Nissan Silvia. Manual — part 298
Commercial Service Tools
NMMT0002
Tool name
Description
Slide hammer puller
SMT054E
Removing 6th coupling sleeve & synchronizer hub
assembly
(Use with quick steering puller)
Quick steering puller
SMT055E
Use with slide hammer puller
GI
MA
EM
LC
EC
FE
CL
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
PREPARATION
Commercial Service Tools
MT-5
NMMT0023
NVH Troubleshooting Chart
NMMT0023S01
Use the chart below to help you find the cause of the problem. The numbers indicate the order of the inspec-
tion. If necessary, repair or replace these parts.
MANUAL TRANSMISSION
NMMT0023S0101
Reference page
Refer
to
MT
-7,
“Checking
M/T
Oil”.
MT
-15
MT
-31
SUSPECTED PARTS
(Possible cause)
OIL
(Level
low)
OIL
(W
rong)
OIL
(Level
too
high)
GASKET
(Damaged)
OIL
SEAL
(W
orn
or
damaged)
CHECK
PLUG
RETURN
SPRING
AND
CHECK
BALL
(W
orn
or
damaged)
SHIFT
FORK
(W
orn)
GEAR
(W
orn
or
damaged)
BEARING
(W
orn
or
damaged)
BAULK
RING
(W
orn
or
damaged)
INSER
T
SPRING
(Damaged)
Symptom
Noise
1
2
3
3
Oil leakage
3
1
2
2
Hard to shift or will not shift
1
1
2
2
Jumps out of gear
1
2
2
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
MT-6
SMA103
Checking M/T Oil
NMMT0061
Never start engine while checking oil level.
1.
Check manual transmission for leakage.
2.
Check oil level.
Filler plug:
: 27 - 48 N·m (2.7 - 4.9 kg-m, 20 - 35 ft-lb)
SMA255A
Changing M/T Oil
NMMT0062
Oil grade and viscosity:
Refer
to
“RECOMMENDED
FLUIDS
AND
LUBRICANTS”, MA-8.
Oil capacity:
FS6R92A
1.8 liters (3-7/8 US pt, 3-1/8 Imp pt)
Drain plug:
: 27 - 48 N·m (2.7 - 4.9 kg-m, 20 - 35 ft-lb)
GI
MA
EM
LC
EC
FE
CL
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
M/T OIL
Checking M/T Oil
MT-7
FMT001
Replacing Rear Oil Seal
NMMT0003
REMOVAL
NMMT0003S01
1.
Remove the propeller shaft.
2.
Using a oil seal puller (SST), remove the oil seal.
FMT002
INSTALLATION
NMMT0003S02
1.
Apply multi-purpose grease to the oil seal lips. Then, drive the
oil seal with a drift (SST) until the oil seal is flush with the end
surface of the case.
CAUTION:
I
Do not reuse the removed oil seal. Always use a new oil
seal.
I
Install the oil seal so that it is fit level without inclination.
2.
Install the propeller shaft.
CAUTION:
If oil has leaked during this operation, check the oil level after
completing the operation.
SMT056E
Position Switch Check
NMMT0004
Switch
Gear position
Continuity
Back-up lamp switch
Reverse
Yes
Except reverse
No
PNP switch
Neutral
Yes
Except neutral
No
ON-VEHICLE SERVICE
Replacing Rear Oil Seal
MT-8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст