Qashqai J11. Driver assistance system — part 16
DAS
CONFIGURATION (CHASSIS CONTROL MODULE)
DAS-241
< BASIC INSPECTION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CONFIGURATION (CHASSIS CONTROL MODULE)
Work Procedure
INFOID:0000000010416984
CAUTION:
• Use “Manual Configuration” only when “TYPE ID” of the chassis control module cannot be read.
• After configuration, turn the ignition switch from OFF to ON and check that the chassis control warn-
ing to information display of combination meter displays OFF after staying illuminated for approxi-
mately two seconds.
• If an error occurs during configuration, start over from the beginning.
1.
CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search the chassis control module of the applicable vehicle and find
“Type ID”.
Is “Type ID” displayed?
YES
>> Print out “Type ID” and GO TO 2.
NO
>> “Configuration” is not required for the chassis control module. Replace in the usual manner. Refer
to
DAS-312, "Removal and Installation"
2.
CHECKING TYPE ID (2)
CONSULT Configuration
1.
Select “Before Replace ECU” of “Read/Write Configuration”.
2.
Check that “Type ID” is displayed on the CONSULT screen.
Is “Type ID” displayed?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
VERIFYING TYPE ID (1)
CONSULT Configuration
Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 4.
4.
SAVING TYPE ID
CONSULT Configuration
Save “Type ID” on CONSULT.
>> GO TO 5.
5.
REPLACING CHASSIS CONTROL MODULE (1)
Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
>> GO TO 6.
6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1.
Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.
2.
Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the chassis control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
7.
REPLACING CHASSIS CONTROL MODULE (2)
DAS-242
< BASIC INSPECTION >
[CHASSIS CONTROL]
CONFIGURATION (CHASSIS CONTROL MODULE)
Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
>> GO TO 8.
8.
WRITING (MANUAL WRITING)
CONSULT Configuration
1.
Select “Manual Configuration”.
2.
Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the
chassis control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
9.
VERIFYING TYPE ID (2)
Compare “Type ID” written into the chassis control module with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 10.
10.
CHECKING CHASSIS CONTROL WARNING
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON and check that the chassis control warning to information display of combina-
tion meter displays OFF after staying illuminated for approximately two seconds.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Perform the “Self Diagnostic Result” of “CHASSIS CONTROL”. Refer to
.
11.
PERFORMING SUPPLEMENTARY WORK
1.
Perform the self-diagnosis of all systems.
2.
Erase self-diagnosis results.
>> End of work.
DAS
C1B92-00 BRAKE CONTROL SYSTEM
DAS-243
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
DTC/CIRCUIT DIAGNOSIS
C1B92-00 BRAKE CONTROL SYSTEM
DTC Description
INFOID:0000000010416985
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit) system
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control function
• Active Trace Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B92-00” detected?
YES
>> Proceed to
DAS-243, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416986
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1B92”, “U1000” or other DTC detected?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B92-00
BRAKE CONTROL SYSTEM
(Brake control system)
When a malfunction is detected in ABS actuator and electric unit (control unit) sys-
tem.
DAS-244
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1B92-00 BRAKE CONTROL SYSTEM
YES (“C1B92-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS
C1B93-00 ENGINE/HEV SYSTEM
DAS-245
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1B93-00 ENGINE/HEV SYSTEM
DTC Description
INFOID:0000000010416987
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Engine system
• ECM
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B93-00” detected?
YES
>> Proceed to
DAS-245, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416988
1.
CHECK ECM SYSTEM
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is DTC detected?
YES
>> Check the DTC. Refer to
(HRA2DDT),
(K9K) or
(R9M)
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1B93-00”, “U1000-00” or other DTC detected?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B93-00
ENGINE/HEV SYSTEM
(Engine/HEV system)
When a malfunction is detected in ECM system.
DAS-246
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1B93-00 ENGINE/HEV SYSTEM
YES (“C1B93-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS
C1B94-00 TRANSMISSION SYSTEM
DAS-247
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1B94-00 TRANSMISSION SYSTEM
DTC Description
INFOID:0000000010416989
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Transmission system
• TCM
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B94-00” detected?
YES
>> Proceed to
DAS-247, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416990
1.
CHECK TRANSMISSION SYSTEM
With CONSULT
Perform self-diagnosis for “TRANSMISSION”.
Is DTC detected?
YES
>> Check the DTC. Refer to
(RE0F10D) or
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1B94-00”, “U1000-00” or other DTC detected?
YES (“C1B94-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B94-00
TM SYSTEM
(Transmission system)
When a malfunction is detected in transmission system.
DAS-248
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1B94-00 TRANSMISSION SYSTEM
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS
C1B95-00 CONTROL MODULE
DAS-249
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1B95-00 CONTROL MODULE
DTC Description
INFOID:0000000010416991
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Trace Control function
• Active Ride Control (brake) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B95-00” detected?
YES
>> Proceed to
DAS-249, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416992
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B95-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
NO
>> INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B95-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS-250
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1B99-00 CONTROL MODULE
C1B99-00 CONTROL MODULE
DTC Description
INFOID:0000000010416993
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control function
• Active Trace Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B99-00” detected?
YES
>> Proceed to
DAS-250, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416994
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B99-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
NO
>> INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B99-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS
C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM
DAS-251
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM
DTC Description
INFOID:0000000010416995
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit)
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Trace Control function
• Active Ride Control (brake) function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BA0-00” detected?
DAS-251, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416996
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1BA0-00”, “U1000-00” or other DTC detected?
YES (“C1BA0-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BA0-00
ADAS/CHASSIS CTRL BRAKE
SYS
(ADAS/Chassis Control brake
system)
When receiving from ABS actuator and electric unit (control unit) that the value of
the brake system signal transmitted from the chassis control module to ABS actu-
ator and electric unit (control unit) is malfunctioning.
DAS-252
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS
C1BA2-00 STEERING ANGLE SENSOR
DAS-253
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BA2-00 STEERING ANGLE SENSOR
DTC Description
INFOID:0000000010416997
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Steering angle sensor
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BA2-00” detected?
YES
>> Proceed to
DAS-253, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416998
1.
CHECK STEERING ANGLE SENSOR SYSTEM
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1BA2-00”, “U1000-00” or other DTC detected?
YES (“C1BA2-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BA2-00
STEERING ANGLE SENSOR
(Steering angle sensor)
When a malfunction is detected in steering angle sensor system.
DAS-254
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BA2-00 STEERING ANGLE SENSOR
NO
>> INSPECTION END
DAS
C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM
DAS-255
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM
DTC Description
INFOID:0000000010416999
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis Control Module
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BA5-00” detected?
YES
>> Proceed to
DAS-255, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010417000
1.
CHECK ECM SYSTEM
With CONSULT
Perform self-diagnosis for “ECM”.
Is DTC detected?
YES
>> Check the DTC. Refer to
(HRA2DDT),
(K9K) or
(R9M).
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1BA5-00”, “U1000-00” or other DTC detected?
YES (“C1BA5-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BA5-00
ADAS/CHASSIS CTRL ENGINE
SYS
(ADAS/Chassis control engine
system)
• When receiving from ECM that the value of the engine system signal transmitted
from the chassis control module to ECM is malfunctioning.
DAS-256
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BAB-00 STOP LAMP SWITCH
C1BAB-00 STOP LAMP SWITCH
DTC Description
INFOID:0000000010417001
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Stop lamp switch
• BCM
• Chassis Control Module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BAB-00” detected?
YES
>> Proceed to
DAS-256, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010417002
1.
CHECK STOP LAMP SWITCH SYSTEM
With CONSULT
Perform self-diagnosis for “BCM”.
Is DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1BAB-00”, “U1000-00” or other DTC detected?
YES (“C1BAB-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BAB-00
STOP LAMP SW
(Stop lamp switch)
When a malfunction is detected in stop lamp switch system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст