Nissan Pathfinder (2010 year). Manual — part 161
PRECAUTIONS
DLK-187
< PRECAUTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
Precaution for work
INFOID:0000000005260001
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
2010 Pathfinder
DLK-188
< PREPARATION >
[WITH INTELLIGENT KEY SYSTEM]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005260002
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairing the cause of noise
—
(J-43241)
Remote Keyless Entry
Tester
Used to test keyfobs
SIIA0993E
SIIA0994E
LEL946A
2010 Pathfinder
PREPARATION
DLK-189
< PREPARATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Commercial Service Tool
INFOID:0000000005260003
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
2010 Pathfinder
DLK-190
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
ON-VEHICLE REPAIR
HOOD
Fitting Adjustment
INFOID:0000000005260004
CLEARANCE AND SURFACE HEIGHT ADJUSTMENT
1. Remove the front grille. Refer to
EXT-18, "Removal and Installation"
2. Loosen the hood lock assembly and adjust the rubber bumpers until the surface height of the hood
becomes 1 mm (0.04 in) lower than the fender.
3. Engage the hood striker and temporarily tighten.
4. Check the lock and striker for looseness.
1.
Hood
2.
Front grille
3.
Front fender
4.
Headlamp assembly
A.
6.0 mm (0.24 in)
B.
0.7 mm (0.03 in)
C.
4.5 mm (0.18 in)
D.
0.0 mm (0.0 in)
E.
6.0 mm (0.24 in)
F.
0.7 mm (0.03 in)
WIIA0774E
2010 Pathfinder
HOOD
DLK-191
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5. Tighten the bolts to specification.
6. Adjust the surface height of the hood according to the fitting standard dimension by rotating right and left
rubber bumpers.
7. Install the front grille. Refer to
EXT-18, "Removal and Installation"
.
HOOD LOCK ADJUSTMENT
1. Remove the front grille. Refer to
EXT-18, "Removal and Installation"
2. Move the hood lock to the left or right so that striker center is vertically aligned with hood lock center
(when viewed from vehicle front).
3. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height or by pressing it lightly approx.
3 kg (29 N, 7lb).
CAUTION:
Do not drop the hood from 300 mm (11.81 in) height or
higher.
4. After adjusting hood lock, tighten the lock bolts to the specified
torque.
5. Install the front grille. Refer to
EXT-18, "Removal and Installation"
.
Removal and Installation of Hood Assembly
INFOID:0000000005260005
1. Support the hood striker with suitable tool to prevent it from falling.
2. Remove the hinge nuts from the hood to remove the hood assembly.
CAUTION:
Operate with two workers, because of its heavy weight.
Installation is in the reverse order of removal.
LIIA1696E
LIIA1701E
WIIA1055E
2010 Pathfinder
DLK-192
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
Removal and Installation of Hood Lock Control
INFOID:0000000005260006
REMOVAL
1. Remove the front grille. Refer to
EXT-18, "Removal and Installation"
2. Remove the front fender protector (LH). Refer to
EXT-23, "Removal and Installation of Front Fender Pro-
3. Disconnect the hood lock cable from the hood lock, and unclip it from the radiator core support upper and
hoodledge.
4. Remove the bolts, and the hood release handle.
5. Separate the grommet from the lower dash panel. Pull the hood lock cable out through the passenger
compartment.
CAUTION:
While pulling, be careful not to damage the outside of the hood lock cable.
INSTALLATION
1. Pull the hood lock cable through the lower dash panel hole into the engine room.
1.
Hood lock assembly
2.
Hood lock cable
WIIA0775E
2010 Pathfinder
HOOD
DLK-193
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Be careful not to bend the cable too much, keep the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the grommet, and push
the grommet into the lower dash panel hole securely.
3. Apply sealant around the grommet at * mark.
4. Install the cable securely to the lock.
5. Adjust the hood lock. Refer to
DLK-192, "Removal and Installa-
6. Install the front grille. Refer to
EXT-18, "Removal and Installation"
.
Hood Lock Control Inspection
INFOID:0000000005260007
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Remove the front grille. Refer to
EXT-18, "Removal and Installation"
2. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
3. While operating the hood opener, carefully make sure the front
end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
4. Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points shown.
5. Install the front grille. Refer to
EXT-18, "Removal and Installation"
.
LIIA1698E
LIIA1699E
PIIA1086E
PIIA0176E
2010 Pathfinder
DLK-194
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
DOOR
DOOR
Fitting Adjustment
INFOID:0000000005260008
Front door
Longitudinal clearance and surface height adjustment at front end
1. Remove the fender. Refer to
EXT-20, "Removal and Installation"
2. Loosen the hinge bolts. Raise or lower the front door at rear end to adjust.
3. Install the fender. Refer to
EXT-20, "Removal and Installation"
Rear door
Longitudinal clearance and surface height adjustment at front end
1. Remove the center pillar upper finisher. Refer to
INT-17, "Removal and Installation"
.
2. Loosen the lower hinge bolts.
3. From inside the vehicle, loosen the upper hinge nuts. Open the door, and raise or lower the rear end of the
door to adjust.
4. Install the center pillar lower finisher. Refer to
INT-17, "Removal and Installation"
.
Back door
Longitudinal clearance and surface height adjustment
A.
4.5
±
1.0 mm (0.177
±
0.039 in)
WIIA0732E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст