder
2010 Pathfinder
AV-36
< ON-VEHICLE REPAIR >
[BASE AUDIO]
FRONT TWEETER
FRONT TWEETER
Removal and Installation
INFOID:0000000005259265
REMOVAL
CAUTION:
Use a suitable tool to prevent damage to the front tweeter speaker grille trim and the instrument panel.
1. Remove the front tweeter grille.
2. Remove the front tweeter screws (A).
3. Pull out the front tweeter speaker (1) and disconnect front
tweeter connector, then remove the front tweeter speaker (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0344ZZ
2010 Pathfinder
2010 Pathfinder
AV
FRONT DOOR SPEAKER
AV-37
< ON-VEHICLE REPAIR >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FRONT DOOR SPEAKER
Removal and Installation
INFOID:0000000005259266
REMOVAL
1. Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2. Remove the front door speaker screws (A).
3. Pull out the front door speaker (1), and disconnect the front door
speaker connector and remove the front door speaker (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0347ZZ
2010 Pathfinder
2010 Pathfinder
AV-38
< ON-VEHICLE REPAIR >
[BASE AUDIO]
REAR DOOR SPEAKER
REAR DOOR SPEAKER
Removal and Installation
INFOID:0000000005259267
REMOVAL
1. Remove the rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2. Remove the rear door speaker screws (A).
3. Disconnect the rear door speaker connector (B) and remove
rear door speaker (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0348ZZ
2010 Pathfinder
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст