Nissan Murano Z50 (2004 year). Manual — part 194
POWER STEERING FLUID
PS-7
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
CAUTION:
Do not hold steering wheel in a located position for more than 10 seconds. (There is the possibility
that oil pump may be damaged.)
4.
Check generation of air bubbles and cloud in fluid.
5.
If air bubbles and the cloud don't fade, stop engine, hold air bleeding until air bubbles and the cloud fade.
Perform the 2nd and the 3rd procedures again.
6.
Stop engine, check fluid level.
PS-8
STEERING WHEEL
Revision: 2004 November
2004 Murano
STEERING WHEEL
PFP:48430
On-Vehicle Inspection and Service
AGS000CK
CHECKING CONDITION OF INSTALLATION
●
Check installation conditions of steering gear assembly, front suspension, axle and steering column.
●
Check if movement exists when steering wheel is moved up and down, to the left and right and to the axial
direction.
●
Check if the mounting bolts and nut for steering gear are loose
or not.
CHECKING STEERING WHEEL PLAY
1.
Set tires to the straight ahead, start engine, then turn steering wheel to the left and right lightly, and mea-
sure steering wheel movement on the outer circumference when steering wheel is turned up to the point
where tires start moving.
CHECKING NEUTRAL POSITION ON STEERING WHEEL
●
Check neutral position on steering wheel after confirming that front wheel alignment is correct. Refer to
FSU-5, "Wheel Alignment Inspection"
1.
Set vehicle to the straight direction, check if steering wheel is in the neutral position.
2.
If it is not in the neutral position, remove steering wheel and reinstall it correctly.
3.
If the neutral position cannot adjust in the two teeth of steering gear assembly, loosen tie-rod lock nuts of
steering outer sockets, then adjust tie-rods by the same amount in the opposite direction.
CHECKING STEERING WHEEL TURNING FORCE
1.
Park vehicle on a level and dry surface, set parking brake.
2.
Remove driver air bag module from steering wheel. Refer to
SRS-37, "DRIVER AIR BAG MODULE"
.
3.
Start engine at idle, make steering fluid reach to normal operat-
ing temperature [50 to 80
°
C (122 to 176
°
F)], then check steering
wheel turning torque with pre-load gauge (SST).
4.
If steering wheel turning force is out of specification, check relief hydraulic pressure of oil pump. Refer to
PS-28, "POWER STEERING OIL PUMP"
End play of the axial direction for steering wheel
: 0 mm (0 in)
Tightening torque
Bolt: 136 - 162 N·m (14 - 16 kg-m, 101 - 119 ft-lb)
Nut: 121.6 - 149.1 N·m (13 - 15, kg-m, 90 - 109 ft-lb)
SGIA0458E
Steering wheel play
: 0 - 35 mm (0 - 1.38 in)
Steering wheel turning force:
7.45 N·m (0.76 kg-m, 66 in-lb) or less
SGIA0459E
STEERING WHEEL
PS-9
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
CHECKING FRONT WHEEL TURNING ANGLE
●
Check front wheel turning angle after the toe-in inspection.
Place front wheels on turning radius gauges and rear wheels on
stands so that vehicle can be level. Check the maximum inner
and outer wheel turning angles for LH and RH road wheels.
●
Start engine and run at idle, turn steering wheel all the way right
and left, measure the turning angle.
●
Any turning angles are not adjustable. If any of steering angles are out of the specification, check if the fol-
lowing parts are worn or damaged.
–
Steering gear
–
Steering column
–
Front suspension components
If found that they are worn or damaged, replace them with new ones respectively.
Removal and Installation
AGS000CL
Refer to
FAA0016D
Tire Size
18 inch
Inner wheel (Angle: A)
Minimum
34
°
30
′
(34.5
°
)
Nominal
38
°
00
′
(38.0
°
)
Maximum
39
°
00
′
(39.0
°
)
Outer wheel (Angle: B)
Nominal
31
°
30
′
(31.5
°
)
SGIA0055E
PS-10
STEERING COLUMN
Revision: 2004 November
2004 Murano
STEERING COLUMN
PFP:48810
Removal and Installation
AGS000CM
CAUTION:
●
Care must be taken not to give axial impact to steering column assembly during removal and
installation.
●
Care must be taken not to move steering gear during removal of steering column assembly.
REMOVAL
1.
Set vehicle to the straight ahead-direction.
2.
Remove driver air bag module from steering wheel. Refer to
SRS-37, "DRIVER AIR BAG MODULE"
.
3.
Disconnect steering switch connector, remove steering wheel lock nut, then remove steering wheel. Refer
to
.
1.
Steering wheel lock nut
2.
Lid
3.
Steering wheel
4.
Combination switch and spiral cable 5.
Steering column assembly
6.
Hole cover seal
7.
Clamp
8.
Hole cover
9.
Lower joint
10. Tilt lever knob
SGIA0823E
STEERING COLUMN
PS-11
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
4.
Remove fixing screw of tilt lever knob, then remove tilt lever
knob from tilt lever.
5.
Remove instrument driver lower panel. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
6.
Remove steering column cover and ignition key finisher. Refer to
IP-10, "INSTRUMENT PANEL ASSEM-
.
7.
Remove NATS antenna amp. Refer to
BL-137, "How to Replace NATS Antenna Amp."
8.
Remove fixing screws of knee protector, then remove knee pro-
tector from vehicle.
9.
Remove combination switch and spiral cable from steering column assembly. Refer to
10. Disconnect harness connector from each switch on steering column shaft, then separate vehicle side har-
ness from it.
11. Remove lock nut and bolt, then separate lower joint from upper
joint.
12. Remove fixing nuts from steering member, remove steering col-
umn assembly from steering member.
13. Remove hole cover seal and clamp.
14. Remove mounting nuts, then remove hole cover from dash panel.
SGIA0469E
SGIA0470E
SGIA0471E
SGIA0473E
PS-12
STEERING COLUMN
Revision: 2004 November
2004 Murano
15. Raise vehicle, then remove mounting bolt (lower side) of lower
joint and remove lower joint from vehicle.
INSPECTION AFTER REMOVAL
●
Check if there is something wrong with jacket tube etc. And then if they are damaged, replace with new
one.
●
If vehicle is light shocked, check column length “L1” or “L2” as
shown in the figure. Then if it is out of the specified value,
replace with new one.
●
Check the turning torque of steering column with preload gauge (SST). If it is out of the specified value,
repair it or replace with new one.
INSTALLATION
●
Refer to
PS-10, "Removal and Installation"
for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
●
When installing steering column to steering member, install mounting nut from front side of vehicle.
INSPECTION AFTER INSTALLATION
●
After installing steering column to vehicle, check tilt device and
its operation range. Ranges of operation are shown in the figure.
●
Check if steering wheel operation can turn to the end of the left
and right smoothly.
SGIA0474E
Steering column length
L1: 182 mm (7.17 in)
L2: 242.6 mm (9.55 in)
SGIA0475E
Turning torque
: 0 - 0.2 N·m (0 - 0.02 kg-m, 0 - 2 in-lb)
SGIA0476E
STEERING COLUMN
PS-13
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
Disassembly and Assembly
AGS000CN
DISASSEMBLY
1.
Remove spring from steering column assembly and tilt lever.
2.
Remove fixing bolt of upper joint, then remove upper joint from
steering column assembly.
ASSEMBLY
●
Refer to
PS-13, "Disassembly and Assembly"
for tightening torque. Install in the reverse order of
removal.
1.
Steering column assembly
2.
Spring
3.
Tilt lever knob
4.
Upper joint
SGIA0824E
SGIA0479E
PS-14
POWER STEERING GEAR AND LINKAGE
Revision: 2004 November
2004 Murano
POWER STEERING GEAR AND LINKAGE
PFP:49001
Removal and Installation
AGS000CO
CAUTION:
Spiral cable may snap due to steering operation if steering column is separated from steering gear
assembly. Therefore fix steering wheel with a string to avoid turns.
REMOVAL
2WD
1.
Set wheels in the straight-ahead position.
2.
Remove lock nut and bolt, then separate lower joint from upper
joint.
3.
Remove tires from vehicle with power tool.
4.
Confirm slit of lower joint fits with the projection on rear cover
cap, furthermore marking position on steering gear assembly
nearly fits with the projection on rear cover cap.
5.
Remove cotter pin at steering knuckle, then loosen mounting nut.
1.
Steering gear assembly
2.
Cotter pin
3.
Rack mounting bracket
4.
Rack mounting insulator
5.
Sleeve
SGIA0486E
SGIA0471E
SGIA0487E
POWER STEERING GEAR AND LINKAGE
PS-15
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
6.
Use a ball joint remover (SST) to remove steering outer socket
from steering knuckle. Be careful not to damage ball joint boot.
CAUTION:
To prevent damage to threads and to prevent ball joint
remover (SST) from coming off, and temporarily tighten
mounting nut.
7.
Remove oil pipings (high pressure side and low pressure side)
from steering gear assembly, then drain fluid from pipings.
8.
Remove mounting bolt (lower side) of lower joint.
9.
Remove mounting bolts and nut of steering gear assembly, and
then remove steering gear assembly, rack mounting bracket,
rack mounting insulator and sleeve from vehicle.
SGIA0488E
SGIA0489E
SGIA0474E
SGIA0458E
PS-16
POWER STEERING GEAR AND LINKAGE
Revision: 2004 November
2004 Murano
AWD
1.
Set wheels in the straight-ahead position.
2.
Remove lock nut and bolt, then separate lower joint from upper
joint.
3.
Remove tires from vehicle with power tool.
4.
Remove undercover from vehicle with power tool.
5.
Confirm slit of lower joint fits with the projection on rear cover
cap, furthermore marking position on steering gear assembly
nearly fits with the projection on rear cover cap.
6.
Remove oil pipings (high pressure side and low pressure side)
from steering gear assembly, then drain fluid from pipings.
7.
Remove cotter pin at steering knuckle, then loosen mounting nut.
8.
Use a ball joint remover (SST) to remove steering outer socket
from steering knuckle. Be careful not to damage ball joint boot.
CAUTION:
To prevent damage to threads and to prevent ball joint
remover (SST) from coming off, and temporarily tighten
mounting nut.
SGIA0471E
SGIA0487E
SGIA0489E
SGIA0488E
POWER STEERING GEAR AND LINKAGE
PS-17
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
9.
Remove mounting bolt (lower side) of lower joint.
10. Remove front exhaust tube with power tool. Refer to
11. Remove rear propeller shaft. Refer to
12. Remove mounting nuts on lower position of stabilizer connecting rod with power tool.
13. Remove mounting bolts of stabilizer clamp and hang stabilizer on vehicle with power tool.
14. Remove steering hydraulic piping bracket from front suspension member. Refer to
15. Disconnect electrical rear engine mounting actuator harness connector. Refer to
.
16. Set jack under engine and front suspension member.
17. Remove mounting bolts of rear engine mounting insulator with power tool. Refer to
.
18. Loosen mounting nuts of front suspension member (front side).
19. Remove mounting bolts of member stay (body side) with power tool, then loosen mounting nuts of mem-
ber stay (front suspension member side).
20. Move jack down slowly (front suspension member side) to remove rear engine mounting insulator from
engine and front suspension member.
21. Remove mounting bolts and nut of steering gear assembly, and
then remove steering gear assembly, rack mounting bracket,
rack mounting insulator and sleeve from vehicle.
INSTALLATION
●
Refer to
PS-14, "Removal and Installation"
for tightening torque. Install in the reverse order of removal.
NOTE:
Refer to component parts location and do not reuse non-reusable parts.
●
When steering wheel is set in the straight ahead direction, con-
firm slit of lower joint fits with the projection on rear cover cap,
furthermore marking position on steering gear assembly nearly
fits with the projection on rear cover cap.
SGIA0474E
SGIA0458E
SGIA0487E
PS-18
POWER STEERING GEAR AND LINKAGE
Revision: 2004 November
2004 Murano
●
After installation, bleed air from piping. Refer to
PS-6, "Air Bleeding Hydraulic System"
INSPECTION AFTER INSTALLATION
●
Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.
POWER STEERING GEAR AND LINKAGE
PS-19
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
Disassembly and Assembly
AGS000EQ
SGIA0825E
PS-20
POWER STEERING GEAR AND LINKAGE
Revision: 2004 November
2004 Murano
CAUTION:
●
Secure steering gear assembly with a vise, using copper
plates or something similar to prevent it from being dam-
aged. Do not grip cylinder with a vise.
●
Before performing disassembly, clean steering gear assem-
bly with kerosene. Be careful not to bring any kerosene into
contact with the discharge and return port connectors.
DISASSEMBLY
1.
Remove cylinder tubes from gear housing assembly.
2.
Remove rear cover cap from gear housing assembly.
3.
Measure adjusting screw height from gear housing assembly,
then loosen adjusting screw.
CAUTION:
●
Do not turn adjusting screw more than twice.
●
Replace steering gear assembly when adjusting screw is
removed or more than twice.
4.
Use a rear cover wrench (SST) to remove rear cover from sub-
gear assembly.
5.
Remove O-ring with a flat-bladed screwdriver, and pull out rear
cover.
1.
Cotter pin
2.
Outer socket
3.
Boot clamp
4.
Boot
5.
Inner socket
6.
Boot clamp
7.
Gear housing assembly
8.
Cylinder tubes
9.
Rear cover cap
10. Rear cover
11.
O-ring
12. Sub-gear assembly
13. Rack oil seal
14. Rack assembly
15. Rack Teflon ring
16. O-ring
17. End cover assembly
SGIA0500E
SGIA0568E
SGIA0826E
SGIA0508E
POWER STEERING GEAR AND LINKAGE
PS-21
C
D
E
F
H
I
J
K
L
M
A
B
PS
Revision: 2004 November
2004 Murano
6.
Remove sub-gear assembly from gear housing assembly.
CAUTION:
In order to protect oil seal from any damage, pull sub-gear assembly out straightly.
7.
Loosen lock nut of outer socket, and remove outer socket.
8.
Remove boot clamps of the small diameter side and the large diameter side, then remove boot.
CAUTION:
When removing boots, be careful not to damage inner socket and gear housing assembly. If they
are is damaged, change them to avoid oil leaks.
9.
Drill out the punch caulking area on cylinder outer rim with a 3
mm (0.12 in) drill bit. [Drill approximately. 1.5 mm (0.059 in) in
depth.]
10. Remove end cover assembly with a 45 mm (1.77 in) open head (suitable tool).
CAUTION:
Be careful not to damage rack. If it is damaged, replace rack. Otherwise, oil leaks may result.
11. Pull rack assembly with rack oil seal out of gear housing assembly.
CAUTION:
Be careful not to damage cylinder. If it is damaged, replace gear housing assembly. Otherwise, oil
leaks may result.
12. Heat rack Teflon ring to approximately. 40
°
C (104
°
F) with a
dryer, then remove it and O-ring from rack.
CAUTION:
Be careful not to damage rack. If it is damaged, change to a
new one to avoid oil leaks.
13. Use a taped 29 mm (1.14 in) socket and an extension bar.
Remove rack oil seal from gear housing assembly.
CAUTION:
Be careful not to damage gear housing assembly and cylin-
der inner wall. If it is damaged, gear housing assembly
must be replaced. Otherwise, oil leaks will result.
INSPECTION AFTER DISASSEMBLY
Boot
Check boot for cracks and deformation. Replace it, if necessary.
Rack
Check rack for damage and wear. Replace it, if necessary.
STC0013D
SGIA0151E
SGIA0179E
PS-22
POWER STEERING GEAR AND LINKAGE
Revision: 2004 November
2004 Murano
Sub-Gear Assembly
●
Check pinion gear for damage and wear. Replace it, if necessary.
●
Check bearing while rotating it. Replace bearing if bearing ball race was dented, worn, or damaged.
Gear Housing Assembly
Check gear housing assembly for damage and scratches (inner wall). Replace it, if necessary.
Outer Socket and Inner Socket
Swing Torque
●
Hook a spring balance at the point shown in the figure. Confirm
if the reading is within the specification. When ball stud and
inner socket start moving the measured value must be within the
specification. If the reading is outside the specification, replace
socket.
Rotating Torque
●
Using a preload gauge (SST), check if reading is within the
range specified below. If the value is outside the standard,
replace outer sockets.
Axial End Play
●
Apply load of 490 N (50 kg, 110 lb) to ball stud axially. Use a dial
-gauge to measure the amount of the movement that the stud
makes. Check if the reading is within the specified below. If the
value is outside the standard, replace outer and inner sockets.
SGIA0547E
Item
Outer socket
Inner socket
Measuring point
Cotter pin hole of stud
Shown as L: 83.2 mm (3.276 in)
Swing torque
0.3 - 2.9 N·m (0.03 - 0.29 kg-m, 3 - 25 in-lb)
1.0 - 7.8 N·m (0.11 - 0.79 kg-m, 9 - 69 in-lb)
Measuring value
4.84 - 46.7 N (0.50 - 4.7 kg, 4 - 34 lb)
12.1 - 93.7 N (1.3 - 9.5, kg, 9 - 69 lb)
Rotating torque
0.3 - 2.9 N·m (0.03 - 0.29 kg-m, 3 - 25 in-lb)
SST882B
Outer socket
0.5 mm (0.02 in) or less
Inner socket
0.2 mm (0.008 in) or less
SGIA0057E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст