Murano Cross Cabriolet Z51 (2012 year). Manual — part 108
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
WT-37
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000007565900
The low tire pressure warning lamp does not illuminate when the ignition switch is turned ON.
NOTE:
The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000007565901
1.
CHECK LOW TIRE PRESSURE WARNING LAMP
Perform trouble diagnosis of the low tire pressure warning lamp. Refer to
Is the inspection result normal?
YES
>> Check pin terminal and connection of each connector for damage and loose connection.
NO
>> Repair or replace damaged parts.
Revision: 2013 February
2012 Murano CrossCabriolet
WT-38
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000007565902
The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.
Diagnosis Procedure
INFOID:0000000007565903
1.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp display.
Does not low tire pressure warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK BCM
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-76, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
Revision: 2013 February
2012 Murano CrossCabriolet
LOW TIRE PRESSURE WARNING LAMP BLINKS
WT-39
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000007565904
The low tire pressure warning lamp blinks when the ignition switch is turned ON.
NOTE:
The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low tire
pressure warning lamp.
Diagnosis Procedure
INFOID:0000000007565905
1.
TIRE PRESSURE SENSOR WAKE-UP OPERATION
Perform the tire pressure sensor wake-up. Refer to
.
Is the tire pressure sensor wake-up completed?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis for the tire pressure sensor. Refer to
.
2.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> Perform the self-diagnosis for “AIR PRESSURE MONITOR”. Refer to
JPEIC0089GB
Revision: 2013 February
2012 Murano CrossCabriolet
WT-40
< SYMPTOM DIAGNOSIS >
ID REGISTRATION CANNOT BE COMPLETED
ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000007565906
The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000007565907
1.
TIRE PRESSURE SENSOR WAKE-UP
Perform the tire pressure sensor wake-up. Refer to
.
Is the tire pressure sensor wake-up completed?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL
Check tire pressure sensor activation tool.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sen-
sor activation tool.
3.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
CHECK TIRE PRESSURE SIGNAL
Change the work location and perform ID registration again.
NOTE:
Depending on the tire pressure sensor position*, a blind spot exists, and the tire pressure receiver gets a
poor reception. If an ID registration is performed under this condition, the registration may not be completed.
In such case, follow the instructions below to improve the radio wave receiving environment.
• Rotate tire by 90
°
, 180
°
, or 270
°
. (This Step is to change tire pressure sensor position.)
• Open the door close to the tire of which ID registration is ongoing.
*: Radio wave reception condition depends on vehicle architecture (e.g. body harness layout, tire wheel
design) or environment.
When ID registration is performed, which wheels do not react?
All wheels react and ID registration is possible.>>INSPECTION END
Only certain wheel(s) do not react.>>Replace applicable tire pressure sensor. Refer to
All wheels do not react.>>Check the tire pressure receiver. Refer to
WT-30, "Component Function Check"
Revision: 2013 February
2012 Murano CrossCabriolet
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
WT-41
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000007565908
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
,
.
—
—
NVH in DLN section.
NVH in DLN section.
NVH in F
AX and FSU sections.
NVH
in
RAX and RSU sections.
Re
fer t
o
T
IRES i
n
t
h
is cha
rt.
Re
fe
r to
ROAD WHEEL
in
th
is ch
art
.
NVH i
n
F
AX,
R
A
X section.
NVH in BR section.
NV
H
in
S
T
s
e
cti
on
.
Possible cause and SUSPECTED PARTS
Imp
rop
er i
ns
ta
lla
ti
o
n,
lo
os
en
es
s
Out
-of-ro
un
d
un
ba
lan
c
e
Incorrect t
ire
pressure
Uneven tire
wear
Def
o
rm
ati
o
n
o
r da
ma
ge
No
n-u
n
if
ormi
ty
In
co
rrec
t t
ire
si
ze
PROPELLER SHAFT
DIFF
ERENTIAL
FRONT A
X
LE
AND FRONT SUSP
ENSION
REAR A
X
LE
AND REAR SUSP
ENSION
TI
RE
S
ROAD WHEE
LS
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
TIRES
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Shimmy, Judder
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
Revision: 2013 February
2012 Murano CrossCabriolet
WT-42
< PERIODIC MAINTENANCE >
ROAD WHEEL
PERIODIC MAINTENANCE
ROAD WHEEL
Inspection
INFOID:0000000007565909
APPEARANCE
Check the road wheel for bend, damage, crack or wear.
Wheel Balance Adjustment
INFOID:0000000007565910
PREPARATION BEFORE ADJUSTMENT
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for aluminum wheels.
1.
Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Do not install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, be sure to clean the mating surface of the road wheel.
a.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz)
⇒
40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒
35 g (1.23 oz)
37.5
⇒
40 g (1.41 oz)
b.
Installed balance weight in the position.
SMA054D
Revision: 2013 February
2012 Murano CrossCabriolet
ROAD WHEEL
WT-43
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
• When installing balance weight (1) to road wheels, set it into
the grooved area (A) on the inner wall of the road wheel as
shown in the figure so that the balance weight center (B) is
aligned with the tire balance machine indication position
(angle) (C).
CAUTION:
• Always use genuine NISSAN adhesion balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install three or more sheets of balance weight.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Do not install one balance weight sheet on top of another.
3.
Start the tire balance machine again.
4.
Install drive-in balance weight on inner side of road wheel in the
tire balance machine indication position (angle).
CAUTION:
Do not install three or more balance weight.
5.
Start the tire balance machine. Check that inner and outer resid-
ual unbalance values is within the allowable unbalance value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
Tire Rotation
INFOID:0000000007565911
• Follow the maintenance schedule for tire rotation service intervals.
MA-4, "Explanation of General Maintenance"
.
• When installing the wheel, tighten wheel nuts to the specified
.
CAUTION:
• Do not include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
• Use NISSAN genuine wheel nuts for aluminum wheels.
• Perform the ID registration, after tire rotation. Refer to
JPEIC0040ZZ
Allowable unbalance value
Dynamic (At flange):
Refer to
.
Static (At flange):
Refer to
.
PEIA0033E
SMA829C
Revision: 2013 February
2012 Murano CrossCabriolet
WT-44
< REMOVAL AND INSTALLATION >
ROAD WHEEL TIRE ASSEMBLY
REMOVAL AND INSTALLATION
ROAD WHEEL TIRE ASSEMBLY
Exploded View
INFOID:0000000007565912
Removal and Installation
INFOID:0000000007565913
REMOVAL
1.
Remove wheel nuts.
2.
Remove tire assembly.
INSTALLATION
Note the following, install in the reverse order of removal.
• When replacing or rotating wheels, perform the ID registration. Refer to
.
Inspection
INFOID:0000000007565914
ALUMINUM WHEEL
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from aluminum wheel and mount on a tire balance machine.
b.
Set dial indicator as shown in the figure.
c.
Check runout, If the axial runout (A) or radial runout (B) exceeds
the limit, replace aluminum wheel.
1.
Tire assembly
: N·m (kg-m, ft-lb)
JSGIA0639GB
Limit
Axial runout (A)
: Refer to
.
Radial runout (B)
: Refer to
.
SEIA0737E
Revision: 2013 February
2012 Murano CrossCabriolet
ROAD WHEEL TIRE ASSEMBLY
WT-45
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
How to Handle Puncture Repair Agent
INFOID:0000000007565915
CAUTION:
• Never spill the sealant in the tire during repair.
• If the sealant spills, wipe it out with a waste cloth.
• Never reuse the repair kit hose used for a temporary repair of a flat tire because some of the punc-
ture repair agent remains in the hose.
• After using a puncture repair agent, replace tire pressure sensor with a new one.
1.
Remove tires from the vehicle.
2.
Remove tire from road wheel, using a tire changer.
CAUTION:
• When deflating a tire, cover the tire pressure sensor with a waste cloth to prevent the sealant
from splattering.
• Never spill the sealant in the tire during repair.
3.
Dispose of sealant in the removed tire.
CAUTION:
• Wipe out sealant spilled on the road wheel, tire, tire changer, and floor with a waste cloth.
• Drained sealant or expired sealant returned by the customer must be disposed according to the
law and local regulations.
• Fix a tire blowout, if repairable.
NOTE:
Sealant blocks holes caused by blowouts. These holes may not be found and repaired, depending on
the level of blowout. Therefore, it is necessary to check tire air pressure frequently and replace tire with
a new one, if the air pressure is decreasing.
• Replace tire with a new one, if not repairable.
CAUTION:
Never dispose of tires with the sealant contained.
Revision: 2013 February
2012 Murano CrossCabriolet
WT-46
< REMOVAL AND INSTALLATION >
TIRE PRESSURE SENSOR
TIRE PRESSURE SENSOR
Exploded View
INFOID:0000000007565916
Removal and Installation
INFOID:0000000007565917
REMOVAL
1.
Remove tire assembly. Refer to
WT-44, "Removal and Installation"
2.
Remove valve cap, valve core and then deflate tire.
NOTE:
If the tire is reused, apply a matching mark to the position of the tire road wheel valve hole for the purpose
of wheel balance adjustment after installation.
3.
Remove valve nut retaining tire pressure sensor and allow tire pressure sensor to fall into tire.
4.
Use the tire changer and disengage the tire beads.
CAUTION:
• Verify that the tire pressure sensor (1) is at the bottom of
the tire while performing the above.
• Be sure not to damage the road wheel or tire pressure
sensor.
5.
Apply bead cream or an equivalent to the tire beads.
6.
Set tire onto the tire changer turntable so that the tire pressure
sensor inside the tire is located close to the road wheel valve
hole.
JSEIA0384GB
1.
Tire pressure sensor
2.
Grommet seal
3.
Valve nut
4.
Valve core
5.
Valve cap
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Parts that are replaced as a set when the tire is replaced.
JPEIC0104ZZ
Revision: 2013 February
2012 Murano CrossCabriolet
TIRE PRESSURE SENSOR
WT-47
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
7.
Turn tire so that valve hole is at bottom and bounce so that tire
pressure sensor (1) is near valve hole. Carefully lift tire onto
turntable and position valve hole (and tire pressure sensor) 270
degree from mounting/dismounting head (2).
CAUTION:
Be sure not to damage the road wheel and tire pressure
sensor.
8.
Remove tire pressure sensor from tire.
9.
Remove the grommet seal.
INSTALLATION
1.
Apply bead cream or an equivalent to the tire beads.
2.
Install the tire inside beads (1) onto the road wheel (2) in the
position shown in the figure.
3.
Install grommet seal to the tire pressure sensor.
CAUTION:
• Never reuse grommet seal.
• Insert grommet seal all the way to the base.
4.
Hold tire pressure sensor as shown in the figure, and press the
sensor in the direction shown by arrow (
) to bring it into abso-
lute contact with valve hole. After this, tighten valve nut to the
specified torque.
CAUTION:
• Never reuse valve core and valve cap.
• Check that grommet seal is free of foreign matter.
• Check that grommet seal contacts horizontally with road
wheel.
• Manually tighten valve nut all the way to the wheel. (Never
use a power tool to avoid impact.)
5.
Set the tire onto the turntable so that the tire changer arm (2) is
at a position approximately 270
°
from the tire pressure sensor
(1).
CAUTION:
Be sure that the arm does not contact the tire pressure sen-
sor.
6.
Install the tire outer side beads onto the road wheel.
CAUTION:
When installing, check that the tire does not turn together
with the road wheel.
7.
Check the tire pressure for all wheels and adjust to the specified
value. Refer to
NOTE:
Before adding air, align the tire with the position of the matching mark applied at the time of removal.
8.
Install tire to the vehicle. Refer to
WT-44, "Removal and Installation"
9.
Perform tire pressure sensor ID registration. Refer to
.
JPEIC0014GB
JPEIC0105ZZ
JSEIA0466GB
JPEIC0014GB
Revision: 2013 February
2012 Murano CrossCabriolet
WT-48
< REMOVAL AND INSTALLATION >
TIRE PRESSURE RECEIVER
TIRE PRESSURE RECEIVER
Removal and Installation
INFOID:0000000007565918
REMOVAL
1.
Remove the instrument lower panel LH. Refer to
.
2.
Disconnect tire pressure receiver harness connector.
3.
Remove tire pressure receiver.
INSTALLATION
Install is the reverse order of removal.
Revision: 2013 February
2012 Murano CrossCabriolet
SERVICE DATA AND SPECIFICATIONS (SDS)
WT-49
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000007565919
ALUMINUM WHEEL
Tire Air Pressure
INFOID:0000000007565920
Unit: kPa (kg/cm
2
, psi)
Item
Limit
Runout
Axial runout
Less than 0.3 mm (0.012 in)
Radial runout
Allowable unbalance
Dynamic (At flange)
Less than 5 g (0.17 oz) (one side)
Static (At flange)
Less than 10 g (0.35 oz)
Item
Standard
Front
Rear
P235/55R20 102T
230 (2.3, 33)
Revision: 2013 February
2012 Murano CrossCabriolet
WW-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
WW
A
B
WW
N
O
P
CONTENTS
WIPER & WASHER
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Precaution for Battery Service . . . . . . . . ..
Precaution for Procedure without Cowl Top Cover
. ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . ....
Washer Switch . . . . . . . . . . . . . . ..
SYSTEM . . . . . . . . . . . . . . . ..
FRONT WIPER AND WASHER SYSTEM . . . . ...
FRONT WIPER AND WASHER SYSTEM : Sys-
tem Diagram . . . . . . . . . . . . . . . ..
FRONT WIPER AND WASHER SYSTEM : Sys-
tem Description . . . . . . . . . . . . . .....
FRONT WIPER AND WASHER SYSTEM : Fail-
Safe . . . . . . . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
WIPER . . . . . . . . . . . . . . . . . ...
WIPER : CONSULT Function - WIPER . . . . ..
DIAGNOSIS SYSTEM (IPDM E/R) . . . . . .
Diagnosis Description . . . . . . . . . . . .
CONSULT Function (IPDM E/R) . . . . . . . .
ECU DIAGNOSIS INFORMATION . . . ..
BCM, IPDM E/R . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
WIPER AND WASHER SYSTEM . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
FRONT WIPER MOTOR LO CIRCUIT . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER MOTOR HI CIRCUIT . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER STOP POSITION SIGNAL
CIRCUIT . . . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
FRONT WIPER MOTOR GROUND CIRCUIT ...
Diagnosis Procedure . . . . . . . . . . . ...
WASHER SWITCH . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
WIPER AND WASHER SYSTEM SYMPTOMS
...
Symptom Table . . . . . . . . . . . . . ...
NORMAL OPERATING CONDITION . . . ...
Description . . . . . . . . . . . . . . . ...
Revision: 2013 February
2012 Murano CrossCabriolet
WW-2
FRONT WIPER DOES NOT OPERATE . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
WASHER TANK . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
WASHER PUMP . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
WASHER LEVEL SWITCH . . . . . . . .
Removal and Installation . . . . . . . . . ....
WASHER NOZZLE & TUBE . . . . . . . ..
Exploded View . . . . . . . . . . . . . ....
Hydraulic Layout . . . . . . . . . . . . . .
WASHER NOZZLE . . . . . . . . . . . . ...
WASHER NOZZLE : Removal and Installation . ..
WASHER NOZZLE : Inspection and Adjustment .
WASHER TUBE . . . . . . . . . . . . . .
WASHER TUBE : Removal and Installation . . ...
FRONT WIPER ARM . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Adjustment . . . . . . . . . . . . . . . ..
WIPER BLADE . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
FRONT WIPER DRIVE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . .
WIPER AND WASHER SWITCH . . . . . ..
Exploded View . . . . . . . . . . . . . .
Revision: 2013 February
2012 Murano CrossCabriolet
PRECAUTIONS
WW-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007566605
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000007566606
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Precaution for Battery Service
INFOID:0000000007566607
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Revision: 2013 February
2012 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст