Murano Cross Cabriolet Z51 (2012 year). Manual — part 64
MWI-58
< DTC/CIRCUIT DIAGNOSIS >
WASHER LEVEL SWITCH SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace washer level switch. Refer to
WW-35, "Removal and Installation"
.
Terminals
Condition
Continuity
Washer level switch
1
2
Washer level switch ON
Existed
Washer level switch OFF
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT
MWI-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT
Description
INFOID:0000000007565130
A/C auto amp. transmit the A/C auto amp. connection recognition signal to the combination meter.
Diagnosis Procedure
INFOID:0000000007565131
1.
CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between combination meter harness connector terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and A/C auto amp. connector.
3.
Check continuity between combination meter harness connector terminal and A/C auto amp. harness
connector terminal.
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Terminals
Voltage
(Approx.)
(+)
(-)
Combination meter
Ground
Connector
Terminal
M34
19
5 V
Combination meter
A/C auto amp.
Continuity
Connector
Terminal
Connector
terminal
M34
19
M50
34
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
19
Not existed
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-60
< SYMPTOM DIAGNOSIS >
THE FUEL GAUGE POINTER DOES NOT MOVE
SYMPTOM DIAGNOSIS
THE FUEL GAUGE POINTER DOES NOT MOVE
Description
INFOID:0000000007565132
Fuel gauge needle will not move from a certain position.
Diagnosis Procedure
INFOID:0000000007565133
1.
CONDUCTING THE COMBINATION METER SELF-DIAGNOSIS MODE
Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally.
Refer to
MWI-20, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the combination meter.
2.
CHECK FLOAT INTERFERENCE
Check that the float arm interferes with or binds to other components in the fuel tank.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check the fuel level sensor signal circuit. Refer to
MWI-48, "Component Function Check"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
THE METER CONTROL SWITCH IS INOPERATIVE
MWI-61
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE METER CONTROL SWITCH IS INOPERATIVE
Description
INFOID:0000000007565134
If any of the following malfunctions is found for the meter control switch operation.
• All switches are inoperative.
• The specified switch cannot be operated.
Diagnosis Procedure
INFOID:0000000007565135
1.
CHECK METER CONTROL SWITCH SIGNAL CIRCUIT
Check the meter control switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK METER CONTROL SWITCH
Perform a unit check for the meter control switch. Refer to
MWI-52, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NG
>> Replace meter control switch. Refer to
MWI-72, "Removal and Installation"
.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-62
< SYMPTOM DIAGNOSIS >
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000007565136
The oil pressure warning lamp stays off when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000007565137
1.
CHECK OIL PRESSURE WARNING LAMP
Perform auto active test. Refer to
PCS-10, "Diagnosis Description"
Is oil pressure warning lamp blinking?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OIL PRESSURE SWITCH SIGNAL CIRCUIT
Check the oil pressure switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK OIL PRESSURE SWITCH
Perform a unit check for the oil pressure switch. Refer to
MWI-54, "Component Inspection"
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO
>> Replace oil pressure switch. Refer to
EM-38, "Removal and Installation"
.
4.
CHECK COMBINATION METER INPUT SIGNAL
Connect CONSULT and perform an input signal check for the combination meter. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
MWI-63
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000007565138
The oil pressure warning lamp remains illuminated while the engine is running (normal oil pressure).
Diagnosis Procedure
INFOID:0000000007565139
1.
CHECK OIL PRESSURE WARNING LAMP
Perform auto active test. Refer to
PCS-10, "Diagnosis Description"
Is oil pressure warning lamp blinking?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
CHECK IPDM E/R OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect the oil pressure switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between the oil pressure switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
CHECK OIL PRESSURE SWITCH
Perform a unit check for the oil pressure switch. Refer to
MWI-54, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Replace oil pressure switch. Refer to
EM-38, "Removal and Installation"
.
4.
CHECK OIL PRESSURE SWITCH SIGNAL CIRCUIT
Check the oil pressure switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK COMBINATION METER INPUT SIGNAL
Connect CONSULT and perform an input signal check for the combination meter. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
Terminals
Voltage
(Approx.)
(+)
(
−
)
Oil pressure switch
Ground
Connector
Terminal
F63
1
12 V
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-64
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING,
OR DOES NOT DISPLAY
Description
INFOID:0000000007565140
• The parking brake warning is displayed during vehicle travel even though the parking brake is released.
• The parking brake warning is not displayed even though driving the vehicle with the parking brake applied.
Diagnosis Procedure
INFOID:0000000007565141
1.
CHECK PARKING BRAKE WARNING LAMP OPERATION
1.
Start engine.
2.
Check the operation of the parking brake warning lamp when operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Check the parking brake switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to
MWI-56, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace parking brake switch. Refer to
.
Condition
Warning lamp status
When parking brake is applied
ON
When parking brake is released
OFF
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR DOES
NOT DISPLAY
MWI-65
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LOW WASHER FLUID WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
Description
INFOID:0000000007565142
• The warning is still displayed even after washer fluid is added.
• The warning is not displayed even though the washer tank is empty.
Diagnosis Procedure
INFOID:0000000007565143
1.
CHECK WASHER LEVEL SWITCH SIGNAL CIRCUIT
Check the washer level switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK WASHER LEVEL SWITCH
Perform a unit check for the washer level switch. Refer to
MWI-57, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace washer level switch. Refer to
WW-35, "Removal and Installation"
.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-66
< SYMPTOM DIAGNOSIS >
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
THE DOOR OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT
DISPLAY
Description
INFOID:0000000007565144
• The door ajar warning is displayed even though all of the doors are closed.
• The door ajar warning is not displayed even though a door is ajar.
Diagnosis Procedure
INFOID:0000000007565145
1.
CHECK BCM INPUT/OUTPUT SIGNAL
Connect CONSULT and check the BCM input signals. Refer to
DLK-55, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “DOOR W/L” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
3.
CHECK DOOR SWITCH SIGNAL CIRCUIT
Check the door switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK DOOR SWITCH
Perform a unit check for the door switch. Refer to
DLK-56, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace applicable door switch. Refer to
DLK-171, "Removal and Installation"
“DOOR W/L”
Door open
: On
Door closed
: Off
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
THE TRUNK OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
MWI-67
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE TRUNK OPEN WARNING CONTINUES DISPLAYING, OR DOES NOT
DISPLAY
Description
INFOID:0000000007565146
• The trunk ajar warning is displayed continuously even though the trunk lid is closed.
• The trunk ajar warning is not displayed even though the trunk lid is open.
Diagnosis Procedure
INFOID:0000000007565147
1.
CHECK BCM INPUT SIGNAL
1.
Connect the CONSULT.
2.
Check the BCM input signals. Refer to
DLK-69, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “TRUNK/GLAS-H” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
3.
CHECK TRUNK ROOM LAMP SWITCH SIGNAL CIRCUIT
Check the trunk room lamp switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK TRUNK ROOM LAMP SWITCH
Check the room lamp switch. Refer to
DLK-70, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace trunk lid lock assembly. Refer to
DLK-165, "Removal and Installation"
.
“TRUNK/GLAS-H”
Trunk lid open
: On
Trunk lid closed
: Off
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-68
< SYMPTOM DIAGNOSIS >
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
Description
INFOID:0000000007565148
• The displayed ambient air temperature is higher than the actual temperature.
• The displayed ambient air temperature is lower than the actual temperature.
Diagnosis Procedure
INFOID:0000000007565149
NOTE:
Check that the symptom is not applicable to the normal operating condition before starting diagnosis. Refer to
MWI-69, "INFORMATION DISPLAY : Description"
.
1.
CHECK AMBIENT SENSOR SIGNAL CIRCUIT
Check the ambient sensor signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL CIRCUIT
Check the A/C auto amp. connection recognition signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK AMBIENT SENSOR
Perform a unit check for the ambient sensor. Refer to
HAC-41, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-70, "Removal and Installation"
NO
>> Replace ambient sensor. Refer to
HAC-79, "Removal and Installation"
.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
NORMAL OPERATING CONDITION
MWI-69
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NORMAL OPERATING CONDITION
COMPASS
COMPASS : Description
INFOID:0000000007565150
COMPASS
• The electronic compass is highly protected from changes in most magnetic fields. However, some large
changes in magnetic fields can affect it. Some examples are (but not limited to): high tension power lines,
large steel buildings, subways, steel bridges, automatic car washes, large piles of scrap metal, etc. While
this does not happen very often, it is possible.
• During normal operation, the compass mirror will continuously update the compass calibration to adjust for
gradual changes in the vehicle's magnetic “remnant” field. If the vehicle is subjected to high magnetic influ-
ences, the compass may appear to indicate false headings, become locked, or appear that it is unable to be
calibrated. If this occurs, perform the calibration procedure.
• If at any time the compass continually displays an incorrect direction or the reading is erratic or locked, verify
the correct zone variance.
Symptom Chart
INFORMATION DISPLAY
INFORMATION DISPLAY : Description
INFOID:0000000007565151
AMBIENT AIR TEMPERATURE
The displayed ambient air temperature on the information display may differ from the actual temperature
because it is a corrected value calculated from the ambient sensor signal by the combination meter. Refer to
MWI-15, "INFORMATION DISPLAY : System Description"
for details on the correction process.
POSSIBLE DRIVING DISTANCE
The calculated possible driving distance may differ from the actual distance to empty if the refueling amount is
approximately 15 (4 US gal, 3-1/4 Imp gal) or less. This is because the refuel control (moves the fuel gauge
needle quicker than normal judging that the driver is refueling the vehicle) is not performing.
Symptom
Cause
Solution / Reference
The compass display reads “C”.
• Compass is not calibrated.
• Incorrect zone variance setting.
• Large change in magnetic field (Steel
bridges, subways, concentrations of
metal, carwashes, etc.)
• Compass was calibrated incorrectly or in
the presence of a strong magnetic field.
.
Compass shows the wrong direction.
Compass does not change direction ap-
pears “Locked”.
Compass does not show all the directions,
one or more is missing.
The compass was calibrated but it “loses”
calibration.
On long trips the compass shows the
wrong direction.
Perform zone variation setting if correct
reading is desired in that location. Refer
to
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-70
< REMOVAL AND INSTALLATION >
COMBINATION METER
REMOVAL AND INSTALLATION
COMBINATION METER
Exploded View
INFOID:0000000007565152
.
DISASSEMBLY
Removal and Installation
INFOID:0000000007565153
REMOVAL
Removal
1.
Remove the cluster lid A. Refer to
IP-13, "Removal and Installation"
.
2.
Remove screws (A) and connector, and remove combination
meter (1).
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000007565154
DISASSEMBLY
Disengage the pawls and pull the front cover straight to remove it from the unified meter control unit.
CAUTION:
• Never touch the display, pointer, the inside of front cover and the printed area of the dial during the
work.
• Keep away from magnetic sources.
• Never damage the front cover.
ASSEMBLY
Install the front cover straight to the unified meter control unit and engage all the pawl.
CAUTION:
JSNIA4286ZZ
1.
Unified meter control unit
2.
Front cover
JPNIA0810ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
COMBINATION METER
MWI-71
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• Never touch the display, pointer, the inside of front cover and the printed area of the dial during the
work.
• Keep away from magnetic sources.
• Never damage the front cover.
Revision: 2013 February
2012 Murano CrossCabriolet
MWI-72
< REMOVAL AND INSTALLATION >
METER CONTROL SWITCH
METER CONTROL SWITCH
Exploded View
INFOID:0000000007565155
REMOVAL
.
DISASSEMBLY
Removal and Installation
INFOID:0000000007565156
REMOVAL
1.
Remove cluster lid A. Refer to
2.
Remove meter control switch connectors and remove meter control switches.
INSTALLATION
Install in the reverse order of removal.
JPNIA0812ZZ
1.
Meter control switch (LH)
2.
Meter control switch (RH)
3.
Cluster lid A
Revision: 2013 February
2012 Murano CrossCabriolet
MWI
COMPASS
MWI-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
COMPASS
Exploded View
INFOID:0000000007565157
.
Removal and Installation
INFOID:0000000007565158
MIR-18, "Removal and Installation"
.
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст