Nissan Murano Z50 (2004 year). Manual — part 16
AUDIO
AV-67
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
7.
Unlock FPC (Flexible Print Circuit) connector lock on A/C and
AV switch side.
8.
Pull off flexible printed circuit from connector.
CAUTION:
Make sure mating surface of FPC (Flexible Print Circuit) and
the direction of connector terminal.
9.
Remove screws (4) and clips (2). Then remove audio unit from
cluster lid C.
10. Remove audio unit screws (8), unified meter and A/C amp.
screws (2) and remove bracket.
CAUTION:
●
When carrying audio unit body, do not touch internal
mechanism access from cassette tape slot.
●
Be careful not to allow foreign material to enter from cas-
sette tape slot.
●
Use appropriate screws for each, as screws for audio unit
are different from that for unified meter and A/C amp.
INSTALLATION
Installation is the reverse order of removal.
PKIA2444E
PKIA2448E
PKIA2449E
AV-68
AUDIO
Revision: 2004 November
2004 Murano
Removal and Installation for A/C and AV Switch
AKS004NU
REMOVAL
1.
Remove audio unit from cluster lid C. Refer to
AV-66, "Removal and Installation of Audio Unit"
.
2.
Remove screws (8) and remove A/C and AV switch.
INSTALLATION
Installation is the reverse order of removal.
PKIA2452E
1.
Front finisher
2.
A/C and AV switch
3.
Screws
4.
Screws
5.
Cluster lid C
PKIA2451E
AUDIO
AV-69
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
Removal and Installation of Audio Steering Wheel Switch
AKS00AS9
REMOVAL
1.
Remove steering wheel. Refer to
PS-9, "Removal and Installation"
2.
Remove steering wheel cover.
3.
Remove screws (2) and remove audio steering wheel switch.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Front Door Speaker (Base system)
AKS004NV
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (4) and remove speaker.
3.
Remove screws (4) and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Front Door Speaker (BOSE system)
AKS004NW
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (3) and remove speaker.
3.
Remove screws (3) and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
SKIB0039E
PKIA2454E
PKIA2455E
AV-70
AUDIO
Revision: 2004 November
2004 Murano
Removal and Installation of Rear Door Speaker (Base system)
AKS004NX
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (3) and remove speaker.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Rear Door Speaker (BOSE system)
AKS004NY
REMOVAL
1.
Remove door finisher. Refer to
2.
Remove screws (3) and remove speaker.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Tweeter
AKS004NZ
REMOVAL
1.
Remove side ventilator assembly. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
2.
Remove instrument side finisher. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
3.
Remove screws (2) and remove tweeter.
INSTALLATION
Installation is the reverse order of removal.
PKIA2456E
PKIA2457E
PKIA2458E
AUDIO
AV-71
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
Removal and Installation of Woofer
AKS004O0
REMOVAL
1.
Open luggage floor finisher (center). Refer to
2.
Remove woofer clamp and remove connector.
3.
Remove woofer.
CAUTION:
●
Connectors must be placed in the left side, when installed.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of BOSE Speaker Amp.
AKS004R3
REMOVAL
1.
Remove luggage floor finisher (front). Refer to
.
2.
Remove screws (4) and connectors (2) and remove BOSE
speaker amp. from luggage floor.
3.
Remove screws (4) and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
PKIA2459E
PKIA2460E
PKIA2461E
AV-72
AUDIO ANTENNA
Revision: 2004 November
2004 Murano
AUDIO ANTENNA
PFP:28200
Location of Antenna
AKS004O1
Removal and Installation of Roof Antenna
AKS004O3
REMOVAL
1.
Remove head lining. Refer to
.
2.
Remove nut and antenna base.
3.
Remove instrument panel. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
4.
Remove antenna feeder (upper) and antenna feeder (lower).
5.
Remove clips (5), and separate antenna feeder (upper) from vehicle.
INSTALLATION
Installation is the reverse order of removal.
PKIA2462E
PKIA2463E
INTEGRATED DISPLAY SYSTEM
AV-73
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
INTEGRATED DISPLAY SYSTEM
PFP:28090
System Description
AKS004XS
A/C AND AV SWITCH SYSTEM
Refer to Owner
′
s Manual for A/C and AV switch operating instructions.
Using the A/C and AV switch at the center of the instrument panel, the controls of the following systems are
centralized:
●
Integrated display system (Drive computer, setting screen, clock, etc.)
●
Auto A/C system
●
Audio system
PRECAUTION OF LCD MONITOR
●
In order to use LED for backlight of a display, by in car temperature, brightness may change. In low tem-
perature, the refreshing rate of the picture also becomes low because of the low response of the LCD
monitor. When passenger room becomes warm, however, the LCD recovers the normal display.
●
Backlight sometimes flickers or darkens according to the total consumption hours and the number of times
switched ON and OFF. In this case, display unit should be replaced.(Exchange only of backlight is impos-
sible.)
POWER SUPPLY AND GROUND
Power Is Supplied At All Times
●
through 15A fuse [No. 38, located in fuse and fusible link block]
●
to audio unit terminal 6
●
to display unit terminal 1
●
to A/C and AV switch terminal 1.
When Ignition Switch Is In ACC or ON Position, Power Is Supplied
●
through 10A fuse [No. 6, located in fuse block (J/B)]
●
to unified meter and A/C amp. terminal 35
●
to display unit terminal 2
●
to audio unit terminal 10
●
to A/C and AV switch terminal 2
●
to BCM terminal 11.
When Ignition Switch Is In ON or START Position, Power Is Supplied
●
through 10A fuse [No. 12, located in fuse block (J/B)]
●
to unified meter and A/C amp. terminal 22
●
to display unit terminal 3.
Ground Is Supplied
●
to unified meter and A/C amp. terminals 29, 30
●
to display unit terminal 6
●
to A/C and AV switch terminal 5
●
to BCM terminals 49, 52
●
to low tire pressure warning control unit terminal 20
●
through body grounds M14 and M78.
AV-74
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November
2004 Murano
DRIVE COMPUTER
Refer to Owner
′
s Manual for drive computer operating instructions.
TRIP Switch
When “TRIP” switch is pushed, display TRIP screen. As TRIP infor-
mation, it indicates journey time (TIME), trip odometer (DIST), and
average vehicle speed (AVG).
Pushing “TRIP” switch once cycles display from TRIP 1
→
TRIP
2
→
Display OFF
→
TRIP 1.
“TIME”
●
Journey time indication is conducted by reset or battery connec-
tion.
●
When pushing “TRIP RESET” or “TRIP” switch more than
approximately 1.5 seconds, journey time will be reset.
●
If journey time is reset, journey distance and average speed will
be reset at the same time.
“DIST”
●
Trip odometer indication is conducted by vehicle speed signal.
●
When pushing “TRIP RESET” or “TRIP” switch more than approximately 1.5 seconds, driving distance will
be reset.
●
If trip odometer is reset, journey time average speed will be reset at the same time.
“AVG”
●
Average speed indication is conducted by running distance and running time.
●
Indication will be renewed every 30 seconds.
●
When pushing “TRIP RESET” or “TRIP” switch more than approximately 1.5 seconds, average speed will
be reset.
●
After reset operation, the displays shows “ ” for 30 seconds.
FUEL ECON Switch
When “FUEL ECON” switch is pushed, display FUEL ECON screen.
As FUEL ECON information, it indicates average fuel consumption
(AVG), and distance to empty (DTE).
Pushing “FUEL ECON” switch once cycles display from FUEL
ECON
→
Display OFF
→
FUEL ECON.
“AVG” (Average Fuel Consumption)
●
Average fuel consumption indication is conducted by ECM pulse
signal and vehicle speed signal after system is reset.
●
Indication will be renewed every 30 seconds.
●
When pushing “TRIP RESET” or “FUEL ECON” switch more
than approximately 1.5 seconds, average fuel economy will be
reset.
●
After reset operation, the display shows “ . ” until the vehicle is driven 1,600 ft. (500 m) or 30 seconds
has passed.
“DTE” (Distance to Empty)
●
Distance to empty receives via CAN communication and indicates values calculated by meter.
●
Display range is max 999 miles (max 999 km).
●
If low-fuel WARNING is received from combination meter via CAN communication, distance to empty indi-
cation will be “ ”.
●
Indication will be renewed every 30 seconds.
SKIA5916E
SKIA5917E
INTEGRATED DISPLAY SYSTEM
AV-75
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
MAINT Switch (Maintenance Switch)
●
When “MAINT” switch is pushed, display vehicle information screen. As vehicle information, it indicates
engine oil, tire rotation, and tire pressure.
●
Pushing “MAINT” switch once cycles display from engine oil
→
tire rotation
→
tire pressure
Note
→
engine oil.
NOTE:
There is not low tire pressure warning system becomes display OFF.
Engine Oil and Tire Rotation
●
Operating the joystick left/right, replace distance can be set.
●
When journey distance is the same as replace distance, alert is
displayed. (SERVICE ALERT setting is ON.)
●
Selected replace distance is 0 - 7,500 miles (0 - 12,000 km) in
increments of 500 mile (800 km).
●
Push and hold “TRIP RESET” or “MAINT” switch for 1.5 sec-
onds or longer, reset present journey distance.
●
During driving, cannot change settings.
Tire Pressure
●
Tire pressure signal is received from low tire pressure warning
control unit via CAN communication.
●
Tire pressure is displayed.
●
When FLAT TIRE signal is received from low tire pressure warn-
ing control unit, “FLAT TIRE” is displayed.
H,M Switch
●
When “H” or “M” switch is pushed and held for 1.5 seconds or more, mode is changed to clock mode.
●
Then “hour” and “minute” are flashed.
●
When “H” switch is pushed, “hour” is adjusted.
●
When “M” switch is pushed, “minute” is adjusted.
SKIA5918E
SKIA5919E
AV-76
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November
2004 Murano
SETTING SCREEN
When the “SETTING” button is pushed, the following menu will display on the screen.
DISPLAY ON/OFF
→
LANGUAGE
→
BEEP SET
→
SERVICE ALERT
→
PERSONALIZED SETTING MENU
→
OFF
Adjustable Vehicle Status
*: If equipped
Setting items
Operation
DISPLAY
●
To turn off the display, choose “OFF” on the screen using the joystick.
●
The confirmation will appear. Select “YES” to turn off, and “NO” to
cancel.
●
To turn on the display, push display screen control, air conditioner or
audio button.
LANGUAGE
To change the language, choose English or French using the joystick.
BEEP SET
To turn on/off the button beep sound, choose “ON” or “OFF” using the
joystick.
SERVICE ALERT
To display the maintenance information on the screen when it has
reached to the preset distance, choose “ON”.
PERSONALIZED
SETTING MENU
SLIDE BACK DR SEAT ON EXIT*
To set the driver's seat so that it automatically moves back and returns
to the original position for ease of entry and exit, choose “ON”.
REMOTE UNLOCK DOOR LOGIC*
To set the unlock doors of the 1st unlocking operation, choose the
desired function.
Only the driver side door
⇔
All the doors
HORN CHIRP WITH REMOTE*
To set the horn chirp mode that occurs when pushing the LOCK button
on the remote controller, choose the desired function.
LIGHTS FLASH WITH REMOTE*
To set the hazard indicator flash mode when the “LOCK” or “UNLOCK”
button on the remote controller is pushed, choose the desired function.
AUTO RE-LOCK TIME*
To set the auto door re-lock time, choose the desired time.
AUTO HEADLIGHTS SENSITIVITY*
To set the sensitivity level of the automatic headlights, choose the level.
AUTO HEADLIGHTS OFF DELAY*
To set the time for how long it takes the automatic turn off timer to extin-
guish the headlights in the AUTO position, select the “Automatic Head-
lights Off Delay” key, then move the joystick to the left or right to adjust
the timer.
SPEED SENSING WIPER INTERVAL*
To turn on the speed sensing wiper, choose “ON”.
CONFIRM RESET SETTINGS*
To reset all settings of the personalized settings to the initial conditions,
choose “YES”.
RESET ALL SETTINGS*
To reset all settings of the personalized settings to the initial conditions,
push “ENTER”.
INTEGRATED DISPLAY SYSTEM
AV-77
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
D/N Screen
●
When D/N switch is pushed, change screen of adjustment lumi-
nance.
●
If push D/N again when display adjustment luminance, change
DAY-NIGHT(NIGHT-DAY) mode (screen of adjustment lumi-
nance).
As follows:
●
Push “PREV” or not operate for 10sec. when displayed screen
of adjustment luminance, back to default screen (same mode).
●
Can adjust luminance by joystick (R/L) in adjustment screen.
●
Adjustment range is a 12 stage (MIN to MAX) and default set value is 10 (DAY) and 4 (NIGHT).
WARNING INDICATIONS
●
The door open warning will appear when the door is not securely closed while driving over 3 MPH (5 km/
h).
●
The door open warning will disappear when the vehicle speed slows down under 5 km/h (3 MPH) even if
the door is not securely closed yet.
AV COMMUNICATION LINE
Display unit is controlled by the following unit with AV communication line.
●
A/C and AV switch
CAN Communication System Description
AKS007PU
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicles are equipped with many electronic control units and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Unit
AKS007PV
Refer to
LAN-8, "CAN Communication Unit"
Component Parts and Harness Connector Location
AKS004XU
Now
Change display
DAY
DAY (adjustment)
→
NIGHT (adjustment)
→
DAY (adjustment)
→
·····
NIGHT
NIGHT (adjustment)
→
DAY (adjustment)
→
NIGHT (adjustment)
→
·····
SKIA4374E
SKIA9937E
AV-78
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November
2004 Murano
Schematic
AKS004YZ
TKWA1728E
INTEGRATED DISPLAY SYSTEM
AV-79
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
Wiring Diagram — INF/D —
AKS004Z0
TKWA0838E
AV-80
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November
2004 Murano
TKWA0839E
INTEGRATED DISPLAY SYSTEM
AV-81
C
D
E
F
G
H
I
J
L
M
A
B
AV
Revision: 2004 November
2004 Murano
TKWA1056E
AV-82
INTEGRATED DISPLAY SYSTEM
Revision: 2004 November
2004 Murano
TKWA1729E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст