Murano Cross Cabriolet Z51 (2012 year). Manual — part 32
EXL-36
< BASIC INSPECTION >
[XENON TYPE]
DIAGNOSIS AND REPAIR WORKFLOW
YES
>> GO TO 9.
NO
>> Check according to
GI-40, "Intermittent Incident"
.
8.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES
>> GO TO 9.
NO
>> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
9.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 10.
NO
>> Check according to
GI-40, "Intermittent Incident"
.
10.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 11.
11.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 9.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
Revision: 2013 February
2012 Murano CrossCabriolet
HEADLAMP (HI) CIRCUIT
EXL-37
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DTC/CIRCUIT DIAGNOSIS
HEADLAMP (HI) CIRCUIT
Component Function Check
INFOID:0000000007565434
1.
CHECK HEADLAMP (HI) OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp switches to the high beam.
NOTE:
HI/LO is repeated 1 second each.
Does the headlamp switch to the high beam?
YES
>> Headlamp (HI) circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565435
1.
CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect high beam solenoid connector.
3.
Turn ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK HEADLAMP (HI) OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and high beam solenoid harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
Hi
: Headlamp switches to the high beam.
Off
: Headlamp OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E345
89
Ground
EXTERNAL LAMPS
Hi
Battery voltage
Off
0 V
LH
90
Hi
Battery voltage
Off
0 V
IPDM E/R
High beam solenoid
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
89
E326
1
Existed
LH
90
E325
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-38
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (HI) CIRCUIT
3.
CHECK HEADLAMP (HI) FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 4.
4.
CHECK HEADLAMP (HI) SHORT CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector terminal and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
5.
CHECK HEADLAMP (HI) GROUND OPEN CIRCUIT
Check continuity between high beam solenoid harness connector and ground.
Is the inspection result normal?
YES
>> Replace front combination lamp.
NO
>> Repair or replace harness.
Unit
Location
Fuse No.
Capacity
Headlamp HI (RH)
IPDM E/R
#55
10 A
Headlamp HI (LH)
#54
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
89
Not existed
LH
90
High beam solenoid
Ground
Continuity
Connector
Terminal
RH
E326
2
Existed
LH
E325
Revision: 2013 February
2012 Murano CrossCabriolet
HEADLAMP (LO) CIRCUIT
EXL-39
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP (LO) CIRCUIT
Component Function Check
INFOID:0000000007565436
1.
CHECK HEADLAMP (LO) OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp (LO) is turned ON.
Is the headlamp (LO) turned ON?
YES
>> Headlamp (LO) is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565437
1.
CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect headlamp connector.
3.
Turn ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK HEADLAMP (LO) OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and headlamp harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
3.
CHECK HEADLAMP (LO) FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Lo
: Headlamp (LO) ON
Off
: Headlamp (LO) OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E345
83
Ground
EXTERNAL LAMPS
Lo
Battery voltage
Off
0 V
LH
84
Lo
Battery voltage
Off
0 V
IPDM E/R
Headlamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
83
E324
1
Existed
LH
84
E323
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-40
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (LO) CIRCUIT
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 4.
4.
CHECK HEADLAMP (LO) SHORT CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
5.
CHECK HEADLAMP (LO) GROUND OPEN CIRCUIT
Check continuity between headlamp harness connector and ground.
Is the inspection result normal?
YES
>> Perform the xenon headlamp diagnosis. Refer to
.
NO
>> Repair or replace harness.
Unit
Lotion
Fuse No.
Capacity
Headlamp LO (RH)
IPDM E/R
#57
15 A
Headlamp LO (LH)
#56
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
83
Not existed
LH
84
Headlamp
Ground
Continuity
Connector
Terminal
RH
E324
2
Existed
LH
E323
Revision: 2013 February
2012 Murano CrossCabriolet
XENON HEADLAMP
EXL-41
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
XENON HEADLAMP
Diagnosis Procedure
INFOID:0000000007565438
1.
CHECK XENON BULB
Install the normal bulb to the applicable headlamp. Check that the lighting switch is turned ON.
Is the headlamp turned ON?
YES
>> Replace the xenon bulb.
NO
>> GO TO 2.
2.
CHECK HID CONTROL UNIT
Install the normal HID control unit to the applicable headlamp. Check that the lighting switch is turned ON.
Is the headlamp turned ON?
YES
>> Replace HID control unit.
NO
>> Xenon headlamp is normal. Check the headlamp control system.
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-42
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
PARKING LAMP CIRCUIT
PARKING LAMP CIRCUIT
Component Function Check
INFOID:0000000007565439
1.
CHECK PARKING LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the parking lamp is turned ON.
Is the parking lamp turned ON?
YES
>> Parking lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565440
1.
CHECK PARKING LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PARKING LAMP SHORT CIRCUIT
1.
Disconnect IPDM E/R connector and parking lamp connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK PARKING LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the bulb.
4.
CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Disconnect parking lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating test items, check voltage between IPDM E/R harness connector and ground.
TAIL
: Parking lamp ON
Off
: Parking lamp OFF
Unit
Location
Fuse No.
Capacity
Parking lamp / Front side marker lamp
IPDM E/R
#52
10 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E346
91
Not existed
LH
92
Revision: 2013 February
2012 Murano CrossCabriolet
PARKING LAMP CIRCUIT
EXL-43
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK PARKING LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and parking lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal?
YES-1 >> (When tail lamp does not turn ON) Replace rear combination lamp.
YES-2 >> (When rear side marker lamp does not turn ON) Check corresponding bulb socket and harness.
Repair or replace if necessary.
NO
>> Repair or replace harness.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E346
91
Ground
EXTERNAL LAMPS
TAIL
Battery voltage
Off
0 V
LH
92
TAIL
Battery voltage
Off
0 V
IPDM E/R
Parking lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E346
91
E330
1
Existed
LH
92
E329
Parking lamp
Ground
Continuity
Connector
Terminal
RH
E330
2
Existed
LH
E329
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-44
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
FRONT SIDE MARKER LAMP CIRCUIT
FRONT SIDE MARKER LAMP CIRCUIT
Component Function Check
INFOID:0000000007565441
NOTE:
Check parking lamp circuit if parking lamp and front side marker lamp are not turned ON. Refer to
1.
CHECK FRONT SIDE MARKER LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front side marker lamp is turned ON.
Is the front side marker lamp turned ON?
YES
>> Front side marker lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565442
1.
CHECK FRONT SIDE MARKER LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and front side marker lamp connector.
3.
Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FRONT SIDE MARKER LAMP GROUND OPEN CIRCUIT
Check continuity between front side marker lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: Front side marker lamp ON
Off
: Front side marker lamp OFF
IPDM E/R
Front side marker lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E346
91
E315
1
Existed
LH
92
E314
Front side marker lamp
Ground
Continuity
Connector
Terminal
RH
E315
2
Existed
LH
E314
Revision: 2013 February
2012 Murano CrossCabriolet
TAIL LAMP CIRCUIT
EXL-45
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TAIL LAMP CIRCUIT
Component Function Check
INFOID:0000000007565443
1.
CHECK TAIL LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the tail lamp is turned ON.
Is the tail lamp turned ON?
YES
>> Tail lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565444
1.
CHECK TAIL LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK TAIL LAMP SHORT CIRCUIT
1.
Disconnect IPDM E/R connector, rear combination lamp connector and license plate lamp connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK TAIL LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Disconnect rear combination lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace IPDM E/R.
TAIL
: Tail Lamp ON
Off
: Tail lamp OFF
Unit
Location
Fuse No.
Capacity
Tail lamp / Rear side marker lamp / License plate lamp
IPDM E/R
#53
10 A
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
7
Not existed
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E10
7
Ground
EXTERNAL
LAMPS
TAIL
Battery
voltage
Off
0 V
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-46
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
TAIL LAMP CIRCUIT
4.
CHECK TAIL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear combination lamp.
NO
>> Repair or replace harness.
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E10
7
B86
4
Existed
LH
B59
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B86
1
Existed
LH
B59
Revision: 2013 February
2012 Murano CrossCabriolet
LICENSE PLATE LAMP CIRCUIT
EXL-47
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000007565445
NOTE:
Check tail lamp circuit if tail lamp and license plate lamp are not turned ON. Refer to
1.
CHECK LICENSE PLATE LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the lighting switch, check that the license plate lamp is turned ON.
Is the license plate lamp turned ON?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565446
1.
CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and license plate lamp connector.
3.
Check continuity between IPDM E/R harness connector and license plate lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between license plate lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
License plate lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E10
7
T9
1
Existed
LH
T6
License plate lamp
Ground
Continuity
Connector
Terminal
RH
T9
2
Existed
LH
T6
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-48
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000007565447
1.
CHECK TURN SIGNAL LAMP
CONSULT ACTIVE TEST
1.
Select “FLASHER” of BCM (FLASHER) active test item.
2.
With operating the test items, check that the turn signal lamp is turned ON.
Is the turn signal lamp turned ON?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565448
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect front turn signal lamp connector or rear combination lamp connector.
3.
Turn ignition switch ON.
4.
With operating turn signal switch, check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
(+)
(
−
)
Condition
Voltage (Approx.)
BCM
Connector
Terminal
RH
M119
17
Ground
Turn signal
switch
RH
OFF
0 V
LH
18
LH
OFF
0 V
PKID0926E
PKID0926E
Revision: 2013 February
2012 Murano CrossCabriolet
TURN SIGNAL LAMP CIRCUIT
EXL-49
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and front turn signal lamp or rear combination lamp
harness connector.
Front turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer
to
BCS-76, "Removal and Installation"
.
NO
>> Repair or replace harness.
5.
CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between front turn signal lamp or rear combination lamp and ground.
Front turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary
NO
>> Repair or replace harness.
BCM
Front turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M119
17
E328
1
Existed
LH
18
E327
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M119
17
B86
2
Existed
LH
18
B59
BCM
Ground
Continuity
Connector
Terminal
RH
M119
17
Not existed
LH
18
Front turn signal lamp
Ground
Continuity
Connector
Terminal
RH
E328
2
Existed
LH
E327
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B86
1
Existed
LH
B59
Revision: 2013 February
2012 Murano CrossCabriolet
EXL-50
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000007565449
1.
CHECK FRONT FOG LAMP OPERATION
CONSULT ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front fog lamp is turned ON.
Is the front fog lamp turned ON?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007565450
1.
CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect front fog lamp connector.
3.
Turn ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating the test items, check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R.
3.
CHECK FRONT FOG LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
Fog
: Front fog lamp ON
Off
: Front fog lamp OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E345
86
Ground
EXTERNAL
LAMPS
Fog
Battery voltage
Off
0 V
LH
87
Fog
Battery voltage
Off
0 V
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
86
E402
1
Existed
LH
87
E412
Revision: 2013 February
2012 Murano CrossCabriolet
FRONT FOG LAMP CIRCUIT
EXL-51
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NO
>> Repair or replace harness.
4.
CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT
Check continuity between front fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace harness.
Front fog lamp
Ground
Continuity
Connector
Terminal
RH
E402
2
Existed
LH
E412
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст