Nissan Pathfinder (2010 year). Manual — part 432
FRONT DOOR GLASS AND REGULATOR
GW-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT DOOR GLASS AND REGULATOR
Front Door Glass
INFOID:0000000005259826
REMOVAL
1. Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
4. Operate the power window main switch to raise/lower the door
window until the glass bolts can be seen.
5. Partially remove the inside seal.
6. Remove the glass bolts.
7. While holding the door window, raise it at the rear and pull the
glass out of the sash toward the outside of the door.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass for proper fit. Follow the "FITTING INSPECTION" procedure.
• On the drivers door, reset the motor.
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass and guide rail bolts to correct the glass position.
Front Door Glass Regulator
INFOID:0000000005259827
REMOVAL
1. Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
LIIA1686E
LIIA1687E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
2010 Pathfinder
GW-16
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
4. Operate the power window main switch to raise/lower the door
window until the glass bolts can be seen.
5. Remove the glass bolts.
6. Raise the front door glass and hold it in place with suitable tool
(A) .
7. Disconnect the harness connector from the regulator assembly.
8. Remove the bolts and the regulator assembly.
DISASSEMBLY AND ASSEMBLY
Remove the regulator motor from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Wire wear
• Regulator deformation
LIIA1686E
PIIB3510J
WIIA1033E
2010 Pathfinder
FRONT DOOR GLASS AND REGULATOR
GW-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
• Grease condition for each sliding part
INSTALLATION
1. Install the regulator assembly.
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b. Install the top front regulator bolt.
c. Install the bottom front regulator bolt.
d. Install the bottom rear regulator bolt.
e. Tighten the top rear regulator bolt.
f.
Install the top window motor bolt.
g. Install the lower window motor bolt
h. Install the rear window motor bolt.
2. Connect the harness connector to the regulator assembly.
3. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten glass bolts.
4. Check the glass for proper fit.
5. On the drivers door, reset the motor. Follow the "Setting of Limit Switch" procedure.
6. Reposition the vapor barrier.
WIIA1033E
Regulator and motor bolts : 5.7 N·m (0.58 kg-m, 50 in-lb)
Glass mounting bolts : 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1686E
2010 Pathfinder
GW-18
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
7. Install front door finisher. Refer to
INT-14, "Removal and Installation"
.
SETTING AFTER INSTALLATION
Setting of Limit Switch
If any of the following work has been done, set the limit switch (integrated in the motor).
• Removal and installation of the regulator.
• Removal and installation of the motor from the regulator.
• Removal and installation of the glass.
• Removal and installation of the glass run.
Resetting
After installing each component, perform the following procedure to reset the limit switch.
1. Raise the glass to the top position.
2. While pressing and holding the reset switch, lower the glass to
the bottom position.
3. Release the reset switch. Verify that the reset switch returns to
the original position, if not, pull the switch using suitable tool.
4.
CAUTION:
Do not operate the glass automatically to raise the glass to
the top position.
Raise the glass to the top position.
SIIA0347E
2010 Pathfinder
REAR DOOR GLASS AND REGULATOR
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS AND REGULATOR
Rear Door Glass
INFOID:0000000005259828
REMOVAL
1. Remove the rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
4. Remove the glass run from the partition glass.
5. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
6. Remove the partition sash bolt (lower) and screw (upper) to
remove the sash.
7. Remove the bolts and the glass.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass alignment. Refer to "FITTING INSPECTION".
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass carrier plate bolts to correct the glass position.
Rear Door Glass Regulator
INFOID:0000000005259829
REMOVAL
1. Remove the rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2. Position aside the vapor barrier.
3. Temporarily reconnect the power window switch.
4. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
LIIA1689E
Glass bolts
: 5.7 N·m (0.58 kg-m, 50 in-lb)
LIIA1689E
2010 Pathfinder
GW-20
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
5. Raise the rear door glass and hold it in place with suitable tool
(A).
6. Remove the bolts and the regulator assembly.
• Disconnect the connector from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Gear wear
• Regulator deformation
• Spring damage
• Grease condition for each sliding part
INSTALLATION
PIIB3511J
WIIA1034E
2010 Pathfinder
REAR DOOR GLASS AND REGULATOR
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
1. Connect the harness connector and install the regulator assembly.
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b. Install the top front regulator bolt.
c. Install the bottom regulator bolt.
d. Tighten the top rear regulator bolt.
e. Install the top window motor bolt.
f.
Install the lower window motor bolt.
g. Install the front window motor bolt.
2. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten the bolts.
3. Install the partition sash
4. Check the glass alignment.
5. Reposition the vapor barrier.
6. Install the rear door finisher. Refer to
INT-14, "Removal and Installation"
Regulator assembly
: 7.5 N·m (0.77 kg-m, 66 in-lb)
Glass bolts
: 5.7 N·m (0.58 kg-m, 50 in-lb)
WIIA1034E
LIIA1689E
2010 Pathfinder
GW-22
< REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
SIDE WINDOW GLASS
Removal and Installation
INFOID:0000000005259830
1.
Glass
2.
Primer area
3.
Body side outer
4.
Rear door assembly
5.
Back door assembly
6.
Locating clips
7.
Urethane
a.
15 mm (0.59 in)
b.
42.5 mm (1.67 in)
WIIA1035E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст