Nissan Silvia. Manual — part 227
SEM365EA
4.
Remove steel oil pan.
a.
Insert Tool between aluminum oil pan and steel oil pan.
I
Be careful not to damage aluminum mating surface.
I
Do not insert screwdriver, or oil pan flange will be dam-
aged.
b.
Slide Tool by tapping on the side of the Tool with a hammer.
c.
Remove steel oil pan.
SEM976E
d.
Remove baffle plate.
SEM977E
5.
Install engine slingers to cylinder head. Refer to “ENGINE
ASSEMBLY” (EM-65).
6.
Set a suitable hoist on engine slinger and hold the engine.
7.
Remove the following parts.
I
Tension rod bolts at transverse links
I
Front stabilizer bar securing bolts and nuts from side member.
I
Both left and right side engine mounting bolts. Refer to
“ENGINE ASSEMBLY” (EM-65) and “Front Suspension”
(SU-9.
8.
Disconnect steering shaft lower joint.
SEM790E
9.
Remove power steering tube bracket securing bolts at left ten-
sion rod bracket.
10. Remove front suspension member securing bolts while sup-
porting with a jack.
11. Lower front suspension member by around 60 mm (2.36 in).
SEM978E
12. Remove alternator support.
GI
MA
LC
EC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
OIL PAN
Removal (Cont’d)
EM-21
SEM043D
13. Remove rear cover plate.
SEM979E
14. Remove aluminum oil pan bolts in numerical order.
SEM980E
15. Remove four oil pan-to-transmission bolts.
16. Remove two engine-to-transmission bolts and install them into
open bolt holes shown. Tighten the two bolts to release alumi-
num oil pan from cylinder block.
SEM365EA
17. Remove aluminum oil pan.
a.
Insert Tool between cylinder block and aluminum oil pan.
I
Be careful not to damage aluminum mating surface.
I
Do not insert screwdriver, or oil pan flange will be
deformed.
b.
Slide Tool by tapping on the side of the Tool with a hammer.
c.
Remove aluminum oil pan.
SEM223D
18. Remove two oil pan-to-transmission bolts previously installed
in aluminum oil pan.
OIL PAN
Removal (Cont’d)
EM-22
SEM050D
Installation
NMEM0010
1.
Install aluminum oil pan.
a.
Use a scraper to remove old liquid gasket from mating sur-
faces.
I
Also remove old liquid gasket from mating surfaces of
cylinder block and front cover.
SEM357E
b.
Apply a continuous bead of liquid gasket to mating surface of
aluminum oil pan.
I
Use Genuine Liquid Gasket or equivalent.
I
Apply to groove on mating surface.
I
Allow 7 mm (0.28 in) clearance around bolt holes.
SEM981E
I
For areas marked with “
★
”, apply liquid gasket around the
outer side of the bolt hole as shown.
I
Be sure liquid gasket diameter is 4.0 to 5.0 mm (0.157 to
0.197 in).
I
Attaching should be done within 5 minutes after coating.
SEM982E
c.
Tighten nuts and bolts in numerical order.
Bolts 1 - 16:
: 16 - 19 N·m (1.6 - 1.9 kg-m, 12 - 14 ft-lb)
Bolts 17, 18:
: 6.4 - 7.5 N·m (0.65 - 0.76 kg-m, 56.4 - 66.0 in-lb)
2.
Install the four oil pan-to-transmission bolts.
3.
Install rear cover plate.
4.
Install alternator support.
5.
Tighten front suspension member securing bolts.
6.
Install all removed parts after removing steel oil pan.
GI
MA
LC
EC
FE
CL
MT
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
OIL PAN
Installation
EM-23
SEM051D
7.
Install steel oil pan.
a.
Use a scraper to remove old liquid gasket from mating surface
of steel oil pan.
I
Also remove old liquid gasket from mating surface of alu-
minum oil pan.
SEM015E
b.
Apply a continuous bead of liquid gasket to mating surface of
steel oil pan.
I
Use Genuine Liquid Gasket or equivalent.
I
Apply to groove on mating surface.
I
Allow 7 mm (0.28 in) clearance around bolt hole.
SEM983E
I
Be sure liquid gasket diameter is 4.0 to 5.0 mm (0.157 to
0.197 in).
I
Attaching should be done within 5 minutes after coating.
SEM984E
c.
Tighten bolts in numerical order as shown.
I
Wait at least 30 minutes before refilling engine oil.
OIL PAN
Installation (Cont’d)
EM-24
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст