Nissan Pathfinder (2010 year). Manual — part 287
EC-388
< COMPONENT DIAGNOSIS >
[VQ40DE]
P2A00, P2A03 A/F SENSOR 1
2. Check voltage between A/F sensor 1 terminal 4 and ground with
CONSULT-III or tester.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E2, F32
• IPDM E/R connector E119
• 15 A fuse (No.51)
• Harness for open or short between A/F sensor 1 and fuse
>> Repair or replace harness or connectors.
8.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between A/F sensor 1 terminal and ECM terminal as follows.
Refer to Wiring Diagram.
4. Check harness continuity between the following terminals and ground.
Refer to Wiring Diagram.
5. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 9.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK A/F SENSOR 1 HEATER
EC-108, "Component Inspection"
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 11.
Voltage: Battery voltage
PBIB3308E
A/F sensor 1 terminal
ECM terminal
Bank1
1
16
2
75
Bank 2
1
35
2
56
Continuity should exist.
Bank 1
Bank 2
A/F sensor 1 terminal
ECM terminal
A/F sensor 1 terminal
ECM terminal
1
16
1
35
2
75
2
56
Continuity should not exist.
2010 Pathfinder
P2A00, P2A03 A/F SENSOR 1
EC-389
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
10.
CHECK INTERMITTENT INCIDENT
Perform
GI-37, "Intermittent Incident"
.
OK or NG
OK
>> GO TO 11.
NG
>> Repair or replace.
11.
REPLACE A/F SENSOR 1
Replace malfunctioning A/F sensor 1.
CAUTION:
• Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
• Before installing new A/F sensor, clean exhaust system threads using Heated Oxygen Sensor
Thread Cleaner tool J-43897-18 or J-43897-12 and approved anti-seize lubricant.
>> GO TO 12.
12.
CONFIRM A/F ADJUSTMENT DATA
1. Turn ignition switch ON.
2. Select “A/F ADJ-B1” and “A/F ADJ-B2” in “DATA MONITOR” mode with CONSULT-III.
3. Make sure that “0” is displayed on CONSULT-III screen.
OK or NG
OK
>>
INSPECTION END
NG
>> GO TO 13.
13.
CREAR A/F ADJUSTMENT DATA
With CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Select “SELF-LEARNING CONT” in “WORK SUPPORT” mode with CONSULT-III.
3. Clear the self-learning control coefficient by touching “CLEAR”.
Without CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF.
3. Disconnect mass air flow sensor harness connector.
4. Restart engine and let it idle for at least 5 seconds.
5. Stop engine and reconnect mass air flow sensor harness con-
nector.
6. Make sure DTC P0102 is displayed.
7. Erase the DTC memory. Refer to
8. Make sure DTC P0000 is displayed.
>> GO TO 14.
14.
CONFIRM A/F ADJUSTMENT DATA
1. Turn ignition switch OFF and then ON.
2. Select “A/F ADJ-B1” and “A/F ADJ-B2” in “DATA MONITOR” mode with CONSULT-III.
3. Make sure that “0” is displayed on CONSULT-III screen.
OK or NG
OK
>>
INSPECTION END
BBIA0541E
2010 Pathfinder
EC-390
< COMPONENT DIAGNOSIS >
[VQ40DE]
ASCD BRAKE SWITCH
ASCD BRAKE SWITCH
Component Description
INFOID:0000000005257428
When the brake pedal is depressed, ASCD brake switch is turned
OFF and stop lamp switch is turned ON. ECM detects the state of
the brake pedal by two types of input (ON/OFF signal).
for the ASCD function.
Diagnosis Procedure
INFOID:0000000005257429
1.
CHECK OVERALL FUNCTION-I
With CONSULT-III
1. Turn ignition switch ON.
2. Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT-III.
3. Check “BRAKE SW1” indication under the following conditions.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check voltage between ECM terminal 108 and ground under the
following conditions.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 3.
2.
CHECK OVERALL FUNCTION-II
With CONSULT-III
Check “BRAKE SW2” indication in “DATA MONITOR” mode.
Without CONSULT-III
Check voltage between ECM terminal 101 and ground under the following conditions.
BBIA0560E
CONDITION
INDICATION
When brake pedal: Slightly depressed
OFF
When brake pedal: Fully released
ON
CONDITION
VOLTAGE
When brake pedal: Slightly depressed
Approximately 0V
When brake pedal: Fully released
Battery voltage
MBIB0061E
CONDITION
INDICATION
When brake pedal: Fully released
OFF
When brake pedal: Slightly depressed
ON
2010 Pathfinder
ASCD BRAKE SWITCH
EC-391
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK or NG
OK
>>
INSPECTION END
NG
>> GO TO 7.
3.
CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ASCD brake switch harness connector.
3. Turn ignition switch ON.
4. Check voltage between ASCD brake switch terminal 1 and
ground with CONSULT-III or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Fuse block (J/B) connector E160
• 10A fuse
• Harness for open or short between ASCD brake switch and fuse
>> Repair open circuit or short to ground in harness or connectors.
5.
CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between ECM terminal 108 and ASCD brake switch terminal 2.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
CONDITION
VOLTAGE
When brake pedal: Fully released
Approximately 0V
When brake pedal: Slightly depressed
Battery voltage
MBIB0060E
BBIA0560E
Voltage: Battery voltage
PBIB0857E
Continuity should exist.
2010 Pathfinder
EC-392
< COMPONENT DIAGNOSIS >
[VQ40DE]
ASCD BRAKE SWITCH
OK or NG
OK
>> GO TO 6.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK ASCD BRAKE SWITCH
EC-393, "Component Inspection"
OK or NG
OK
>> GO TO 11.
NG
>> Replace ASCD brake switch.
7.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check voltage between stop lamp switch terminal 1 and ground
with CONSULT -II or tester.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the following.
• Fuse block (J/B) connector E160
• 10A fuse
• Harness for open or short between stop lamp switch and battery
>> Repair open circuit or short to ground or short to power in harness or connectors.
9.
CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect ECM harness connector.
2. Check harness continuity between ECM terminal 101 and stop lamp switch terminal 2.
Refer to Wiring Diagram.
3. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 10.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
10.
CHECK STOP LAMP SWITCH
EC-393, "Component Inspection"
BBIA0560E
Voltage: Battery voltage
PBIB1184E
Continuity should exist.
2010 Pathfinder
ASCD BRAKE SWITCH
EC-393
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK or NG
OK
>> GO TO 11.
NG
>> Replace stop lamp switch.
11.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
.
>>
INSPECTION END
Component Inspection
INFOID:0000000005257430
ASCD BRAKE SWITCH
1. Turn ignition switch OFF.
2. Disconnect ASCD brake switch harness connector.
3. Check harness continuity between ASCD brake switch terminals
1 and 2 under the following conditions.
If NG, adjust ASCD brake switch installation, refer to
"Inspection and Adjustment - Standard Pedal"
or
"Inspection and Adjustment - Adjustable Pedal"
and perform
step 3 again.
STOP LAMP SWITCH
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check harness continuity between stop lamp switch terminals 1
and 2 under the following conditions.
If NG, adjust stop lamp switch installation, refer to
"Inspection and Adjustment - Standard Pedal"
or
"Inspection and Adjustment - Adjustable Pedal"
, and perform
step 3 again.
Condition
Continuity
When brake pedal: Fully released.
Should exist.
When brake pedal: Slightly depressed.
Should not exist.
SEC023D
Condition
Continuity
When brake pedal: Fully released.
Should not exist.
When brake pedal: Slightly depressed.
Should exist.
PBIB1185E
2010 Pathfinder
EC-394
< COMPONENT DIAGNOSIS >
[VQ40DE]
ASCD INDICATOR
ASCD INDICATOR
Component Description
INFOID:0000000005257431
ASCD indicator lamp illuminates to indicate ASCD operation status. Lamp has two indicators, CRUISE and
SET, and is integrated in combination meter.
CRUISE indicator illuminates when MAIN switch on ASCD steering switch is turned ON to indicated that
ASCD system is ready for operation.
SET indicator illuminates when the following conditions are met.
• CRUISE indicator is illuminated.
• SET/COAST switch on ASCD steering switch is turned ON while vehicle speed is within the range of the
ASCD setting.
SET indicator remains lit during ASCD control.
for the ASCD function.
Diagnosis Procedure
INFOID:0000000005257432
1.
CHECK OVERALL FUNCTION
Check ASCD indicator under the following conditions.
OK or NG
OK
>>
INSPECTION END
NG
>> GO TO 2.
2.
CHECK DTC
Check that DTC UXXXX is not displayed.
OK or NG
OK
>> GO TO 3.
NG
>> Perform trouble diagnoses for DTC UXXXX.
3.
CHECK COMBINATION METER FUNCTION
.
OK or NG
OK
>> GO TO 4.
NG
>> Go to .
4.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
>>
INSPECTION END
ASCD INDICATOR
CONDITION
SPECIFICATION
CRUISE LAMP
• Ignition switch: ON
MAIN switch: pressed at the 1st time
→
at the 2nd time
ON
→
OFF
SET LAMP
• MAIN switch: ON
• When vehicle speed is be-
tween 40 km/h (25 MPH) and
144 km/h (89 MPH)
ASCD: Operating
ON
ASCD: Not operating
OFF
2010 Pathfinder
COOLING FAN
EC-395
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
COOLING FAN
Description
INFOID:0000000005257433
COMPONENT DESCRIPTION
Cooling Fan Motor
The cooling fan operates at each speed when the current flows in the cooling fan motor as follows.
Diagnosis Procedure
INFOID:0000000005257434
1.
CHECK IPDM E/R GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connectors E122, E124.
3. Check harness continuity between IPDM E/R terminals 38, 59 and ground.
Refer to Wiring Diagram.
4. Also check harness for short to power.
OK or NG
OK
>> GO TO 2.
NG
>> Repair open circuit or short to power in harness or connectors.
2.
CHECK COOLING FAN MOTOR CIRCUIT FOR OPEN AND SHORT
1. Disconnect cooling fan motor harness connector.
2. Check harness continuity between the following;
cooling fan motor terminal 1 and IPDM E/R terminal 20,
cooling fan motor terminal 2 and IPDM E/R terminal 24.
Refer to Wiring Diagram.
3. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK COOLING FAN MOTER GROUND CIRCUIT FOR OPEN OR SHORT
1. Check harness continuity between the following;
cooling fan motor terminal 3 and ground,
cooling fan motor terminal 4 and ground.
Refer to Wiring Diagram.
2. Also check harness for short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to power in harness or connectors.
Cooling fan speed
Cooling fan motor terminals
(+)
(
−
)
Low (LOW)
1
3 and 4
2
3 and 4
High (HI)
1 and 2
3 and 4
Continuity should exist.
Continuity should exist.
BBIA0555E
Continuity should exist.
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст