Nissan Silvia. Manual — part 107
Door Limit Switch Reset (Driver side only)
=NMBT0008
RESET CONDITIONS
NMBT0008S01
After each of the following operations are performed, reset the limit
switch (with built-in motor).
I
Regulator removal and installation
I
Removal of motor from regulator
I
Operation of regulator as a single unit
I
Door glass removal and installation
I
Glass run removal and installation
I
Fitting adjustment
JBT127A
RESET PROCEDURES
NMBT0008S02
After installing parts, proceed as follows:
1.
Close the door window completely.
2.
Press the reset switch and open the door window completely.
3.
Release the reset switch. After making sure the reset switch
has returned to the original position, close the door window
completely.
4.
The limit switch is now reset.
CAUTION:
Be sure to manually open or close the door window. (Do not
use the automatic open-close procedures.)
GI
MA
EM
LC
EC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
DOOR
Door Limit Switch Reset (Driver side only)
BT-19
Door Lock
=NMBT0010
JBT128A
I
For removal of door finisher, refer to “DOOR TRIM”, BT-29.
I
Remove sealing screen.
JBT129A
BELL CRANK ADJUSTMENT
NMBT0010S01
CAUTION:
Before adjusting bell crank, make sure that rod is installed to
inside handle.
After installing door lock and inside handle, set them in the lock
position. Expand rod holder. Remove rod free play at joining area
and set rod in position.
After adjusting bell crank adjustments have been made, operate
door lock knob, door lock switch and door key to make sure that
they lock and unlock properly.
SBT978
OUTSIDE HANDLE ROD ADJUSTMENT
NMBT0010S02
Rotate rod holder so that rod-to-holder clearance is adjusted as
shown in the figure at left.
CAUTION:
Make sure that rod-to-holder clearance is not “0” mm (0 in),
and that rod is not held pressed.
DOOR
Door Lock
BT-20
REMOVAL
=NMBT0010S03
I
For removal of front door finisher, refer to “DOOR TRIM”,
BT-29.
I
Remove sealing screen.
I
For removal of front door glass and guide rail, refer to “Door
Glass”, BT-14.
SBT980
1.
Remove inside handle escutcheon A.
2.
Remove screw securing inside handle.
3.
Detach bell crank at lock knob joining area.
4.
Detach inside handle rod on the door lock assembly side.
5.
Slide inside handle backward and remove inside handle.
6.
Remove rod from inside handle.
7.
Detach key lock rod and outside handle rod at joining area (on
the outside handle side).
8.
Disconnect door lock actuator connector.
9.
Remove screws securing door lock assembly, then remove
door lock assembly.
JBT130A
10. Remove nuts securing outside handle, then remove outside
handle assembly.
11. Remove nuts securing key cylinder, then remove key cylinder.
GI
MA
EM
LC
EC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
DOOR
Door Lock (Cont’d)
BT-21
Removal and Installation
NMBT0012
CAUTION:
I
Disconnect ground terminal from battery in advance.
I
Disconnect air bag system line in advance.
I
Never tamper with or force air bag lid open, as this may
adversely affect air bag performance.
I
Be careful not to scratch pad and other parts.
SBT101A
*1
*2
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
BT-22
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст