Nissan Silvia. Manual — part 247
SFE562A
b.
Hold the sides of the connector, push in tabs, and pull out the
tube inserted in the retainer.
CAUTION:
I
The tube can be removed when the push in tabs are com-
pletely depressed. Do not twist it more than necessary.
I
Do not use any tools to remove the quick connector.
SFE367A
8.
Remove exhaust center tube, propeller shaft, differential
carrier, rear suspension member and drive shafts (Refer to RA
section).
9.
Disconnect filler hose at fuel tank side and vent hose at filler
tube side.
JFE687A
10. Disconnect EVAP hose at the lower right-hand side of fuel
tank.
JFE688A
11. Set a suitable transmission jack under fuel tank.
JFE689A
12. Remove fuel tank band mounting bolts while supporting fuel
tank.
13. Remove fuel tank.
GI
MA
EM
LC
EC
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FUEL SYSTEM
Fuel Tank (Cont’d)
FE-7
SFE368A
INSTALLATION
NMFE0010S02
Installation procedure is the reverse order of removal.
I
When installing filler collar, place the protrusion of the collar
flange upward.
SFE369A
I
When installing the grommet of the filler tube, align the protru-
sion on the grommet with the notch on the filler tube.
SFE370A
I
When installing the inspection hole, put the arrow mark for-
ward.
Fuel Pump and Fuel Level Sensor Unit
NMFE0011
JFE691A
1.
Lock ring
2.
Upper plate
3.
Jet pump
FUEL SYSTEM
Fuel Tank (Cont’d)
FE-8
4.
Seal packing
5.
Fuel tube
6.
Relief valve
7.
Fuel tube
8.
Fuel pump
9.
Fuel tube
10. Fuel pump bracket
11. Fuel level sensor unit
12
Fuel tank
SFE376A
REMOVAL
NMFE0011S01
1.
Release fuel pressure.
Refer to FE-4, “Changing Fuel Filter”.
2.
Remove inspection hole cover located behind the rear seat.
3.
Disconnect harness connectors and fuel tubes on upper plate.
I
Put mating marks on tubes for correct installation.
4.
Remove lock ring (Use SST).
SFE371A
5.
While lifting upper plate, disconnect fuel tube and harness
connectors.
6.
Remove fuel pump pulling the top end of the fuel pump bracket
upward.
7.
Remove fuel level sensor unit.
a.
Pull fuel level sensor unit horizontally to the left.
SFE373AA
b.
Remove harness connector.
I
Carefully place the removed connector in the fuel tank so that
it can be pulled out for the installation.
GI
MA
EM
LC
EC
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FUEL SYSTEM
Fuel Pump and Fuel Level Sensor Unit (Cont’d)
FE-9
INSTALLATION
NMFE0011S02
To install, reverse the removal procedure.
CAUTION:
I
Always replace O-ring with a new one.
I
After installation, run engine and check for leaks at con-
nections.
I
Take extreme care for the fuel pump and fuel level sensor unit
not to drop or give similar impact.
I
Check for no foreign objects on the fuel pump filter.
I
Fuel hose and connector should be connected securely.
JFE692A
I
Install upper plate by aligning mating marks.
I
Using lock ring socket (SST), tighten the lock ring.
SFE562A
I
Connect quick connector by the following procedures.
a)
Check for no foreign objects, damage to the connection part.
b)
Align connector and axial center and insert the tube until “click”
sound is heard.
c)
After connection, visually check the secure connection by the
following procedures.
I
Visually check that two retainer’s pawls are connected to the
connectors.
I
By pulling tube and connector, check for secure connection.
SFE370A
I
Install inspection hole cover by facing the arrow mark to the
front of the vehicle.
FUEL SYSTEM
Fuel Pump and Fuel Level Sensor Unit (Cont’d)
FE-10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст