Murano Cross Cabriolet Z51 (2012 year). Manual — part 73
PWC-58
< SYMPTOM DIAGNOSIS >
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES NORMAL-
LY
REAR LH : Diagnosis Procedure
INFOID:0000000007563183
1.
CHECK ENCODER (REAR LH) CIRCUIT
Check encoder (rear LH) circuit.
Refer to
PWC-39, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE REAR POWER WINDOW SWITCH LH
1.
Replace rear power window switch LH. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
REAR RH
REAR RH : Diagnosis Procedure
INFOID:0000000007563184
1.
CHECK ENCODER (REAR RH) CIRCUIT
Check encoder (rear RH) circuit.
Refer to
PWC-41, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE REAR POWER WINDOW SWITCH RH
1.
Replace rear power window switch RH. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2013 February
2012 Murano CrossCabriolet
ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY
PWC-59
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY
Diagnosis Procedure
INFOID:0000000007563185
1.
CHECK POWER WINDOW AUTO OPERATION
Check AUTO operation when anti-pinch function does not operate.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-57, "DRIVER SIDE : Diagnosis Procedure"
(driver side),
(passenger side).
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 February
2012 Murano CrossCabriolet
PWC-60
< SYMPTOM DIAGNOSIS >
AUTOMATIC WINDOW ADJUSTING FUNCTION DOES NOT OPERATE
AUTOMATIC WINDOW ADJUSTING FUNCTION DOES NOT OPERATE
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000007563186
1.
CHECK AUTO UP OPERATION
Check AUTO operation when automatic window adjusting function does not operate.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-57, "DRIVER SIDE : Diagnosis Procedure"
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check front door switch (driver side).
Refer to
PWC-50, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE POWER WINDOW MAIN SWITCH
1.
Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000007563187
1.
CHECK AUTO UP OPERATION
Check AUTO operation when automatic window adjusting function does not operate.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
PWC-57, "PASSENGER SIDE : Diagnosis Procedure"
.
2.
CHECK FRONT DOOR SWITCH (PASSENGER SIDE)
Check front door switch (passenger side).
Refer to
PWC-50, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
1.
Replace front power window switch (passenger side). Refer to
PWC-66, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2013 February
2012 Murano CrossCabriolet
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE
PROPERLY
PWC-61
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
ATE PROPERLY
Diagnosis Procedure
INFOID:0000000007563188
1.
CHECK FRONT DOOR SWITCH
Check front door switch.
Refer to
DLK-55, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-76, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2013 February
2012 Murano CrossCabriolet
PWC-62
< SYMPTOM DIAGNOSIS >
DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WINDOWS
DOOR KEY CYLINDER SWITCH DOES NOT OPERATE POWER WIN-
DOWS
Diagnosis Procedure
INFOID:0000000007563189
1.
PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE) (DOOR KEY CYLINDER SWITCH)
Check front door lock assembly (driver side) (door key cylinder switch).
Refer to
PWC-44, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE POWER WINDOW MAIN SWITCH
1.
Replace power window main switch. Refer to
PWC-66, "Removal and Installation"
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2013 February
2012 Murano CrossCabriolet
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
PWC-63
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000007563190
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Refer to
DLK-20, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
2.
CHECK POWER WINDOW OPERATION
Check power window operation.
Does power window up/down with power window main switch?
YES
>> GO TO 3.
NO
>> Refer to
.
3.
CHECK “PW DOWN SET” SETTING IN “WORK SUPPORT”
Check “PW DOWN SET” setting in “WORK SUPPORT”.
Refer to
DLK-35, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “PW DOWN SET” setting in “WORK SUPPORT”.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-76, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Revision: 2013 February
2012 Murano CrossCabriolet
PWC-64
< SYMPTOM DIAGNOSIS >
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis Procedure
INFOID:0000000007563191
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE
PWC-65
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW SWITCH ILLUMINATION DOES NOT ILLUMINATE
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000007563192
1.
REPLACE POWER WINDOW MAIN SWITCH
Replace power window main switch.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000007563193
1.
REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Replace front power window switch (passenger side).
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
REAR LH
REAR LH : Diagnosis Procedure
INFOID:0000000007563194
1.
REPLACE REAR POWER WINDOW SWITCH LH
Replace rear power window switch LH.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
REAR RH
REAR RH : Diagnosis Procedure
INFOID:0000000007563195
1.
REPLACE REAR POWER WINDOW SWITCH RH
Replace rear power window switch RH.
Refer to
PWC-66, "Removal and Installation"
.
>> INSPECTION END
Revision: 2013 February
2012 Murano CrossCabriolet
PWC-66
< REMOVAL AND INSTALLATION >
POWER WINDOW MAIN SWITCH
REMOVAL AND INSTALLATION
POWER WINDOW MAIN SWITCH
Exploded View
INFOID:0000000007563196
Removal and Installation
INFOID:0000000007563197
REMOVAL
1.
Remove the power window main switch finisher. Refer to
13, "Removal and Installation"
.
2.
Power window main switch (1) is removed from power window
main switch finisher (2) using remover tool (A).
NOTE:
The same procedure is also performed for front power window
switch (passenger side) and rear power window switch (LH & RH).
INSTALLATION
Install in the reverse order of removal.
NOTE:
If power window main switch or front power window switch (passenger side) is replaced or removed, it is nec-
essary to perform initialization procedure. Refer to
.
1.
Power window main switch
2.
Power window main switch finisher
JMKIA1823ZZ
JMKIA1822ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Precaution for Battery Service . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . ...
POWER SOCKET . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .....
REMOVAL AND INSTALLATION . . . .
POWER SOCKET . . . . . . . . . . . ..
FRONT POWER SOCKET . . . . . . . . . . ..
FRONT POWER SOCKET : Exploded View . . ....
FRONT POWER SOCKET : Removal and Instal-
lation . . . . . . . . . . . . . . . . . . .
CONSOLE POWER SOCKET . . . . . . . . ....
CONSOLE POWER SOCKET : Exploded View . ...
CONSOLE POWER SOCKET : Removal and In-
stallation . . . . . . . . . . . . . . . . ...
Revision: 2013 February
2012 Murano CrossCabriolet
PWO-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007566432
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000007566433
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Precaution for Battery Service
INFOID:0000000007566434
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Revision: 2013 February
2012 Murano CrossCabriolet
PWO
POWER SOCKET
PWO-3
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
WIRING DIAGRAM
POWER SOCKET
Wiring Diagram
INFOID:0000000007566435
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JRMWC5439GB
Revision: 2013 February
2012 Murano CrossCabriolet
PWO-4
< REMOVAL AND INSTALLATION >
POWER SOCKET
REMOVAL AND INSTALLATION
POWER SOCKET
FRONT POWER SOCKET
FRONT POWER SOCKET : Exploded View
INFOID:0000000007566436
FRONT POWER SOCKET : Removal and Installation
INFOID:0000000007566437
REMOVAL
1.
Remove front console pocket. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (B) from the
inner socket hole (square) (C).
4.
Remove ring (2) from front console pocket while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and front console pocket.
CONSOLE POWER SOCKET
CONSOLE POWER SOCKET : Exploded View
INFOID:0000000007566438
CONSOLE POWER SOCKET : Removal and Installation
INFOID:0000000007566439
REMOVAL
1
: Inner socket
2
: Ring
JPMIA0782ZZ
D
: Cut out
JPMIA0783ZZ
1
: Inner socket
2
: Ring
JSMIA0522ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
PWO
POWER SOCKET
PWO-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
1.
Remove console finisher assembly. Refer to
.
2.
Disconnect power socket connector (A).
3.
Pull out inner socket (1) by pushing the ring pawl (C) from the
inner socket hole (square) (D).
4.
Remove ring (2) from console box while pressing pawls.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Align the cut outs of inner socket, ring, and console box.
B
: Hole for power socket
(Console box)
E
: Cut out
JSMIA0233ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
RAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
N
O
P
CONTENTS
REAR AXLE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Drive Shaft . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR WHEEL HUB AND HOUSING . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REAR DRIVE SHAFT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR WHEEL HUB AND HOUSING . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
REAR DRIVE SHAFT . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Disassembly and Assembly . . ...
FINAL DRIVE SIDE . . . . . . . . . . . . .
FINAL DRIVE SIDE : Disassembly and Assembly .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Revision: 2013 February
2012 Murano CrossCabriolet
RAX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Drive Shaft
INFOID:0000000007564329
• Observe the following precautions when disassembling and assembling drive shaft.
• Never disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts, before disassembling and assembling.
• Prevent the entry of foreign objects during disassembly of the service location.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
• Use paper waste. Do not use fabric shop cloths because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст