Murano Cross Cabriolet Z51 (2012 year). Manual — part 105
WCS
BCM (BODY CONTROL MODULE)
WCS-25
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BCM (BODY CONTROL MODULE)
List of ECU Reference
INFOID:0000000007565182
ECU
Reference
BCM
BCS-53, "DTC Inspection Priority Chart"
Revision: 2013 February
2012 Murano CrossCabriolet
WCS-26
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
WIRING DIAGRAM
WARNING CHIME SYSTEM
Wiring Diagram
INFOID:0000000007565183
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JRNWC1241GB
Revision: 2013 February
2012 Murano CrossCabriolet
WCS
DIAGNOSIS AND REPAIR WORKFLOW
WCS-27
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000007565184
OVERALL SEQUENCE
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.
CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.
CHECK CONSULT SELF-DIAGNOSIS RESULTS
1.
Connect CONSULT and perform self-diagnosis. Refer to
.
2.
When DTC is detected, follow the instructions below:
-
Record DTC and Freeze Frame Data.
Are self-diagnosis results normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
JSNIA4492GB
Revision: 2013 February
2012 Murano CrossCabriolet
WCS-28
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
4.
NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
>> GO TO 5.
5.
REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: 2013 February
2012 Murano CrossCabriolet
WCS
POWER SUPPLY AND GROUND CIRCUIT
WCS-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
INFOID:0000000007710087
1.
CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check harness between combination meter and fuse.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Check continuity between combination meter harness connector terminals and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Power source
Fuse No.
Battery
11
Ignition switch ON or START
4
Terminals
Ignition switch po-
sition
Voltage
(Approx.)
(+)
(-)
Combination meter
Ground
Connector
Terminal
M34
1
OFF
Battery voltage
2
ON
Terminals
Continuity
(+)
(-)
Combination meter
Ground
Connector
Terminal
M34
3
Existed
4
23
Revision: 2013 February
2012 Murano CrossCabriolet
WCS-30
< DTC/CIRCUIT DIAGNOSIS >
METER BUZZER CIRCUIT
METER BUZZER CIRCUIT
Description
INFOID:0000000007565186
• The buzzer for warning chime system is installed in the combination meter.
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check
INFOID:0000000007565187
1.
CHECK OPERATION OF METER BUZZER
1.
Select “BUZZER” of “BCM” on CONSULT.
2.
Perform “LIGHT WARN ALM” of “Active Test”.
Does meter buzzer beep?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
Diagnosis Procedure
INFOID:0000000007565188
1.
CHECK POWER SUPPLY OF COMBINATION METER
Check power supply of combination meter. Refer to
MWI-47, "COMBINATION METER : Diagnosis Proce-
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair power supply circuit of combination meter. Refer to
BUZZER
Under the condition of buzzer input
: On
Except above
: Off
Revision: 2013 February
2012 Murano CrossCabriolet
WCS
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
WCS-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
Description
INFOID:0000000007565189
Transmits a seat belt buckle switch signal (driver side) to the combination meter.
Component Function Check
INFOID:0000000007565190
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value.
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000007565191
1.
CHECK COMBINATION METER INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between combination meter harness connector terminal and ground.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and seat belt buckle switch (driver side) connector.
3.
Check continuity between combination meter harness connector terminal and seat belt buckle switch
(driver side) harness connector terminal.
4.
Check harness continuity between combination meter harness connector terminal and ground.
Is the inspection result normal?
BUCKLE SW
When seat belt is fastened
: Off
When seat belt is unfastened
: On
Terminals
Condition
Voltage
(Approx.)
(+)
(-)
Combination meter
Ground
Connector
Terminal
M34
35
When seat belt is fastened
12 V
When seat belt is unfastened
0 V
Terminals
Continuity
(+)
(-)
Combination meter
Seat belt buckle switch(driver side)
Connector
Terminal
Connector
Terminal
M34
35
B449
40
Exist
Terminals
Continuity
(+)
(-)
Combination meter
Ground
Connector
Terminal
M34
35
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
WCS-32
< DTC/CIRCUIT DIAGNOSIS >
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK SEAT BELT BUCKLE SWITCH GROUND CIRCUIT
Check harness continuity between seat belt buckle switch (driver side) harness connector terminal and
ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000007565192
1.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect the seat belt buckle switch (driver side) connector.
3.
Check continuity between terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the seat belt buckle. Refer to
SB-7, "SEAT BELT BUCKLE : Removal and Installation"
Terminals
Continuity
(+)
(-)
Combination meter
Ground
Connector
Terminal
B449
41
Exist
Terminals
Condition
Continuity
(+)
(-)
Seat belt buckle switch (driver side)
Connector
Terminal
Connector
Terminal
B449
40
B449
41
When seat belt is fastened
Not existed
When seat belt is unfastened
Exist
Revision: 2013 February
2012 Murano CrossCabriolet
WCS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
WCS-33
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000007565193
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure
INFOID:0000000007565194
1.
CHECK PARKING BRAKE WARNING LAMP
1.
Start the engine.
2.
Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-70, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform a check for the parking brake switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to
MWI-56, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-70, "Removal and Installation"
.
NO
>> Replace the parking brake switch. Refer to
When parking brake is applied
: ON
When parking brake is released
: OFF
Revision: 2013 February
2012 Murano CrossCabriolet
WCS-34
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000007565195
Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure
INFOID:0000000007565196
1.
CHECK COMBINATION SWITCH (LIGHT SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch (light switch).
Do they operate normally?
YES
>> GO TO 2.
NO
>> Refer to
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL CIRCUIT
Perform the check for the front door switch (driver side) signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Perform a unit check for the front door switch (driver side). Refer to
DLK-56, "Component Inspection"
.
Is the inspection result normal?
YES
BCS-76, "Removal and Installation"
NO
>> Replace the front door switch (driver side). Refer to
DLK-171, "Removal and Installation"
.
Revision: 2013 February
2012 Murano CrossCabriolet
WCS
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
WCS-35
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
Description
INFOID:0000000007565197
• Seat belt reminder warning does not sound.
• Seat belt reminder warning sounds continuously.
Diagnosis Procedure
INFOID:0000000007565198
1.
CHECK SEAT BELT WARNING LAMP
1.
Turn ignition switch ON.
2.
Check the operation of the seat belt warning lamp in the combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK BCM OUTPUT SIGNAL
Check if the light reminder warning chime is activated by performing BCM active test. Refer to
"BUZZER : CONSULT Function (BCM - BUZZER)"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-70, "Removal and Installation"
.
NO
>> Replace the BCM. Refer to
BCS-76, "Removal and Installation"
4.
CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
Perform the check for the seat belt buckle switch circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to
WCS-32, "Component Inspection"
Is the inspection result normal?
YES
>> Replace the combination meter. Refer to
MWI-70, "Removal and Installation"
.
NO
>> Replace the seat belt buckle. Refer to
SB-7, "SEAT BELT BUCKLE : Removal and Installation"
.
Seat belt fastened
: OFF
Seat belt not fastened
: ON
Buzzer active condition
: On
Buzzer non-active condition
: Off
Revision: 2013 February
2012 Murano CrossCabriolet
WCS-36
< SYMPTOM DIAGNOSIS >
THE KEY WARNING DOES NOT SOUND
THE KEY WARNING DOES NOT SOUND
Description
INFOID:0000000007565199
The is key warning chime does not sound under the following conditions.
• Key inserted into the key slot. (Key slot switch ON)
• Ignition switch is not in ON or START. (Ignition switch signal OFF)
• Front door switch (driver side) is open. [Door switch signal (driver side) ON]
Diagnosis Procedure
INFOID:0000000007565200
1.
CHECK BCM INPUT SIGNAL
1.
Connect CONSULT.
2.
Select the “Data Monitor” of “BCM (BUZZER)” and check the “KEY SW-SLOT” monitor value. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK KEY SLOT SWITCH SIGNAL CIRCUIT
Check the key slot switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check applicable parts, and repair or replace corresponding parts.
3.
CHECK DOOR SWITCH SIGNAL (DRIVER SIDE) CIRCUIT
Check the door switch signal (driver side) circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check the front door switch (driver side). Refer to
DLK-56, "Component Inspection"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
NO
>> Replace front door switch (driver side). Refer to
DLK-171, "Removal and Installation"
.
Revision: 2013 February
2012 Murano CrossCabriolet
WT-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
WT
A
B
WT
N
O
P
CONTENTS
ROAD WHEELS & TIRES
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . ..
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Service Notice and Precautions for TPMS . . . ....
Service Notice and Precautions for Road Wheel ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
BCM . . . . . . . . . . . . . . . . . . ..
Tire Pressure Sensor . . . . . . . . . . . ....
Tire Pressure Receiver . . . . . . . . . . .....
Information Display . . . . . . . . . . . . ...
SYSTEM . . . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
AIR PRESSURE MONITOR . . . . . . . . . ..
AIR PRESSURE MONITOR : CONSULT Function
(BCM - AIR PRESSURE MONITOR) . . . . . ..
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . ...
List of ECU Reference . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
TIRE PRESSURE MONITORING SYSTEM . ..
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
BCM . . . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
TIRE PRESSURE SENSOR WAKE UP OP-
ERATION . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
ID REGISTRATION . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
C1704, C1705, C1706, C1707 LOW TIRE
PRESSURE . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1708, C1709, C1710, C1711 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1716, C1717, C1718, C1719 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
Revision: 2013 February
2012 Murano CrossCabriolet
WT-2
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1729 VEHICLE SPEED SIGNAL . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1734 BCM . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
TIRE PRESSURE RECEIVER . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
TPMS . . . . . . . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN ON . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN OFF . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
BLINKS . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
ID REGISTRATION CANNOT BE COMPLET-
ED . . . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . .
PERIODIC MAINTENANCE . . . . . ...
ROAD WHEEL . . . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
Wheel Balance Adjustment . . . . . . . . . .
Tire Rotation . . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ..
ROAD WHEEL TIRE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
How to Handle Puncture Repair Agent . . . . ...
TIRE PRESSURE SENSOR . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
TIRE PRESSURE RECEIVER . . . . . . ...
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Road Wheel . . . . . . . . . . . . . . .
Tire Air Pressure . . . . . . . . . . . . . .
Revision: 2013 February
2012 Murano CrossCabriolet
PRECAUTIONS
WT-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007565857
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000007565858
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000007565859
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Service Notice and Precautions for TPMS
INFOID:0000000007565860
• Low tire pressure warning lamp blinks for 1min, then turns ON when occurring any malfunction except low
tire pressure. Delete the memory with CONSULT, or register the ID to turn low tire pressure warning lamp
Revision: 2013 February
2012 Murano CrossCabriolet
WT-4
< PRECAUTION >
PRECAUTIONS
OFF. Refer to
WT-10, "AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
• ID registration is required when replacing or rotating wheels, replacing tire pressure sensor or BCM. Refer to
• Replace grommet seal, valve core and cap of tire pressure sensor in TPMS every tire replacement by reach-
ing wear limit of tire. Refer to
Service Notice and Precautions for Road Wheel
INFOID:0000000007565861
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Never apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст