Nissan Pathfinder (2010 year). Manual — part 302
EC-508
< BASIC INSPECTION >
[VK56DE]
INSPECTION AND ADJUSTMENT
OK
>> GO TO 10.
NG
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the following.
• Check camshaft position sensor (PHASE) and circuit. Refer to
EC-700, "DTC Confirmation Procedure"
• Check crankshaft position sensor (POS) and circuit. Refer to
EC-696, "DTC Confirmation Procedure"
.
OK or NG
OK
>> GO TO 9.
NG
>> 1. Repair or replace malfunctioning part.
2. GO TO 4.
9.
CHECK ECM FUNCTION
1. Substitute with a non-malfunctioning ECM to check ECM function. (ECM may be the cause of the incident,
but this is rare.)
2. Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
SEC-10, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement"
system),
SEC-124, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement"
(without
intelligent key system).
>> GO TO 4.
10.
CHECK IGNITION TIMING
1. Run engine at idle.
2. Check ignition timing with a timing light.
EC-510, "Idle Speed and Ignition Timing Check"
OK or NG
OK
>> GO TO 19.
NG
>> GO TO 11.
11.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1. Stop engine.
2. Perform
EC-511, "Accelerator Pedal Released Position Learning"
.
>> GO TO 12.
12.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform
EC-511, "Throttle Valve Closed Position Learning"
.
>> GO TO 13.
13.
PERFORM IDLE AIR VOLUME LEARNING
EC-511, "Idle Air Volume Learning"
.
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes
>> GO TO 14.
No
>> 1. Follow the instructions of Idle Air Volume Learning.
2. GO TO 4.
14.
CHECK TARGET IDLE SPEED AGAIN
With CONSULT-III
1. Start engine and warm it up to normal operating temperature.
15
±
5
°
BTDC (in P or N position)
BBIA0379E
2010 Pathfinder
INSPECTION AND ADJUSTMENT
EC-509
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2. Read idle speed in “DATA MONITOR” mode with CONSULT-III.
EC-510, "Idle Speed and Ignition Timing Check"
Without CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.
EC-510, "Idle Speed and Ignition Timing Check"
OK or NG
OK
>> GO TO 15.
NG
>> GO TO 17.
15.
CHECK IGNITION TIMING AGAIN
1. Run engine at idle.
2. Check ignition timing with a timing light.
EC-510, "Idle Speed and Ignition Timing Check"
OK or NG
OK
>> GO TO 19.
NG
>> GO TO 16.
16.
CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Refer to
EM-181, "Removal and Installation"
OK or NG
OK
>> GO TO 17.
NG
>> 1. Repair the timing chain installation.
2. GO TO 4.
17.
DETECT MALFUNCTIONING PART
Check the following.
• Check camshaft position sensor (PHASE) and circuit. Refer to
EC-700, "DTC Confirmation Procedure"
• Check crankshaft position sensor (POS) and circuit. Refer to
EC-696, "DTC Confirmation Procedure"
.
OK or NG
OK
>> GO TO 18.
NG
>> 1. Repair or replace.
2. GO TO 4.
18.
CHECK ECM FUNCTION
1. Substitute with a non-malfunctioning ECM to check ECM function. (ECM may be the cause of the incident,
although this is rare.)
2. Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
SEC-10, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement"
(with intelligent key
system),
SEC-124, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement"
(without
intelligent key system).
>> GO TO 4.
19.
INSPECTION END
If ECM is replaced during this Basic Inspection procedure, perform
EC-510, "Procedure After Replacing
650
±
50 rpm (in P or N position)
650
±
50 rpm (in P or N position)
15
±
5
°
BTDC (in P or N position)
BBIA0379E
2010 Pathfinder
EC-510
< BASIC INSPECTION >
[VK56DE]
INSPECTION AND ADJUSTMENT
>> INSPECTION END
Idle Speed and Ignition Timing Check
INFOID:0000000005257491
IDLE SPEED
With CONSULT-III
Check idle speed in “DATA MONITOR” mode with CONSULT-III.
With GST
Check idle speed with GST.
IGNITION TIMING
1. Attach timing light to loop wire as shown.
2. Check ignition timing.
Procedure After Replacing ECM
INFOID:0000000005257492
When replacing ECM, the following procedure must be performed.
1. Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs.
SEC-10, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement"
(with intelli-
gent key system),
SEC-124, "ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement"
(without intelligent key system).
2. Perform
3. Perform
EC-511, "Accelerator Pedal Released Position Learning"
.
4. Perform
EC-511, "Throttle Valve Closed Position Learning"
5. Perform
EC-511, "Idle Air Volume Learning"
.
VIN Registration
INFOID:0000000005257493
DESCRIPTION
VIN Registration is a function of ECM to register VIN in ECM. It must be performed each time ECM is
replaced.
NOTE:
Accurate VIN which is registered in ECM may be required for Inspection & Maintenance (I/M).
OPERATION PROCEDURE
BBIA0377E
BBIA0379E
2010 Pathfinder
INSPECTION AND ADJUSTMENT
EC-511
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
With CONSULT-III
1. Check the VIN of the vehicle and note it. Refer to
GI-21, "Identification Number"
.
2. Turn ignition switch ON with engine stopped.
3. Select “VIN REGISTRATION” in “WORK SUPPORT” mode.
4. Follow the instructions on the CONSULT-III display.
Accelerator Pedal Released Position Learning
INFOID:0000000005257494
DESCRIPTION
Accelerator Pedal Released Position Learning is a function of ECM to learn the fully released position of the
accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each
time the harness connector of the accelerator pedal position sensor or ECM is disconnected.
OPERATION PROCEDURE
1. Check that accelerator pedal is fully released.
2. Turn ignition switch ON and wait at least 2 seconds.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON and wait at least 2 seconds.
5. Turn ignition switch OFF and wait at least 10 seconds.
Throttle Valve Closed Position Learning
INFOID:0000000005257495
DESCRIPTION
Throttle Valve Closed Position Learning is a function of ECM to learn the fully closed position of the throttle
valve by monitoring the throttle position sensor output signal. It must be performed each time the harness con-
nector of the electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1. Check that accelerator pedal is fully released.
2. Turn ignition switch ON.
3. Turn ignition switch OFF wait at least 10 seconds.
heck that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume Learning
INFOID:0000000005257496
DESCRIPTION
Idle Air Volume Learning is a function of ECM to learn the idle air volume that keeps engine idle speed within
the specific range. It must be performed under the following conditions:
• Each time the electric throttle control actuator or ECM is replaced.
• Idle speed or ignition timing is out of the specification.
PREPARATION
Before performing Idle Air Volume Learning, check that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
• Battery voltage: More than 12.9V (At idle)
• Engine coolant temperature: 70 - 100
°
C (158 - 212
°
F)
• Selector lever position: P or N
• Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime light systems, if the parking brake is applied before the engine is
started the headlamp will not be illuminated.
• Steering wheel: Neutral (Straight-ahead position)
• Vehicle speed: Stopped
• Transmission: Warmed-up
- With CONSULT-III: Drive vehicle until “ATF TEMP SE 1” in “DATA MONITOR” mode of “A/T” system indi-
cates less than 0.9 V.
- Without CONSULT-III: Drive vehicle for 10 minutes.
OPERATION PROCEDURE
2010 Pathfinder
EC-512
< BASIC INSPECTION >
[VK56DE]
INSPECTION AND ADJUSTMENT
With CONSULT-III
1. Perform
EC-511, "Accelerator Pedal Released Position Learning"
.
2. Perform
EC-511, "Throttle Valve Closed Position Learning"
3. Start engine and warm it up to normal operating temperature.
4. Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
5. Select “IDLE AIR VOL LEARN” in “WORK SUPPORT” mode.
6. Touch “START” and wait 20 seconds.
7. Check that “CMPLT” is displayed on CONSULT-III screen. If “CMPLT” is not displayed, Idle Air Volume
Learning will not be carried out successfully. In this case, find the cause of the incident by referring to the
DIAGNOSTIC PROCEDURE below.
8. Rev up engine 2 or 3 times and check that idle speed and ignition timing are within the specifications.
Without CONSULT-III
NOTE:
•
It is better to count the time accurately with a clock.
•
It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has
a malfunction.
1. Perform
EC-511, "Accelerator Pedal Released Position Learning"
.
2. Perform
EC-511, "Throttle Valve Closed Position Learning"
3. Start engine and warm it up to normal operating temperature.
4. Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
5. Turn ignition switch OFF and wait at least 10 seconds.
6. Check that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
7. Repeat the following procedure quickly 5 times within 5 seconds.
a. Fully depress the accelerator pedal.
b. Fully release the accelerator pedal.
8. Wait 7 seconds, fully depress the accelerator pedal for approximately 20 seconds until the MIL stops
blinking and turns ON.
9. Fully release the accelerator pedal within 3 seconds after the MIL turns ON.
10. Start engine and let it idle.
11. Wait 20 seconds.
12. Rev up engine 2 or 3 times and check that idle speed and ignition timing are within the specifications.
ITEM
SPECIFICATION
Idle speed
650
±
50 rpm (in P or N position)
Ignition timing
15
±
5
°
BTDC (in P or N position)
ITEM
SPECIFICATION
Idle speed
650
±
50 rpm (in P or N position)
Ignition timing
15
±
5
°
BTDC (in P or N position)
SEC897C
2010 Pathfinder
INSPECTION AND ADJUSTMENT
EC-513
< BASIC INSPECTION >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
13. If idle speed and ignition timing are not within the specifications, Idle Air Volume Learning will not be car-
ried out successfully. In this case, find the cause of the incident by referring to the DIAGNOSTIC PROCE-
DURE below.
DIAGNOSTIC PROCEDURE
If idle air volume learning cannot be performed successfully, proceed as per the following:
1.
Check that throttle valve is fully closed.
2.
Check PCV valve operation.
3.
Check that downstream of throttle valve is free from air leakage.
4.
When the above three items check out OK, engine component parts and their installation condi-
tion are questionable. Check and eliminate the cause of the incident.
It is useful to perform
EC-566, "Inspection Procedure"
.
5.
If any of the following conditions occur after the engine has started, eliminate the cause of the
incident and perform Idle Air Volume Learning again:
•
Engine stalls.
•
Erroneous idle.
2010 Pathfinder
EC-514
< FUNCTION DIAGNOSIS >
[VK56DE]
ENGINE CONTROL SYSTEM
FUNCTION DIAGNOSIS
ENGINE CONTROL SYSTEM
System Diagram
INFOID:0000000005257497
JMBIA1925GB
2010 Pathfinder
ENGINE CONTROL SYSTEM
EC-515
< FUNCTION DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Engine Control Component Parts Location
INFOID:0000000005257498
1.
ECM
2.
Battery current sensor
3.
Refrigerant pressure sensor
4.
Power steering pressure sensor
5.
Intake valve timing control solenoid
valve (bank 2)
6.
Cooling fan motor
7.
Intake valve timing control position
sensor (bank 2)
8.
Engine coolant temperature sensor
9.
Electric throttle control actuator
10. Intake valve timing control position
sensor (bank 1)
11. Intake valve timing control solenoid
valve (bank 1)
12. Camshaft position sensor (PHASE)
13. Mass air flow sensor (with intake air
temperature sensor)
14. A/F sensor 1 (bank 1)
15. Ignition coil (with power transistor)
and spark plug (bank 1)
16. EVAP service port
17. Fuel injector (bank 1)
18. Knock sensor (bank 1)
19. EVAP canister purge volume control
solenoid valve
20. Knock sensor (bank 2)
21. Fuel injector (bank 2)
22. Ignition coil (with power transistor)
and spark plug (bank 2)
23. A/F sensor 1 (bank 2)
24. IPDM E/R
ALBIA0352ZZ
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст