Nissan Murano Z50 (2004 year). Manual — part 61
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-195
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
Vehicle Does Not Creep Forward in “D”, “S” or “L” Position
ACS004MQ
SYMPTOM:
Vehicle does not creep forward when selecting “D”, “S”*, or “L”* position.
*: Without manual mode
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
CVT-62, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-209, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
.
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
"Judgement of Line Pressure Test"
.
SCIA2001E
SAT638A
SAT494G
CVT-196
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November
2004 Murano
5.
SYMPTOM CHECK
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signal. Refer to
CVT-56, "TCM Input/Output Signal Reference Values"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-224, "Removal and Installation"
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-197
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
CVT Does Not Shift
ACS004MR
SYMPTOM:
CVT does not shift at the specified speed on “Cruise Test”.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
CVT-62, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-209, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
.
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
"Judgement of Line Pressure Test"
.
SCIA2001E
SAT638A
SAT494G
CVT-198
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November
2004 Murano
5.
SYMPTOM CHECK
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signal. Refer to
CVT-56, "TCM Input/Output Signal Reference Values"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-224, "Removal and Installation"
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-199
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
Cannot Be Changed to Manual Mode
ACS004Z8
SYMPTOM:
Does not change to manual mode when manual shift gate is used.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
CVT-62, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK MANUAL MODE SWITCH
Check manual mode switch circuit. Refer to
CVT-132, "DTC P0826 MANUAL MODE SWITCH CIRCUIT"
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
SYMPTOM CHECK
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 4.
4.
CHECK TCM
1.
Check TCM input/output signal. Refer to
CVT-56, "TCM Input/Output Signal Reference Values"
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
CVT-200
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November
2004 Murano
CVT Does Not Shift in Manual Mode
ACS004Z9
SYMPTOM:
Speed does not change even if the selector lever is put in the manual shift gate position and the selec-
tor lever is operated on + side on - side.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
CVT-62, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnostic?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK MANUAL MODE SWITCH
Check manual mode switch circuit. Refer to
CVT-132, "DTC P0826 MANUAL MODE SWITCH CIRCUIT"
.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-209, "Checking of CVT Position"
OK or NG
OK
>> GO TO 4.
NG
>> Adjust control cable. Refer to
4.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Refill CVT fluid.
SCIA2001E
SAT638A
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-201
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
5.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 6.
NG
>> Check the malfunctioning item. Refer to
"Judgement of Line Pressure Test"
.
6.
SYMPTOM CHECK
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 7.
7.
CHECK TCM
1.
Check TCM input/output signal. Refer to
CVT-56, "TCM Input/Output Signal Reference Values"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-224, "Removal and Installation"
.
NG
>> Repair or replace damaged parts.
SAT494G
CVT-202
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November
2004 Murano
Cannot Be Changed to Second Position
ACS004MS
SYMPTOM:
Does not change to second position when selecting “S” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
CVT-62, "SELF-DIAGNOSTIC RESULT MODE"
Is any malfunction detected by self-diagnostic?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK SECOND POSITION SWITCH
Check second position switch circuit. Refer to
CVT-178, "SECOND POSITION SWITCH"
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
SYMPTOM CHECK
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 4.
4.
CHECK TCM
1.
Check TCM input/output signal. Refer to
CVT-56, "TCM Input/Output Signal Reference Values"
2.
If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-203
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
Cannot Be Changed to “L” Position
ACS004MT
SYMPTOM:
Does not change to “L” position when selecting “L” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
CVT-62, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-209, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
.
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
"Judgement of Line Pressure Test"
.
SCIA2001E
SAT638A
SAT494G
CVT-204
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November
2004 Murano
5.
SYMPTOM CHECK
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signal. Refer to
CVT-56, "TCM Input/Output Signal Reference Values"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-224, "Removal and Installation"
NG
>> Repair or replace damaged parts.
TROUBLE DIAGNOSIS FOR SYMPTOMS
CVT-205
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
Vehicle Does Not Decelerate by Engine Brake
ACS004ZA
SYMPTOM:
No engine brake is applied when the gear is shifted from the M2 to M1 or “S” to “L” position.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
CVT-62, "SELF-DIAGNOSTIC RESULT MODE"
.
Is any malfunction detected by self-diagnostic?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK CONTROL CABLE
Check control cable. Refer to
CVT-209, "Checking of CVT Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control cable. Refer to
.
3.
CHECK CVT FLUID LEVEL
Check CVT fluid level. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Refill CVT fluid.
4.
CHECK LINE PRESSURE
Check line pressure at idle. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> Check the malfunctioning item. Refer to
"Judgement of Line Pressure Test"
.
SCIA2001E
SAT638A
SAT494G
CVT-206
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November
2004 Murano
5.
CHECK MANUAL MODE SWITCH (WITH MANUAL MODE)
Check manual mode switch circuit. Refer to
CVT-132, "DTC P0826 MANUAL MODE SWITCH CIRCUIT"
.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace damaged parts.
6.
SYMPTOM CHECK
Check again. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 7.
7.
CHECK TCM
1.
Check TCM input/output signal. Refer to
CVT-56, "TCM Input/Output Signal Reference Values"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the transaxle assembly. Refer to
CVT-224, "Removal and Installation"
NG
>> Repair or replace damaged parts.
SHIFT CONTROL SYSTEM
CVT-207
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
SHIFT CONTROL SYSTEM
PFP:34901
Removal and Installation
ACS001ZN
COMPONENTS (WITH MANUAL MODE)
1.
Selector lever knob
2.
Knob cover
3.
A/T console finisher
4.
Control device assembly
5.
Lock pin
6.
Bracket
7.
Bracket
8.
Lock plate
9.
Control cable
10. Lock plate
SCIA5316E
CVT-208
SHIFT CONTROL SYSTEM
Revision: 2004 November
2004 Murano
COMPONENTS (WITHOUT MANUAL MODE)
1.
Selector lever knob
2.
Knob cover
3.
A/T console finisher
4.
Control device assembly
5.
Lock pin
6.
Bracket
7.
Bracket
8.
Lock plate
9.
Control cable
10. Lock plate
SCIA5317E
SHIFT CONTROL SYSTEM
CVT-209
D
E
F
G
H
I
J
K
L
M
A
B
CVT
Revision: 2004 November
2004 Murano
REMOVAL
1.
Remove knob cover below selector lever downward.
2.
Pull lock pin out of selector lever knob.
3.
Remove selector lever knob.
4.
Remove A/T console finisher.
●
IP-18, "Removal and Installation"
5.
Remove console box assembly.
●
IP-18, "Removal and Installation"
6.
Disconnect control cable of control device.
7.
Disconnect control device harness connector.
8.
Remove control device assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
After installation is completed, adjust and check CVT position.
Adjustment of CVT Position
ACS001ZO
1.
Place selector lever in “P” position.
2.
Loosen control cable nut and place manual lever in “P” position.
CAUTION:
Turn wheels more than 1/4 rotations and apply the park
lock.
3.
After pushing the control cable with the specified force toward
the rear, move your hands off the control cable.
4.
Connect control cable on manual lever.
CAUTION:
No application of a force to the manual lever.
5.
Tighten control cable nut.
Checking of CVT Position
ACS001ZP
1.
Place selector lever in “P” position, and turn ignition switch ON (engine stop).
2.
Make sure selector lever can be shifted to other than “P” posi-
tion when brake pedal is depressed. Also make sure selector
lever can be shifted from “P” position only when brake pedal is
depressed.
3.
Move the selector lever and check for excessive effort, sticking,
noise or rattle.
4.
Confirm the selector lever stops at each position with the feel of
engagement when it is moved through all the positions. Check
whether or not the actual position the selector lever is in
matches the position shown by the shift position indicator and
the transaxle body.
SCIA4377E
Specified force: 9.8 N (1.0 kg, 2.2 lb)
: 13 N·m (1.3 kg-m, 10 ft-lb)
SCIA2001E
SCIA4595E
CVT-210
SHIFT CONTROL SYSTEM
Revision: 2004 November
2004 Murano
5.
The method of operating the lever to individual positions cor-
rectly should be as shown in the figure.
6.
Confirm the back-up lamps illuminate only when lever is placed
in the “R” position. Confirm the back-up lamps do not illuminate
when selector lever is in the “P” or “N” position with the lever
pushed against the “R” position.
7.
Confirm the engine can only be started with the selector lever in
the “P” and “N” positions.
8.
Make sure transaxle is locked completely in “P” position.
9.
When selector lever is set to manual shift gate, make sure man-
ual mode is displayed on combination meter.
Shift selector lever to “+” and “-” sides, and make sure set shift position changes.
SCIA4299E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст