Nissan PULSAR N13 Series / ASTRA LD Series. Manual — part 58
Body
233
Remove the lock assembly retaining bolts
and withdraw the lock assembly, insulator and link
from the tailgate.
Using a suitable screwdriver, remove the
lock cylinder retaining clip and withdraw the lock
cylinder from the vehicle.
Installation is a reversal of the removal procedure
with attention to the following points:
Ensure that the positioning of the lock is
correct in relation to the striker plate.
Ensure that the interior lamp switch wiring
connector is connected.
6. LUGGAGE COMPARTMENT LID
AND LOCK — SEDAN
LUGGAGE COMPARTMENT LID
To Remove
Raise the luggage compartment lid and place
protective covers over the surrounding paintwork.
Using a soft lead pencil, mark around the
luggage compartment lid hinges to aid assembly.
With the aid of an assistant supporting the
lid, remove the hinge retaining bolts and withdraw the
luggage compartment lid from the vehicle.
To Install and Adjust
With the aid of an assistant, install the
luggage compartment lid in position on the hinges
according to the marks made on removal. Install the
retaining bolts.
Close the lid and check the vertical and
lateral alignment of the l i d in relation to the body.
If adjustment is necessary, loosen the li d
hinge retaining bolts on one hinge at a time and adjust
the lid as required.
If vertical adjustment is required, loosen the
lid hinge retaining bolts and increase or decrease the
number of washers under the bolts.
If required, adjust the striker plate using the
procedure that follows.
STRIKER PLATE
To Remove, Install and Adjust
Fold back the trim material from inside the
luggage compartment.
Using a soft lead pencil, scribe a line around
the outside of each striker plate retaining bolt washer.
Remove the striker plate bolts and washers
and the screw retaining the remote release cable
bracket.
Installed view of the luggage compartment lid striker
with the trim material folded back.
(4) Slide the striker assembly towards the right
hand side of the vehicle and disconnect the remote
release cable. Withdraw the striker plate from the
vehicle.
Installation is a reversal of the removal procedure
with attention to the following points:
(1) Install the remote release cable to the striker
plate and install the striker plate retaining bolts and
washers to the lines made on dismantling.
Tighten the retaining bolts to just over finger
tight.
Close the lid ensuring that the striker has
actuated the locking mechanism.
Check the alignment of the luggage compart-
ment lid in its opening and adjust the locking action
by moving the striker plate. Tighten the retaining
bolts securely.
When the striker plate is adjusted correctly
pull the remote release cable towards the right hand
side of the vehicle until the cable end has 0.5-1.5 mm
clearance and tighten the retaining screws. Check the
operation of the remote release cable and readjust if
necessary.
Installed view of the luggage compartment lid hinge.
234
Body
LOCK ASSEMBLY
To Remove and Install
(1) Remove the retaining bolts and withdraw the
lock assembly from the luggage compartment lid.
Installation is a reversal of the removal procedure
ensuring that the actuating arm on the lock is under
the lock cylinder pivot.
LOCK CYLINDER
Installed view of the lock and lock cylinder.
LOCK CYLINDER
To Remove and Install
Remove the bolt retaining the lock cylinder
pivot to the luggage compartment lid inner panel.
Using a suitable screwdriver, remove the
lock cylinder retaining clip from under the lock.
Withdraw the lock cylinder and pivot from
the vehicle.
Installation is a reversal of the removal procedure.
(2) When the clips have been released, pull the
grille forward and remove it from the vehicle ensuring
that care is taken not to damage the grille.
Installation is a reversal of the removal procedure
with attention to the following points:
Remove the grille retaining clips from the
radiator support panel and install them to the
grille.
Renew any damaged clips.
Install the grille to the vehicle being careful to
align the grille clips before pushing the grille inwards.
Post July 1989 Pulsar Models
Fabricate a tool to engage the radiator grille
clips from the inside; an old spanner of suitable
dimensions can be ground down if necessary.
Using the above tool, turn the lower radiator
clips slightly to allow removal of the grille.
7. RADIATOR GRILLE
TO REMOVE AND INSTAL
Astra Models and Pre July 1989 Pulsar Models
(1) Using a flat bladed screwdriver, turn the
grille clips slightly to allow removal of the grille.
Installed view of the radiator grille on pre July 1989
models showing the retaining clip locations.
Installed view of the radiator grille on post July 1989
models showing the retaining clip locations and the
special tool required to release the lower clips.
Using a flat bladed screwdriver, turn the
upper grille clips slightly to allow removal of the grille.
When all the clips have been released, pull
the grille forward and remove it from the vehicle
ensuring that care is taken not to damage the grille.
Installation is a reversal of the removal procedure
with attention to the following points:
Remove the grille clips from the radiator
support panel and install them to the grille. Renew any
damaged clips.
Install the grille to the vehicle being careful to
align the grille clips before pushing the grille inwards.
8. CENTRE CONSOLE
TO REMOVE AND INSTAL
Remove the carpet square from the rear part
of the console and remove the screws underneath.
Prise out the trim piece below the handbrake
Body
235
lever and remove the screws underneath. Withdraw
the rear console.
On manual transaxle models, unscrew the
gear lever knob and prise out the gear lever rubber
boot.
On automatic transaxle models, prise out the
panel around the selector lever and maneuver the
panel over the lever.
Remove the screws retaining the front of the
console to the floor panel and withdraw the console
from the vehicle.
Installation is a reversal of the removal procedure.
9, DASHBOARD
TO REMOVE AND INSTAL
Disconnect the negative battery terminal.
Remove the centre console as previously
described in this section.
Remove the steering wheel as described in
the Steering section.
Remove the upper and lower steering col-
umn shrouds and remove the combination switch.
Refer to the Electrical System section if necessary.
Remove the retaining screws and withdraw
the lower trim panel from underneath the steering
column.
Remove the screws from underneath the
bonnet lock handle and slide the bonnet lock handle
downwards out of the dashboard.
Remove the screws retaining the centre fas-
cia panel, two upper and two lower, withdraw the
fascia panel slightly and disconnect the wiring to the
cigarette lighter.
Dismantled view of the centre console assembly. Au-
tomatic transaxle model.
Remove the radio/cassette bracket retaining
screws. Disconnect the aerial and the wiring and
withdraw the radio/cassette from the centre bracket.
Remove the heater control knobs and re-
move the heater fascia panel screws. Carefully remove
the heater fascia panel leaving the heater controls in
place.
Loosen the bolt retaining the large wiring
connector at the lower right hand side of the dash-
board. As the bolt is loosened it will force the
connector apart.
Using a screwdriver, carefully prise out the
demister ducts from the top of the dashboard.
Using a suitable socket, remove the bolts
from underneath the demister ducts.
Remove the bolts from the outer lower edges
and the lower part of the centre bracket assembly.
NOTE: Refer to the illustration for the
location of the dashboard retaining bolts.
(14) With the aid of an assistant lift the dash-
board straight up at the door pillar brackets. Tilt the
View of the dashboard removed from the vehicle. The arrows indicate the location of the retaining bolts.
236
Body
top of the dashboard rearwards and maneuver the
dashboard through the front door opening.
Installation is a reversal of the removal procedure
with attention to the following points:
With the aid of an assistant, ensure that the
outer edges of the dashboard engage properly with the
door pillar brackets.
Hold the dashboard in position and loosely
install all retaining bolts. Align the dashboard
and
tighten all screws and bolts securely.
10. SEAT BELTS
The front and outer rear seats are equipped with
lap/sash inertia reel seat belts, which are designed to
lock with any sudden change in vehicle motion.
The centre rear seat is equipped with a manually
adjustable lap seat belt.
Child restraint anchorages are located on the
parcel shelf behind the rear seat on Sedan models and
at the rear of the luggage compartment floor on
Hatchback models. These anchorages must be used if
a child's seat or capsule is installed to the vehicle. The
anchorages should not be used for adult scat bells or
harnesses.
The seat belts should be periodically inspected as
described below. Any seat belt assembly that is worn
or damaged, or has been subjected to abnormal
loadings in a collision, should be renewed as a
complete assembly.
Only mild soap and water should be used to clean
the webbing. Contamination with polish, oil, bleaches
and other chemicals should be avoided.
TO INSPECT
( 1 ) Check the seat belt webbing for fraying, cuts,
burns or other damage. On inertia reel belts, slowly
pull the belt from the reel to allow the entire length to
be examined. If the webbing is damaged or worn,
renew the seat belt assembly.
Check the seat belt webbing for fraying, cuts, burns or
other damage.
Ensure that the belts are not twisted.
Check all retaining nuts and bolts for secu-
rity.
Inspect the belt buckles for correct and
secure engagement. If the buckles are damaged or do
not function correctly, renew the seat belt assembly.
On inertia reel seat belts, check the retractor
mechanism as follows:
Pull the belt slowly from the reel and check
for smooth operation. Release the belt and ensure that
it retracts fully.
Pull the belt rapidly from the reel. The reel
should lock.
Drive the vehicle at walking pace and at-
tempt to withdraw the belt slowly while braking
sharply. The reel should lock.
If the retractor mechanism does not function
correctly, renew the seat belt assembly.
11. SEATS
FRONT SEAT
To Remove and Install
Adjust the seat to the most forward position.
Remove the mounting bolts from the rear of
the seat.
Adjust the seat to allow access to the mount-
ing bolts at the front of the seat.
Remove the mounting bolts and withdraw
the seat from the vehicle.
Installed view of the front seat belt with the door pillar
trim removed showing the mounting points.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст