Nissan Pathfinder (2010 year). Manual — part 409
EXL-138
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000005259781
AUTO LIGHT SYSTEM
The auto light system may not turn the headlamp ON/OFF immediately after passing a dark area or a bright
area (short tunnel, sky bridge, shadowed area etc.). This is normal.
2010 Pathfinder
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
EXL-139
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM
Description
INFOID:0000000005259782
The headlamps (both sides) do not switch to high beam when the lighting switch is in the HI or PASS setting.
Diagnosis Procedure
INFOID:0000000005259783
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
.
Is the combination switch normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "HL HI REQ" of IPDM E/R DATA MONITOR item.
2. With operating the lighting switch, check the monitor status.
Is the monitor item status normal?
YES
>> GO TO 3
NO
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
3.
HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to
Is the headlamp (HI) circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-33, "Removal and Installation of IPDM E/R"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
ON
Except for HI or
PASS
OFF
2010 Pathfinder
EXL-140
< SYMPTOM DIAGNOSIS >
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000005259784
The headlamps (both sides) do not turn ON in any lighting switch setting.
Diagnosis Procedure
INFOID:0000000005259785
1.
CHECK COMBINATION SWITCH
Check the combination switch. Refer to
.
Is the combination switch normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "HL LO REQ" of IPDM E/R DATA MONITOR item.
2. With operating the lighting switch, check the monitor status.
Is the monitor item status normal?
YES
>> GO TO 3
NO
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
3.
HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to
.
Is the headlamp (LO) circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-33, "Removal and Installation of IPDM E/R"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
ON
OFF
OFF
2010 Pathfinder
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
EXL-141
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
Description
INFOID:0000000005259786
The parking, license plate and tail lamps do not turn ON in with any lighting switch setting.
Diagnosis Procedure
INFOID:0000000005259787
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
.
Is the combination switch normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "TAIL&CLR REQ" of IPDM E/R DATA MONITOR item.
2. With operating the lighting switch, check the monitor status.
Is the monitor item status normal?
YES
>> GO TO 3
NO
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
3.
PARK LAMP CIRCUIT INSPECTION
Check the parking lamp circuit. Refer to
Is the tail lamp circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-33, "Removal and Installation of IPDM E/R"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
TAIL&CLR REQ
Lighting switch
1ST
ON
OFF
OFF
2010 Pathfinder
EXL-142
< SYMPTOM DIAGNOSIS >
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000005259788
The front fog lamps do not turn ON in any setting.
Diagnosis Procedure
INFOID:0000000005259789
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
.
Is the combination switch normal?
YES
>> GO TO 2
NO
>> Repair or replace the malfunctioning part.
2.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "FR FOG REQ" of IPDM E/R DATA MONITOR item.
2. With operating the front fog lamp switch, check the monitor status.
Is the monitor item status normal?
YES
>> GO TO 3
NO
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
3.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
.
Is the front fog lamp circuit normal?
YES
>> Replace IPDM E/R. Refer to
PCS-33, "Removal and Installation of IPDM E/R"
.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(Lighting switch 2ND)
ON
ON
OFF
OFF
2010 Pathfinder
PRECAUTIONS
EXL-143
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005503163
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000005550749
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
2010 Pathfinder
EXL-144
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
2010 Pathfinder
ADJUSTMENT AND INSPECTION
EXL-145
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
ON-VEHICLE REPAIR
ADJUSTMENT AND INSPECTION
HEADLAMP
HEADLAMP : Aiming Adjustment
INFOID:0000000005259791
For details, refer to the regulations in your area.
NOTE:
If vehicle front body has been repaired and /or the headlamp assembly has been replaced, check headlamp
aiming.
• Before performing aiming adjustment, check the following:
- Confirm headlamp aiming switch is set to "0" (zero) position.
- Ensure all tires are inflated to correct pressure.
- Place vehicle and screen on level surface.
- Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant and engine oil filled to correct level, and fuel tank full.
- Confirm spare tire, jack and tools are properly stowed.
- Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
- Use adjusting screw to perform aiming adjustment
LOW BEAM AND HIGH BEAM
LKIA0568E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст