Nissan Pathfinder (2010 year). Manual — part 500
CHASSIS AND BODY MAINTENANCE
MA-43
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Remove the filler plug and gasket.
2. Fill the transfer with new fluid until the fluid level reaches the
specified limit near the filler plug hole.
CAUTION:
Carefully fill fluid. (Fill up for approx. 3 minutes.)
3. Leave the vehicle for 3 minutes, and check fluid level again.
4. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
TRANSFER FLUID : TX15B
INFOID:0000000005255699
TRANSFER FLUID : Inspection
INFOID:0000000005255700
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
FLUID LEAKAGE AND FLUID LEVEL
1. Make sure that fluid is not leaking from the transfer assembly or around it.
2. Check fluid level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking fluid level.
3. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
TRANSFER FLUID : Replacement
INFOID:0000000005255701
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
DRAINING
1. Stop engine.
2. Remove the drain plug and gasket and drain the fluid.
3. Install the drain plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug and gasket.
Fluid grade and capacity : Refer to
SDIA3209E
SDIA3287E
SDIA3286E
2010 Pathfinder
MA-44
< ON-VEHICLE MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
2. Fill the transfer with new fluid until the fluid level reaches the
specified limit near the filler plug hole.
CAUTION:
Carefully fill fluid. (Fill up for approx. 3 minutes.)
3. Leave the vehicle for 3 minutes, and check fluid level again.
4. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
PROPELLER SHAFT
PROPELLER SHAFT : Checking Propeller Shaft
INFOID:0000000005255702
Check the front and rear propeller shafts for damage, dents, and cracks. Check the joints for looseness and
any damage. Repair or replace as necessary. Refer to
DLN-203, "NVH Troubleshooting Chart"
.
DIFFERENTIAL GEAR OIL
DIFFERENTIAL GEAR OIL : Front Final Drive R180T
INFOID:0000000005255703
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000005255704
DIFFERENTIAL GEAR OIL LEAKAGE AND LEVEL
1. Make sure that differential gear oil is not leaking from the front final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with a new gasket on it to the front final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000005255705
DRAINING
1. Stop the engine.
2. Remove the drain plug and gasket from the front final drive
assembly to drain the differential gear oil.
3. Install the drain plug with a new gasket to the front final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
FILLING
Fluid grade and capacity : Refer to
SDIA3287E
LDIA0176E
LDIA0175E
2010 Pathfinder
CHASSIS AND BODY MAINTENANCE
MA-45
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Remove the filler plug and gasket from the front final drive
assembly.
2. Fill the front final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with a new gasket on it to the front final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Front Final Drive M205
INFOID:0000000005255706
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000005255707
DIFFERENTIAL GEAR OIL LEAKAGE AND LEVEL
1. Make sure that differential gear oil is not leaking from the front final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with sealant applied on the threads to the
front final drive assembly. Tighten to the specified torque. Refer
DLN-390, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Products and Sealants"
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000005255708
DRAINING
1. Stop the engine.
2. Remove the drain plug from the front final drive assembly to drain the differential gear oil.
3. Install the drain plug with sealant applied on the threads to the front final drive assembly. Tighten to the
specified torque. Refer to
DLN-390, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Prod-
FILLING
1. Remove the filler plug from the front final drive assembly.
2. Fill the front final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with sealant applied on the threads to the
front final drive assembly. Tighten to the specified torque. Refer
DLN-390, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Products and Sealants"
Differential gear oil
grade and capacity
: Refer to
LDIA0176E
LDIA0176E
Differential gear oil
grade and capacity
: Refer to
LDIA0176E
2010 Pathfinder
MA-46
< ON-VEHICLE MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
DIFFERENTIAL GEAR OIL : Rear Final Drive R200
INFOID:0000000005255709
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000005255710
OIL LEAKAGE AND OIL LEVEL
1. Make sure that differential gear oil is not leaking from the rear final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000005255711
DRAINING
1. Stop the engine.
2. Remove the drain plug and gasket from the rear final drive
assembly to drain the differential gear oil.
3. Install the drain plug with a new gasket to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug and gasket from the rear final drive ass-
mebly.
2. Fill the rear final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Rear Final Drive R230
INFOID:0000000005255712
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000005255713
OIL LEAKAGE AND OIL LEVEL
1. Make sure that differential gear oil is not leaking from the rear final drive assembly or around it.
LDIA0163E
LDIA0162E
Differential gear oil
grade and capacity
: Refer to
LDIA0163E
2010 Pathfinder
CHASSIS AND BODY MAINTENANCE
MA-47
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000005255714
DRAINING
1. Stop the engine.
2. Remove the drain plug and gasket from the rear final drive
assembly to drain the differential gear oil.
3. Install the drain plug with a new gasket to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug and gasket from the rear final drive
assembly.
2. Fill the rear final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
WHEELS
WHEELS : Balancing Wheels
INFOID:0000000005255715
WHEEL BALANCE REMOVAL
1. Remove wheel and tire using power tool.
2. Using releasing agent, remove double-faced adhesive tape from the wheel.
CAUTION:
• Be careful not to scratch the wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the wheel.
WHEEL BALANCE INSTALLATION AND ADJUSTMENT
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for wheels.
1. Set wheel on wheel balancer using the center hole as a guide. Start the tire balance machine.
LLIA0068E
LLIA0068E
Differential gear oil
grade and capacity
: Refer to
LLIA0068E
2010 Pathfinder
MA-48
< ON-VEHICLE MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
2. When inner and outer imbalance values are shown on the wheel balancer indicator, multiply outer imbal-
ance value by 1.6 to determine balance weight that should be used. Select the outer balance weight with
a value closest to the calculated value and install it to the designated outer position of, or at the desig-
nated angle in relation to the road wheel.
CAUTION:
• Do not install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, be sure to clean the mating surface of the wheel.
Indicated imbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz) = 40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4 g = 35 g (1.23 oz)
37.5 g = 40 g (1.41 oz)
a. Install balance weight in the position shown.
b. When installing balance weight to wheels, set it into the grooved
area on the inner wall of the wheel as shown so that the balance
weight center is aligned with the wheel balancer indication posi-
tion (angle).
CAUTION:
• Always use Genuine NISSAN adhesion balance weights.
• Balance weights are not reusable; always replace with
new ones.
• Do not install more than three sheets of balance weights.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top of another.
3. Start wheel balancer again.
4. Install drive-in balance weight on inner side of road wheel in the
wheel balancer indication position (angle).
CAUTION:
Do not install more than two balance weights.
5. Start wheel balancer. Make sure that inner and outer residual
imbalance values are 5 g (0.18 oz) each or below.
• If either residual imbalance value exceeds 5 g (0.18 oz),
repeat installation procedures.
SMA054D
WDIA0060E
SMA056D
2010 Pathfinder
CHASSIS AND BODY MAINTENANCE
MA-49
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Wheel Balance (Maximum Allowable Imbalance)
WHEELS : Rotation
INFOID:0000000005255716
NOTE:
Follow the maintenance schedule for tire rotation service intervals. Refer to
1. Remove wheels and tires.
2. Rotate wheels and tires on each side from front to back as
shown. Do not include the spare wheel and tire when rotating
the wheels and tires.
CAUTION:
When installing wheels and tires, tighten them diagonally
by dividing the work two to three times in order to prevent
the wheels from developing any distortion.
3. Adjust the tire pressure to specification. Refer to
.
4. After the wheel and tire rotation, retighten the wheel nuts after
the vehicle has been driven for 1,000 km (600 miles), and also after any wheel and tire has been installed,
such as after repairing a flat tire.
BRAKE FLUID LEVEL AND LEAKS
BRAKE FLUID LEVEL AND LEAKS : Checking Brake Fluid Level and Leaks
INFOID:0000000005255717
• Check the brake fluid level in the reservoir tank. It should be
between the “MAX” and “MIN” lines on the reservoir tank.
• Visually check around reservoir tank for fluid leaks.
• If the fluid level is extremely low, check the brake system.
• If the brake warning lamp comes on when the fluid is at the correct
level, check the brake fluid level switch and the parking brake
switch.
BRAKE LINES AND CABLES
BRAKE LINES AND CABLES : Checking Brake Line and Cables
INFOID:0000000005255718
1. Check the brake lines and hoses for cracks, deterioration, and
other damage. Replace any damaged parts.
CAUTION:
If brake fluid leaks are visible around the brake line joints,
retighten the joint, or replace damaged parts as necessary.
2. Check for brake fluid leaks by fully depressing brake pedal while
engine is running.
DISC BRAKE
Maximum allowable imbalance
Dynamic (at rim flange)
5 g (0.18 oz) (one side)
Static
10 g (0.35 oz)
Wheel nut
: 133 N·m (14 kg-m, 98 ft-lb)
SMA829C
LFIA0234E
SBR389C
2010 Pathfinder
MA-50
< ON-VEHICLE MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
DISC BRAKE : Checking Disc Brake
INFOID:0000000005255719
ROTOR
Check the condition of the rotor, and for any wear or damage. Repair
or replace as necessary.
CALIPER
Check for any fluid leakage. Repair as necessary.
PAD
Inspect the thickness of pad through cylinder body inspection hole.
Use a scale for inspection if necessary.
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Checking Steering Gear and Linkage
INFOID:0000000005255720
STEERING GEAR
• Check the steering gear housing for looseness, damage and oil
leakage as shown.
• Check the steering column connections for looseness.
STEERING LINKAGE
Standard thickness
: Refer to
Repair limit thickness
SBR020B
SMA922A
Standard thickness
: Refer to
Repair limit thickness
: Refer to
BRA0010D
SGIA0506E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст