Murano Cross Cabriolet Z51 (2012 year). Manual — part 92
SRC-112
< DTC/CIRCUIT DIAGNOSIS >
B1136 SIDE AIR BAG MODULE LH
B1136 SIDE AIR BAG MODULE LH
DTC Logic
INFOID:0000000007564681
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-112, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564682
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE SIDE AIR BAG MODULE
1.
Replace side air bag module LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1136
SIDE MODULE LH
[GND-SHORT]
Side air bag module LH circuit is shorted to
ground
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1136 SIDE AIR BAG MODULE LH
SRC-113
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-114
< DTC/CIRCUIT DIAGNOSIS >
B1137 SIDE AIR BAG MODULE LH
B1137 SIDE AIR BAG MODULE LH
DTC Logic
INFOID:0000000007564683
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-114, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564684
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE SIDE AIR BAG MODULE
1.
Replace side air bag module LH. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1137
SIDE MODULE LH
[SHORT]
Side air bag module LH circuits are shorted
to each other
• Harness or connectors
(The module circuit is shorted.)
• Malfunction in side air bag module LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1137 SIDE AIR BAG MODULE LH
SRC-115
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-116
< DTC/CIRCUIT DIAGNOSIS >
B1138, B1139, B1140, B1141, B1142, B1143 DIAGNOSIS SENSOR UNIT
B1138, B1139, B1140, B1141, B1142, B1143 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007564685
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-116, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564686
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1138
B1139
B1140
B1141
B1142
B1143
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1144 DIAGNOSIS SENSOR UNIT
SRC-117
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1144 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007564687
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-117, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564688
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of CON-
SULT
DTC detecting condition
Possible cause
B1144
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
or out of the specification
• Malfunction in air bag diagnosis sensor unit
• Configuration in air bag diagnosis sensor unit
does not match the vehicles specification
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-118
< DTC/CIRCUIT DIAGNOSIS >
B1154, B1155, B1156, B1157, B1158, B1159 DIAGNOSIS SENSOR UNIT
B1154, B1155, B1156, B1157, B1158, B1159 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007564689
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-118, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564690
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1154
B1155
B1156
B1157
B1158
B1159
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT
SRC-119
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007564691
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-119, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564692
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1170
B1171
B1172
B1173
B1174
B1175
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-120
< DTC/CIRCUIT DIAGNOSIS >
B1186, B1187, B1188, B1189, B1190, B1191 DIAGNOSIS SENSOR UNIT
B1186, B1187, B1188, B1189, B1190, B1191 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007564693
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-120, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564694
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1186
B1187
B1188
B1189
B1190
B1191
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
B1202, B1203, B1204, B1205, B1206, B1207 DIAGNOSIS SENSOR UNIT
SRC-121
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1202, B1203, B1204, B1205, B1206, B1207 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000007564695
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-121, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564696
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1202
B1203
B1204
B1205
B1206
B1207
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-122
< DTC/CIRCUIT DIAGNOSIS >
B1209 FRONTAL COLLISION DETECTION
B1209 FRONTAL COLLISION DETECTION
Description
INFOID:0000000007564697
The air bags and seat belt pre-tensioners for driver and passenger are activated by the air bag diagnosis sen-
sor unit signal transmitted at the time of the frontal collision.
DTC Logic
INFOID:0000000007564698
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-122, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564699
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis.Refer to
SR-5, "FOR FRONTAL COLLISION : When SRS is activated in a colli-
SR-6, "FOR FRONTAL COLLISION : When SRS is not activated in a collision"
.
>> GO TO 2.
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis of applicable DTC.Refer to
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1209
FRONTAL COLLI-
SION DETECTION
Seat belt pre-tensioner, driver side air bag and passen-
ger air bag are deployed
—
Revision: 2013 February
2012 Murano CrossCabriolet
B1210 SIDE COLLISION DETECTION
SRC-123
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1210 SIDE COLLISION DETECTION
Description
INFOID:0000000007564700
The side air bag and curtain air bag are activated by the air bag diagnosis sensor unit signal transmitted at the
time of side collision.
DTC Logic
INFOID:0000000007564701
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-123, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564702
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis.Refer to
SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is activated
or
SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision"
>> GO TO 2.
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis of applicable DTC.Refer to
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1210
SIDE COLLISION
DETECTION
Side air bag and curtain air bag are deployed
—
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-124
< DTC/CIRCUIT DIAGNOSIS >
B1211 ROLLOVER DETECTION
B1211 ROLLOVER DETECTION
Description
INFOID:0000000007564703
The seat belt pre-tensioner, door-mounted curtain air bag and pop-up roll bar are activated by the air bag diag-
nosis sensor unit signal at the time of rollover.
DTC Logic
INFOID:0000000007564704
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-124, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564705
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis.Refer to
SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is activated
SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision"
.
>> GO TO 2.
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Peform diagnosis of applicable DTC.Refer to
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1211
ROLLOVER DETECTION
Seat belt pre-tensioner and curtain air bag module are
deployed because of rollover detection
—
Revision: 2013 February
2012 Murano CrossCabriolet
B1212, B1213, B1214 SATELLITE SENSOR RH
SRC-125
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1212, B1213, B1214 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000007564706
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-125, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564707
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor RH. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1212
B1213
B1214
RH1 SAT-SENS
Satellite sensor RH is malfunctioning
• Harness or connectors
• Malfunction in satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
SRC-126
< DTC/CIRCUIT DIAGNOSIS >
B1212, B1213, B1214 SATELLITE SENSOR RH
NO
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
B1215, B1216, B1217 SATELLITE SENSOR LH
SRC-127
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1215, B1216, B1217 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000007564708
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-13, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-127, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007564709
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace satellite sensor LH. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1215
B1216
B1217
LH1 SAT-SENS
Satellite sensor LH is malfunctioning
• Harness or connectors
• Malfunction in satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст