Nissan Pathfinder (2010 year). Manual — part 177
HOOD
DLK-315
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Removal and Installation of Hood Lock Control
INFOID:0000000005260123
REMOVAL
1. Remove the front grille. Refer to
EXT-18, "Removal and Installation"
2. Remove the front fender protector (LH). Refer to
EXT-23, "Removal and Installation of Front Fender Pro-
3. Disconnect the hood lock cable from the hood lock, and unclip it from the radiator core support upper and
hoodledge.
4. Remove the bolts, and the hood release handle.
5. Separate the grommet from the lower dash panel. Pull the hood lock cable out through the passenger
compartment.
CAUTION:
While pulling, be careful not to damage the outside of the hood lock cable.
INSTALLATION
1. Pull the hood lock cable through the lower dash panel hole into the engine room.
1.
Hood lock assembly
2.
Hood lock cable
WIIA0775E
2010 Pathfinder
DLK-316
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD
Be careful not to bend the cable too much, keep the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the grommet, and push
the grommet into the lower dash panel hole securely.
3. Apply sealant around the grommet at * mark.
4. Install the cable securely to the lock.
5. Adjust the hood lock. Refer to
.
6. Install the front grille. Refer to
EXT-18, "Removal and Installation"
.
Hood Lock Control Inspection
INFOID:0000000005260124
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Remove the front grille. Refer to
EXT-18, "Removal and Installation"
2. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
3. While operating the hood opener, carefully make sure the front
end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
4. Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points shown.
5. Install the front grille. Refer to
EXT-18, "Removal and Installation"
.
LIIA1698E
LIIA1699E
PIIA1086E
PIIA0176E
2010 Pathfinder
DOOR
DLK-317
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR
Fitting Adjustment
INFOID:0000000005260125
Front door
Longitudinal clearance and surface height adjustment at front end
1. Remove the fender. Refer to
EXT-20, "Removal and Installation"
.
2. Loosen the hinge bolts. Raise or lower the front door at rear end to adjust.
3. Install the fender. Refer to
EXT-20, "Removal and Installation"
Rear door
Longitudinal clearance and surface height adjustment at front end
1. Remove the center pillar upper finisher. Refer to
INT-17, "Removal and Installation"
.
2. Loosen the lower hinge bolts.
3. From inside the vehicle, loosen the upper hinge nuts. Open the door, and raise or lower the rear end of the
door to adjust.
4. Install the center pillar lower finisher. Refer to
INT-17, "Removal and Installation"
.
Back door
Longitudinal clearance and surface height adjustment
A.
4.5
±
1.0 mm (0.177
±
0.039 in)
WIIA0732E
2010 Pathfinder
DLK-318
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR
1. Open and support the back door.
2. Slightly loosen the hinge nuts.
3. Reposition the door as necessary and tighten the nuts.
4. Confirm the adjustment. Repeat as necessary to obtain the desired fit.
Striker adjustment
BODY SIDE DOORS
1.
Back door assembly
2.
Back door hinge
3.
Tail lamp assembly
4.
Rear bumper fascia
5.
Roof
6.
Side window glass
a.
7.2
±
2.0 mm (0.28
±
0.06 in)
b.
6.0
±
1.5 mm (0.24
±
0.06 in)
c.
2.0
±
2.0 mm ( 0.08
±
0.08 in)
d.
1.0
±
1.5 mm (0.04
±
0.06 in)
e.
8.0
±
1.5 mm (0.31
±
0.06 in)
f.
5.3
±
2.0 mm (0.21
±
0.08 in)
g.
0.8
±
2.0 mm (0.03
±
0.08 in)
h.
0.8
±
1.0 mm (0.03
±
0.04 in)
j.
2.0
±
1.0 mm (0.08
±
0.04 in)
WIIA0733E
2010 Pathfinder
DOOR
DLK-319
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
BACK DOOR
1. Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
Removal and Installation
INFOID:0000000005260126
FRONT DOOR
CAUTION:
• When removing and installing the door assembly, support the door with a jack and shop cloth to pro-
tect the door and body.
• When removing and installing door assembly, be sure to carry out the fitting adjustment.
• Check the hinge rotating part for poor lubrication. If necessary, apply "body grease".
1. Remove the front door glass and regulator. Refer to
GW-15, "Front Door Glass Regulator"
.
2. Remove the door harness.
3. Remove the check link bolt from the hinge pillar.
4. Remove the door-side hinge nuts, and the door assembly.
Installation is in the reverse order of removal.
WIIA0734E
WIIA0735E
Check link to hinge pillar
bolt
14.7 N·m (1.5 kg-m, 11 ft-lb)
LIIA1726E
Door hinge nuts
24.5 N·m (2.5 kg-m, 18 ft-lb)
LIIA1727E
2010 Pathfinder
DLK-320
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR
REAR DOOR
1. Remove the door finisher. Refer to
INT-14, "Removal and Installation"
.
2. Remove the inner seal.
3. Remove the rear door glass and regulator. Refer to
GW-19, "Rear Door Glass Regulator"
.
4. Remove the door harness.
5. Remove the check link bolt from the hinge pillar.
6. Remove the door-side hinge nuts, and remove the door assembly.
Installation is in the reverse order of removal.
BACK DOOR
1. Remove the glass hatch. Refer to
GW-24, "Removal and Installation"
.
2. Remove the license lamp finisher. Refer to
EXT-21, "Removal and Installation"
.
3. Remove the back door lock assembly. Refer to
DLK-326, "Component Structure"
4. Remove the back door wire harness.
5. Remove the rear washer nozzle and hose from the back door. Refer to
CAUTION:
Two technicians should be used to avoid damaging the back door during removal.
6. Support the back door.
7. Remove the back door stays.
Check link to hinge pillar
bolt
14.7 N·m (1.5 kg-m, 11 ft-lb)
LIIA1726E
Door hinge nuts
24.5 N·m (2.5 kg-m, 18 ft-lb)
LIIA1727E
2010 Pathfinder
DOOR
DLK-321
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8. Remove the door side nuts and the back door assembly.
Installation is in the reverse order of removal.
• Align the back door. Refer to
WIIA1056E
2010 Pathfinder
DLK-322
< ON-VEHICLE REPAIR >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Structure
INFOID:0000000005260127
Removal and Installation
INFOID:0000000005260128
REMOVAL
1. Remove the front door window regulator. Refer to
GW-15, "Front Door Glass Regulator"
2. Remove door side grommet, and remove door key cylinder
assembly (driver side) or outside handle escutcheon (passenger
side) bolts (TORX T30) from grommet hole.
3. While pulling the outside handle (1), remove door key cylinder
assembly or escutcheon (2).
1.
Grommet
2.
Front door striker
3.
Door lock assembly
4.
Outside handle cable
5.
Inside handle assembly
6.
Inside handle cable
7.
Door lock cable
8.
Key cylinder rod (Driver side only)
9.
Door key cylinder
10. Outside handle bracket
11. Front gasket
12. Outside handle
13. Door key cylinder assembly (Driver
side) Outside handle escutcheon
(Passenger side)
14. Rear gasket
⇐
Vehicle front
WIIA0736E
PIIA3553E
ALKIA0956ZZ
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст