Nissan Murano Z50 (2004 year). Manual — part 226
REAR WIPER AND WASHER SYSTEM
WW-53
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision: 2004 November
2004 Murano
INSTALLATION
Install in the reverse order of removal.
Washer Nozzle Adjustment
AKS00ANS
●
Adjust washer nozzle with suitable tool as shown in the figure.
Unit : mm (in)
Washer Tube Layout
AKS00ANT
Adjustable range
:
±
0.7
°
(vertical direction)
: +7
°
, -3
°
(horizontal direction)
PKIA8653E
h (height)
23.3 (0.91)
φ
(spray position range)
30 (1.18)
PKIA2565E
PKIA2566E
WW-54
REAR WIPER AND WASHER SYSTEM
Revision: 2004 November
2004 Murano
Removal and Installation of Rear Washer Nozzle
AKS00ANU
1.
Remove high-mounted stop lamp. Refer to
2.
Remove the rear washer nozzle mounting screw and remove it.
3.
Note the following, and install in the reverse order of removal.
●
Tighten rear washer nozzle mounting screw to specified
torque.
CAUTION:
●
After tightened rear washer nozzle mounting screw, make
sure that the rear washer nozzle does not come off when
it is pulled downward at 49N (5kg, 11lb) as shown in the
figure.
If the washer nozzle come off, replace it together with a
new high-mounted stop lamp assembly.
Check Valve Inspection
AKS00ANV
●
A check valve is provided in the washer fluid line. Be careful not
to connect check valve to washer tube in the wrong direction.
Removal and Installation of Rear Wiper and Washer Switch
AKS00ANW
Refer to
WW-35, "Removal and Installation of Front Wiper and Washer Switch"
.
Removal and Installation of Washer Tank
AKS00ANX
Refer to
WW-35, "Removal and Installation of Washer Tank"
.
Removal and Installation of Washer Pump
AKS00ANY
Refer to
WW-36, "Removal and Installation of Washer Pump"
Rear washer nozzle mounting screw
: 0.4 N·m (0.04 kg-m, 4 in-lb)
PKIA2548E
PKIA2955E
PKIA2546E
POWER SOCKET
WW-55
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision: 2004 November
2004 Murano
POWER SOCKET
PFP:253A2
Wiring Diagram — P/SCKT —
AKS004NM
TKWA0787E
WW-56
POWER SOCKET
Revision: 2004 November
2004 Murano
Removal and Installation of Instrument Power Socket
AKS004NN
REMOVAL
1.
Remove inner socket with power socket lid assembly from the
instrument panel, while pressing the pawls.
2.
Disconnect power socket connector.
3.
Remove inner socket from power socket lid assembly, while
pressing the hook out from square hole.
INSTALLATION
Instal in the reverse order of removal.
Removal and Installation of Luggage Room Power Socket
AKS005I6
REMOVAL
1.
Remove inner socket from the ring, while pressing the hook on
the ring out from square hole.
2.
Remove luggage side finisher lower (right). Refer to
in “EI” section.
3.
Turn holder nut counterclockwise and unlock it.
4.
Remove the ring from inner trim.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Console Power Socket
AKS005I5
1.
in “IP” section.
2.
Remove inner socket from the ring, while pressing the hook on
the ring out from square hole.
3.
Remove power socket finisher assembly mounting screws and
remove it.
4.
Remove the ring from power socket finisher while pressing
pawls.
PKIA2568E
PKIA2569E
PKIA2571E
HORN
WW-57
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision: 2004 November
2004 Murano
HORN
PFP:25610
Wiring Diagram — HORN —
AKS004NO
TKWA1720E
WW-58
HORN
Revision: 2004 November
2004 Murano
Removal and Installation
AKS004NP
REMOVAL
1.
Remove front bumper. Refer to
in
“EI” section.
2.
Disconnect horn connector.
3.
Remove horn bolt and remove horn from vehicle.
INSTALLATION
Tighten horn bolt to specified torque.
PKIA2570E
PKIA2559E
Horn mounting bolt
: 17.1 N·m (1.7 kg-m, 13 ft-lb)
CIGARETTE LIGHTER
WW-59
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision: 2004 November
2004 Murano
CIGARETTE LIGHTER
PFP:35330
Wiring Diagram — CIGAR —
AKS007O2
TKWA1057E
WW-60
CIGARETTE LIGHTER
Revision: 2004 November
2004 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст