Nissan Pathfinder (2010 year). Manual — part 493
LUBRICATION SYSTEM
LU-23
< FUNCTION DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
System Chart
INFOID:0000000005260614
PBIC0134E
2010 Pathfinder
LU-24
< ON-VEHICLE MAINTENANCE >
[VK56DE]
ENGINE OIL
ON-VEHICLE MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000005260615
OIL LEVEL
• Before starting the engine make sure the vehicle is parked on a flat
and level surface, then check the oil level. If the engine is already
running, turn it off and allow 10 minutes before checking.
• Pull out oil level gauge and wipe clean.
• Insert oil level gauge.
• Check that the oil level is within the low (L) and high (H) range as
indicated on the dipstick.
• If the engine oil level is out of range, add oil as necessary. Refer to
.
CAUTION:
Do not overfill the engine with oil.
OIL APPEARANCE
• Check the engine oil for a white milky appearance or excessive contamination.
• If the engine oil is milky, it is highly probable that it is contaminated with engine coolant. Repair or replace
damaged parts.
OIL LEAKAGE
Check for oil leakage around the following areas:
• Oil pan
• Oil pan drain plug
• Oil pressure switch
• Oil filter
• Oil cooler
• Intake valve timing control cover
• Intake valve timing control solenoid valve
• Front cover
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head and rocker cover
• Crankshaft oil seal (front and rear)
OIL PRESSURE CHECK
WARNING:
• Be careful not to burn yourself, as the engine and engine oil may be hot.
• Put the A/T shift selector in the Park “P” position.
1. Check the engine oil level. Refer to
.
2. Remove engine front undercover using power tool.
3. Disconnect the oil pressure switch (A) harness connector.
4. Remove the oil pressure switch (A).
CAUTION:
Do not drop or shock oil pressure switch.
SMA954C
WBIA0791E
2010 Pathfinder
ENGINE OIL
LU-25
< ON-VEHICLE MAINTENANCE >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
5. Install Tools.
6. Start the engine and warm it up to normal operating temperature.
7. Check the engine oil pressure with engine running under no-load. Refer to
CAUTION:
If the difference is extreme, check the oil passages and oil pump for leaks and blockages.
8. After the inspections, install oil pressure switch as follows:
a. Remove old liquid gasket adhering to oil pressure switch and engine.
b. Apply liquid gasket and tighten oil pressure switch to the specification.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Prod-
.
c. After warming up engine, make sure there is no leakage of engine oil with engine running.
Changing Engine Oil
INFOID:0000000005260616
WARNING:
• Be careful not to burn yourself, as the engine and engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer; try to avoid direct skin
contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as
possible.
1. Warm up the engine, and check for any oil leaks.
2. Stop the engine and wait for at least 10 minutes.
3. Remove the oil drain plug and oil filler cap to drain the old oil.
4. Install a new washer on the oil drain plug, then install the oil drain plug in the oil pan.
CAUTION:
Clean the drain plug and install with a new washer.
5. Refill the engine with new specified engine oil.
CAUTION:
The refill capacity depends on the oil temperature and drain time. Use the “Refill oil capacity” val-
ues as a reference and check the oil level using the dipstick when filling the engine with oil.
6. Warm up the engine and check the area around the drain plug and oil filter for any oil leaks.
7. Stop the engine and wait for more than 10 minutes.
Tool number
: ST25051001 (J-25695-1)
: ST25052000 (J-25695-2)
WBIA0571E
Oil pressure switch torque
: 14.7 N·m (1.5 kg-m, 11 ft-lb)
Oil drain plug
: Refer to
EM-169, "Removal and Installation"
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
2010 Pathfinder
LU-26
< ON-VEHICLE MAINTENANCE >
[VK56DE]
ENGINE OIL
8. Check the oil level using the dipstick as shown. Add oil as nec-
essary and install the oil filler cap. Refer to
.
CAUTION:
Do not overfill the engine with oil.
SMA954C
2010 Pathfinder
OIL FILTER
LU-27
< ON-VEHICLE MAINTENANCE >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL FILTER
Removal and Installation
INFOID:0000000005260617
REMOVAL
1. Remove the engine front undercover access plate using power tool.
2. Drain engine oil. Refer to
3. Remove the oil filter using Tool as shown.
WARNING:
Be careful not to burn yourself, as the engine and engine oil
may be hot.
CAUTION:
• The oil filter is equipped with a pressure relief valve.
• Use Genuine NISSAN oil filter or equivalent.
• When removing, prepare a shop cloth to absorb any
engine oil leaks or spills.
• Do not allow engine oil to adhere to the drive belts.
• Completely wipe off any engine oil that adheres to the engine and the vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter seal mating surface.
2. Apply clean engine oil to the oil filter seal circumference of the
new oil filter as shown.
3. Screw on the oil filter manually until it touches the installation
surface, then tighten it by 2/3 turn as shown. Or tighten to speci-
fication.
4. Refill engine with new engine oil. Refer to
5. Inspect the engine for oil leaks. Refer to
.
6. Install the engine front undercover access plate using power tool.
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to
2. Start the engine and check for engine oil leaks.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level and add engine oil as required.
Tool number
: KV10115801 (J-38956)
WBIA0388E
SMA010
Oil filter
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA229B
2010 Pathfinder
LU-28
< ON-VEHICLE REPAIR >
[VK56DE]
OIL COOLER
ON-VEHICLE REPAIR
OIL COOLER
Exploded View
INFOID:0000000005260618
Removal and Installation
INFOID:0000000005260619
WARNING:
Be careful not to burn yourself, as the engine oil and engine coolant may be hot.
CAUTION:
• Do not spill engine coolant on the drive belt.
• Do not spill engine oil on rubber parts such as drive belts and engine mounting insulator.
REMOVAL
NOTE:
When removing oil cooler only, step 1 is unnecessary.
1. Drain engine coolant from radiator and cylinder block. Refer to
CO-40, "Changing Engine Coolant"
and
EM-219, "Disassembly and Assembly"
NOTE:
Perform this step only when removing water pipes and hoses.
2. Remove engine front undercover using power tool.
3. Disconnect water hoses from oil cooler, pinching hoses near oil cooler to prevent engine coolant from
spilling.
CAUTION:
Perform this step when engine is cold.
4. Remove oil filter. Refer to
LU-27, "Removal and Installation"
WBIA0790E
1.
Oil pan
2.
Water hose
3.
Water pipe
4.
Water hose
5.
Connector bolt
6.
Oil filter
7.
Oil cooler
8.
O-ring
9.
Relief valve
10. Water hose
11. Connector pipe
12. Gasket
A.
To thermostat housing
B.
Refer to
C.
To cylinder block
2010 Pathfinder
OIL COOLER
LU-29
< ON-VEHICLE REPAIR >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
5. Remove connector bolt, and remove oil cooler.
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing compressed air through engine coolant
inlet. If necessary, replace oil cooler assembly.
Relief Valve
Inspect relief valve for movement, cracks and breaks by pushing the ball. If replacement is necessary, remove
the valve by prying it out using a suitable tool. Install a new valve in place by tapping it in.
INSTALLATION
Installation is in the reverse order of removal, paying attention to the following:
• Confirm that no foreign objects are adhering to the sealing sur-
faces of the oil cooler and oil pan.
• Tighten the connecting bolt after aligning the stopper on the oil pan
side with protrusion of the oil cooler.
INSPECTION AFTER INSTALLATION
1. Check engine oil and engine coolant levels and add engine oil and engine coolant. Refer to
2. Start the engine, and check for leaks of engine oil or engine coolant.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level and engine coolant level again. Refer to
and
KBIA2500E
2010 Pathfinder
LU-30
< ON-VEHICLE REPAIR >
[VK56DE]
OIL PUMP
OIL PUMP
Exploded View
INFOID:0000000005260620
Removal and Installation
INFOID:0000000005260621
REMOVAL
1. Remove the engine assembly from the vehicle. Refer to
EM-214, "Removal and Installation"
.
2. Remove the following components and related parts:
• Drive belt auto tensioner and idler pulley. Refer to
EM-150, "Drive Belt Auto Tensioner and Idler Pulley"
.
• Oil pan (lower), (upper) and oil strainer. Refer to
EM-169, "Removal and Installation"
• Water pump. Refer to
CO-51, "Removal and Installation"
.
3. Remove the Intake valve control solenoid valve cover (RH) (A)
and Intake valve control solenoid valve cover (LH) (B) as fol-
lows:
a. Loosen and remove the bolts in the reverse order as shown.
b. Cut the liquid gasket and remove the covers using Tool.
CAUTION:
Do not damage mating surfaces.
4. Remove the crankshaft pulley.
a. Loosen the crankshaft pulley bolts using a hammer handle to
secure the crankshaft.
WBIA0415E
1.
Oil pump body
2.
Outer rotor
3.
Inner rotor
4.
Oil pump cover
5.
Oil pump drive spacer
6.
Regulator valve
7.
Regulator spring
8.
Regulator plug
Tool number
: KV10111100 (J-37228)
AWBIA0815ZZ
PBIC0053E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст