Nissan Silvia. Manual — part 76
SFA325B
4.
Check wheel bearing axial end play.
Axial end play: 0.05 mm (0.0020 in) or less
SFA595B
ABS Sensor Rotor
REMOVAL
NMAX0034
Remove ABS sensor rotor (models equipped with ABS) or labyrinth
plate (models without ABS) with suitable tool.
SFA596B
INSTALLATION
NMAX0035
Press-fit ABS sensor rotor or labyrinth plate.
SFA548A
Baffle Plate
REMOVAL
NMAX0036
I
Mark matchmarks on baffle plate before removing.
I
If baffle plate replacement requires removal of knuckle spindle,
separate it equally using a screwdriver.
Be careful not to scratch knuckle spindle.
SFA549A
INSTALLATION
NMAX0037
With matchmarks aligned, install baffle plate by tapping it with a
copper hammer and a suitable tool.
GI
MA
EM
LC
EC
FE
CL
MT
AT
PD
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Wheel Hub and Knuckle (Cont’d)
AX-7
Service Data and Specifications (SDS)
WHEEL BEARING (FRONT)
NMAX0021
Wheel bearing axial end play limit
mm (in)
0.05 (0.0020)
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
206 - 284 (21 - 29, 152 - 210)
FRONT AXLE
Service Data and Specifications (SDS)
AX-8
SBR820B
Precautions
PRECAUTIONS
NMAX0022
I
When installing each rubber part, final tightening must be
carried out under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
Use flare nut wrench when removing or installing brake
tubes.
I
After installing removed suspension parts, check wheel
alignment.
I
Do not jack up at the trailing arm and lateral link.
I
Always torque brake lines when installing.
Preparation
SPECIAL SERVICE TOOLS
NMAX0032
Tool number
Tool name
Description
ST30031000
Bearing puller
NT412
Removing inner race of wheel bearing
a: 50 mm (1.97 in) dia.
GG94310000
Flare nut torque wrench
NT406
Removing and installing brake piping
a: 10 mm (0.39 in) dia.
COMMERCIAL SERVICE TOOLS
NMAX0024
Tool name
Description
GG94310000
1 Flare nut crowfoot
2 Torque wrench
NT360
Removing and installing brake piping
a: 10 mm (0.39 in)
GI
MA
EM
LC
EC
FE
CL
MT
AT
PD
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REAR AXLE
Precautions
AX-9
Tool name
Description
Rear wheel hub drift
NT073
Installing wheel bearing
a: 49 mm (1.93 in) dia.
b: 41 mm (1.61 in) dia.
Wheel bearing drift
NT073
Removing rear wheel hub
a: 40 mm (1.57 in) dia.
b: 26 mm (1.02 in) dia.
Rear drive shaft plug
seal drift
NT065
Installing rear drive shaft plug seal
a: 85 mm (3.35 in) dia.
b: 67 mm (2.64 in) dia.
Noise, Vibration and Harshness (NVH)
Troubleshooting
NMAX0025
Refer to “Noise, Vibration and Harshness (NVH) Troubleshooting”,
“FRONT AXLE”, AX-3.
SMA525A
On-vehicle Service
REAR AXLE PARTS
NMAX0026
Check axle and suspension parts for looseness, wear or damage.
I
Shake each rear wheel.
I
Retighten all axle and suspension nuts and bolts to the speci-
fied torque.
Tightening torque:
Refer to REAR SUSPENSION (SU-18).
I
Make sure that cotter pins are inserted.
SRA227A
REAR WHEEL BEARING
NMAX0027
I
Check wheel bearings smooth operation.
I
Check axial end play.
Axial end play:
0.05 mm (0.0020 in) or less
I
If out of specification or wheel bearing does not turn smoothly,
replace wheel bearing assembly.
Refer to REAR AXLE — Wheel Hub and Axle Housing (AX-11).
REAR AXLE
Preparation (Cont’d)
AX-10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст