Nissan Silvia. Manual — part 165
Wiring Diagram
NMEC0753
TEC814
GI
MA
EM
LC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Wiring Diagram
EC-175
Diagnostic Procedure
NMEC0754
1
INSPECTION START
Do you have CONSULT-II?
Yes or No
Yes
©
GO TO 2.
No
©
GO TO 3.
2
CHECK OVERALL FUNCTION
With CONSULT-II
1. Turn ignition switch “ON”.
2. Select “VALVE TIMING SOL” in “ACTIVE TEST” mode with CONSULT-II.
3. Touch “ON” CONSULT-II screen.
SEC437C
4. Check for operating sound of the intake valve timing control solenoid valve.
Clicking noise should be heard.
OK or NG
OK
©
INSPECTION END
NG
©
GO TO 4.
3
CHECK OVERALL FUNCTION
Without CONSULT-II
1. Lift up vehicle, start engine and warm it up to normal operation temperature.
2. Shift to a suitable gear position other than “P” or “N” position.
3. Check voltage between ECM terminal 105 (Intake valve timing control solenoid valve signal) and ground under the fol-
lowing conditions.
SEC438C
OK or NG
OK
©
INSPECTION END
NG
©
GO TO 4.
INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Diagnostic Procedure
EC-176
4
CHECK POWER SUPPLY
1. Turn ignition switch “OFF”.
2. Disconnect intake valve timing control solenoid valve harness connector.
SEC385C
3. Turn ignition switch “ON”.
4. Check voltage between terminal 2 and ground with CONSULT-II or tester.
SEC439C
OK or NG
OK
©
GO TO 6.
NG
©
GO TO 5.
5
DETECT MALFUNCTIONING PART
Check the following.
I
Harness connector F4, M60
I
10A fuse
I
Harness for open or short between valve timing control solenoid valve and fuse
©
Repair harness or connectors.
6
CHECK OUTPUT SIGNAL CIRCUIT
1. Turn ignition switch “OFF”.
2. Disconnect ECM harness connector.
3. Check harness continuity between ECM terminal 105 and intake valve timing control solenoid valve harness connector
terminal 1. Refer to wiring diagram.
Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 7.
NG
©
Repair open circuit or short to ground to short to power or connectors.
GI
MA
EM
LC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Diagnostic Procedure (Cont’d)
EC-177
7
CHECK VALVE TIMING CONTROL SOLENOID VALVE
Refer to “Component Inspection”, EC-178.
OK or NG
OK
©
GO TO 8.
NG
©
Replace valve timing control solenoid valve.
8
CHECK INTERMITTENT INCIDENT
Perform “TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT”, EC-82.
©
INSPECTION END
SEC440C
Component Inspection
NMEC0755
INTAKE VALVE TIMING CONTROL SOLENOID VALVE
NMEC0755S01
1.
Check oil passage visually for any metal debris.
2.
Supply intake valve timing control solenoid valve terminals with
battery voltage.
3.
Make sure that inside plunger protrudes.
If NG, replace intake valve timing control solenoid valve.
INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Diagnostic Procedure (Cont’d)
EC-178
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст